Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for LHD)
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0454011 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A479058N18
6.417,0.167 6.917,0.167 false 1.698,0.813 2.146,0.813 false 5.948,0.042 6.604,0.5 0.656,0.458 18 false 1, 2 1.521,0.698 1.896,1.135 0.375,0.438 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 PERFORM ACCUMULATOR PRESSURE ZERO DOWN - (Click here) - -
3 SERVICE PLUG GRIP G3834 - - -

A481588N07
5.24,1.781 6.323,2.01 1.083,0.229 0.958,1.844 0.958,1.271 false 2.646,2.708 2.646,2.135 false 4.885,2.531 5.167,2.417 5.167,2.417 5.417,2.417 false 6.51,0.219 6.833,0.219 false 4.563,2.063 4.563,1.896 4.563,1.896 5.229,1.896 false 4.865,2.063 4.865,1.896 false 2.396,4.969 4.979,4.969 true 2.188,4.854 2.469,5.208 0.281,0.354 18 false 6 2.573,2.771 2.854,3.125 0.281,0.354 18 false 4 0.875,1.938 1.156,2.292 0.281,0.354 18 false 5 4.094,0.969 4.375,1.323 0.281,0.354 10 false x 6 5.531,3.115 5.813,3.469 0.281,0.354 10 false x 2 5.75,2.302 6.302,2.677 0.552,0.375 18 false 7, 9 6.323,0.115 6.604,0.469 0.281,0.354 18 false 8 5.333,1.833 6.448,2.073 1.115,0.24 8 false 8.0 (82, 71 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

4 UPPER RADIATOR SUPPORT SEAL 53292A - - -
5 FC STACK COVER SUB-ASSEMBLY 1A906 - - -
6 FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) G9200A (Click here) - -
7 REMOVE CONNECTOR COVER ASSEMBLY - (Click here) - -
8 CHECK TERMINAL VOLTAGE - (Click here) - -
9 INSTALL CONNECTOR COVER ASSEMBLY - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

C448780N01
6.354,0.229 6.854,0.229 false 4.417,0.917 4.417,0.5 4.417,0.5 4.75,0.5 false 2,1.5 2,1.833 2,1.833 2.25,1.833 false 1.083,1.5 1.083,1.25 1.083,1.25 1.25,1.25 false 0.531,3.781 0.948,3.781 false 2.667,1.219 2.667,1.052 2.667,1.052 2.5,1.052 false 2,4.25 2.333,4.25 false 6.052,0.104 6.552,0.542 0.5,0.438 18 false 10 4.802,0.375 5.333,0.781 0.531,0.406 18 false 11 2.385,4.125 2.802,4.49 0.417,0.365 18 false 12 2.583,1.74 2.917,2.156 0.333,0.417 18 false 13 1.302,1.125 1.677,1.542 0.375,0.417 18 false 14 0.208,3.656 0.542,4.073 0.333,0.417 18 false 15 2.167,0.917 2.583,1.25 0.417,0.333 18 false 16 1.333,3.031 1.75,3.281 0.417,0.25 10 false x 2 2.76,0.667 3.177,0.917 0.417,0.25 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

10 DRAIN BRAKE FLUID - - (Click here) -
11 COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY 55708 - - -
12 FENDER APRON BRACE SUB-ASSEMBLY LH 53706A - - -
13 FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) G9200A (Click here) - -
14 COOLER BRACKET - - - -
15 RELAY BLOCK - - - -
16 WIRE HARNESS CLAMP BRACKET - - - -

C448782N01
3.719,2.167 3.969,2.167 false 0.917,1.833 1.167,1.833 1.167,1.833 1.167,2.083 false 1.51,0.49 1.51,0.99 1.51,0.99 1.76,0.99 false 0.917,0.333 1.167,0.333 1.167,0.333 1.167,0.667 false 3.875,1 4.292,1 false 6.135,2.125 6.385,2.125 false 6,2.875 6.333,2.875 false 4.26,2.052 4.76,2.385 0.5,0.333 18 false 17 0.573,1.708 1.073,2.042 0.5,0.333 18 false 18 0.573,0.229 1.156,0.563 0.583,0.333 18 false 20 2.115,0.906 2.365,1.156 0.25,0.25 10 false ● 2.271,0.865 2.771,1.198 0.5,0.333 18 false 19 4.625,0.885 5.208,1.219 0.583,0.333 18 false 21 6.677,2.01 7.104,2.344 0.427,0.333 18 false 22 6.688,2.75 7.115,3.083 0.427,0.333 18 false 23 5.188,2.219 5.521,2.469 0.333,0.25 10 false x 2 5.99,1.229 6.323,1.479 0.333,0.25 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

17 FRONT COMPARTMENT MAIN WIRE 82111C (Click here) - -
18 REMOVE BRAKE TUBE - (Click here) - -
19 BRAKE TUBE CLAMP - (Click here) - -
20 DISCONNECT BRAKE TUBE - (Click here) - -
21 BRAKE ACTUATOR WITH BRACKET - (Click here) - -
22 NO. 5 BRAKE ACTUATOR BRACKET 44595 (Click here) - -
23 NO. 3 BRAKE ACTUATOR BRACKET 44593 (Click here) - -

● Non-reusable part - -

C448785N01
3.333,0.5 6.167,4.667 2.833,4.167 1.5,0.958 1.75,0.958 false 4.458,3.75 4.917,3.75 true 3.896,3.948 3.896,3.563 3.896,3.563 5.063,3.563 true 4.667,3.979 4.917,3.979 4.917,3.979 4.917,3.563 false 3.896,3.385 3.896,3.083 3.896,3.083 5.063,3.083 true 4.667,3.417 4.917,3.417 4.917,3.417 4.917,3.083 false 4.438,3.25 4.917,3.25 true 6.167,1.083 6.417,1.083 false 5.083,1.417 5.333,1.417 false 4.75,2.656 4.75,2.406 4.75,2.406 5,2.406 false 1.198,0.833 1.698,1.167 0.5,0.333 18 false 24 5.417,3.438 5.917,3.771 0.5,0.333 18 false 25 5.417,2.938 5.917,3.271 0.5,0.333 18 false 26 5.875,2.292 6.292,2.542 0.417,0.25 10 false x 4 6.469,1.021 6.885,1.271 0.417,0.25 10 false *1 5.385,1.354 5.802,1.604 0.417,0.25 10 false *2 5.052,2.344 5.469,2.594 0.417,0.25 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

24 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -
25 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A (Click here) - -
26 BRAKE ACTUATOR BRACKET CUSHION 44547B (Click here) - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY *2 NO. 1 BRAKE ACTUATOR BRACKET
*3 NO. 2 BRAKE ACTUATOR BRACKET - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
No. 2 skid control ECU (brake actuator assembly) Update ECU security key Vehicle control history (RoB) are stored (Click here)
1.

Bleed air

2.

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system disabled or malfunctions


(Click here)
·

Perform "EPB Initalize"

·

Acquire tension sensor zero point


Electric parking brake system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -



CAUTION / NOTICE / HINT

NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

a.
C441118N02
0.417,0.063 0.698,0.417 0.281,0.354 18 false i

i.

Using the GTS, perform the accumulator pressure zero down operation.

1. Select "Motor Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 3617

2. Perform "Motor Deactivate" according to the display on the GTS.

3. Select "ECB Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 3617

4. Perform "ECB Deactivate" according to the display on the GTS.

5. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.


6. Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.


7. Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
C453319N01
0.521,0.042 0.802,0.396 0.281,0.354 18 false i

i.

When the accumulator pressure zero down could not be performed using the GTS.

NOTICE:

If DTCs are output, the accumulator pressure zero down operation may not be complete. In this case, perform the following procedure.


1. With the ignition switch off, disconnect the brake master cylinder with pump assembly connector.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.


2. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

3. Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.


4. Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 53292A 4.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 1A906 5.REMOVE FC STACK COVER SUB-ASSEMBLY

Hide G9200A 6.DISCONNECT FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY)

Z101186

Click here(Click here)

Hide 7.REMOVE CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 8.CHECK TERMINAL VOLTAGE

Z101186

Click here(Click here)

Hide 9.INSTALL CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 10.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 55708 11.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53706A 12.REMOVE FENDER APRON BRACE SUB-ASSEMBLY LH

a.
C453028


Hide G9200A 13.DISCONNECT FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY)

Z101186

CAUTION:

Wear insulated gloves.



a.
C451687


Hide 14.REMOVE COOLER BRACKET

a.
C451688


Hide 15.DISCONNECT RELAY BLOCK

a.
C448786


Hide 16.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C448787


Hide 82111C 17.DISCONNECT FRONT COMPARTMENT MAIN WIRE

a.
C448788C01
0.5,0.042 0.75,0.375 0.25,0.333 18 true i 3.99,0.042 4.24,0.375 0.25,0.333 18 true ii
V113147

Release the lock lever
V113148

Disconnect the connector


i.

Disconnect the brake master cylinder with pump assembly connector.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




Hide 18.REMOVE BRAKE TUBE

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.




a.
C453656C01
4.563,0.656 4.979,0.406 4.979,0.406 5.146,0.406 true 4.729,0.896 5.063,0.979 5.063,0.979 5.229,0.979 true 4.083,1.313 4.25,1.313 4.25,1.313 4.417,0.896 true 4.021,1.052 4.271,1.052 4.271,1.052 4.354,0.802 true 3.958,0.854 4.208,0.854 4.208,0.854 4.292,0.688 true 3.719,0.625 4.219,0.625 true 5.198,0.354 5.615,0.604 0.417,0.25 10 false *a 5.281,0.917 5.615,1.167 0.333,0.25 10 false *b 3.896,1.25 4.146,1.417 0.25,0.167 10 true *c 3.844,0.979 4.094,1.146 0.25,0.167 10 true *d 3.792,0.771 4.042,0.938 0.25,0.167 10 true *e 3.573,0.563 3.823,0.729 0.25,0.167 10 true *f 0.417,0.042 0.75,0.375 0.333,0.333 18 false i
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Disc Brake Cylinder Assembly RH *d To Front Disc Brake Cylinder Assembly LH
*e To Rear Disc Brake Cylinder Assembly RH *f To Rear Disc Brake Cylinder Assembly LH


i.

Use tags or make a memo to identify the places to reconnect the brake tubes.



b.
C453657N01
0.417,0.052 1,0.385 0.583,0.333 18 false i, ii

i.

Using a union nut wrench, disconnect the 4 brake tubes from the brake actuator assembly and brake booster with master cylinder assembly.


ii.

Disengage the 2 clamps and remove the 2 brake tubes from the brake tube clamp.



Hide 19.REMOVE BRAKE TUBE CLAMP

Z101186

NOTICE:

Do not kink or damage the brake tubes.



a.
C448791


Hide 20.DISCONNECT BRAKE TUBE

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.




a.
C448792N01
0.417,0.052 0.75,0.469 0.333,0.417 18 false i

i.

Using a union nut wrench, disconnect the 4 brake tubes from the brake actuator assembly.



Hide 21.REMOVE BRAKE ACTUATOR WITH BRACKET

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator with bracket by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake tubes.



a.
C448794


Hide 44595 22.REMOVE NO. 5 BRAKE ACTUATOR BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 5 brake actuator bracket is necessary.



a.
C448796


Hide 44593 23.REMOVE NO. 3 BRAKE ACTUATOR BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 3 brake actuator bracket is necessary.



a.
C448798


Hide 44510 24.REMOVE BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C448799


Hide 44521A 25.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

Z101186

HINT:

Perform this procedure only when replacement of the No. 1 brake actuator case collars is necessary.



a.
C448801


Hide 44547B 26.REMOVE BRAKE ACTUATOR BRACKET CUSHION

Z101186

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.



a.
C448802