Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C137BA2  Brake System Control Module "A" System Voltage System Voltage Low  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the No. 2 skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits operation of ABS, brake assist, regenerative brake cooperative control, etc.

This DTC is stored when the +BS, IG1 or IG2 terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the auxiliary battery or DC/DC converter circuit, etc.

This DTC is cleared when the voltage at terminal +BS, IG1 and IG2 returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C137BA2 Brake System Control Module "A" System Voltage System Voltage Low Any of the following is detected:
·

When the +BS terminal voltage is below 9.5 V, the power source voltage for all speed sensors is continuously low for 60 seconds or more.

·

When the voltage at terminal +BS is less than 8.5 V, the master cylinder pressure sensor is invalid for 10 seconds or more.

·

When the voltage at terminal +BS is less than 8.5 V, the brake pedal stroke sensor assembly is invalid for 10 seconds or more.

·

When the vehicle speed is 3 km/h (2 mph) or more, the voltage at terminal IG1 or terminal IG2 is excessively low for 10 seconds or more.

·

When the +BS terminal voltage is below 9.5 V and the solenoid relay is ON, the relay contact is OFF continuously for 1.22 seconds or more.

·

When the +BS terminal voltage is below 9.5 V, motor fail-safe relay overcurrent continues for 1.05 seconds or more.


·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

C137BA2 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7
Diagnosis Condition When the voltage at terminal +BS is less than 8.5 V ○ ○ - - - - -
When the +BS terminal voltage is below 9.5 V - - ○ - - - ○
When the vehicle speed is 3 km/h (2 mph) or more - - - ○ ○ - -
When the +BS terminal voltage is below 9.5 V and the solenoid relay is ON - - - - - ○ -
Malfunction Status The master cylinder pressure sensor is invalid ○ - - - - - -
The brake pedal stroke sensor assembly is invalid - ○ - - - - -
The power source voltage for all speed sensors is continuously low - - ○ - - - -
The voltage at terminal IG1 is excessively low - - - ○ - - -
The voltage at terminal IG2 is excessively low - - - - ○ - -
The relay contact is OFF continuously - - - - - ○ -
Motor fail-safe relay overcurrent continues - - - - - - ○
Detection Time 10 seconds or more. 10 seconds or more. 60 seconds or more. 10 seconds or more. 10 seconds or more. 1.22 seconds or more. 1.05 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C427347E07
5.042,0.969 5.49,1.344 0.448,0.375 10 false +BS 5.042,3.281 5.5,3.479 0.458,0.198 10 false GND1 4.74,0.708 5.052,0.906 0.313,0.198 10 false 14 4.792,3.135 5.125,3.302 0.333,0.167 10 false 1 4.844,4.042 6.76,4.479 1.917,0.438 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 4.844,3.875 5.26,4.052 0.417,0.177 10 false A6 3.427,1.021 4.156,1.271 0.729,0.25 10 false ABS NO. 2 1.198,0.813 3.031,1.26 1.833,0.448 10 false from Auxiliary Battery 1.604,1.656 3.271,2.073 1.667,0.417 10 false from IG Circuit 4.729,1.521 5.063,1.719 0.333,0.198 10 false 45 5.052,1.792 5.5,2.073 0.448,0.281 10 false IG1 3.375,2.656 4.438,2.99 1.063,0.333 10 false IG2 D NO. 4 5.052,2.604 5.5,2.885 0.448,0.281 10 false IG2 4.729,2.333 5.063,2.531 0.333,0.198 10 false 15 3.344,1.844 4.406,2.177 1.063,0.333 10 false IG1 D NO. 3 1.604,2.458 3.271,2.875 1.667,0.417 10 false from IG Circuit 6,1.656 6.313,1.854 0.313,0.198 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the auxiliary battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-45 (IG1) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-15 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-14 (+BS) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-1 (GND1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CLEAR DTC

Pre-procedure1

a.

Reconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C137BA2 is not output A
C137BA2 is output B



Post-procedure1

a.

None



A

B