Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C05201C  Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range  C05202A  Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range  C052096  Multi-axis Acceleration Sensor Module "A" Component Internal Failure  


DESCRIPTION

The airbag ECU assembly has a built-in yaw rate and acceleration sensor.

These DTCs are stored when the No. 2 skid control ECU (brake actuator assembly) receives an internal malfunction signal from the yaw rate and acceleration sensor (airbag ECU assembly).

The No. 2 skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, DTC U012587 is output. When DTC U012587 is output together with C05201C, C05202A and/or C052096, inspect and repair the trouble areas indicated by U012587 first.


DTCs may be stored if either of the following occurs:

·

Yaw rate and acceleration sensor (airbag ECU assembly) installation abnormality.

·

Yaw rate and acceleration sensor (airbag ECU assembly) signal malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C05201C Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed sensor exceeds 0.35 G for 60 seconds or more.
·

Acceleration sensor (airbag ECU assembly) installation

·

Acceleration sensor (airbag ECU assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)
C05202A Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range Any of the following is detected:
·

The acceleration sensor output value does not change 16 times or more as the vehicle speed drops from 30 km/h (19 mph) to 0 km/h (0 mph).

·

A GL1 stuck malfunction status continues.

·

A GL2 stuck malfunction status continues.


·

Acceleration sensor (airbag ECU assembly) installation

·

Acceleration sensor (airbag ECU assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)
C052096 Multi-axis Acceleration Sensor Module "A" Component Internal Failure Either of the following is detected:
·

A signal indicating an acceleration sensor internal malfunction is received

·

Output values of GL1 and GL2 (front and rear, left and right) are outside permitted output range for 60 seconds or more.


·

Acceleration sensor (airbag ECU assembly) installation

·

Acceleration sensor (airbag ECU assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

C05202A DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status The acceleration sensor output value does not change 16 times or more as the vehicle speed drops from 30 km/h (19 mph) to 0 km/h (0 mph) ○ - -
A GL1 stuck malfunction status continues - ○ -
A GL2 stuck malfunction status continues - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C052096 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status A signal indicating an acceleration sensor internal malfunction is received ○ -
Output values of GL1 and GL2 (front and rear, left and right) are outside permitted output range - ○
Detection Time - 60 seconds or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the yaw rate and acceleration sensor (airbag ECU assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK AIRBAG ECU ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag ECU assembly) has been installed properly.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION


OK:

The yaw rate and acceleration sensor (airbag ECU assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag ECU assembly) is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

NG