Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C14C616  Electronic Brake Booster Control Module "A" Supply Voltage Circuit Voltage Below Threshold  


DESCRIPTION

Refer to DTC C110E14.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C110E14

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C14C616 Electronic Brake Booster Control Module "A" Supply Voltage Circuit Voltage Below Threshold Either of the following is detected:
·

Any of the following is detected when the ECU internal voltage is 6.92 V or less:

-

When operation of the main relay is requested, the relay output voltage is less than a certain value for 10.05 seconds or more.

-

The stroke sensor value invalid for 10.2 seconds or more.

-

The reaction force pressure sensor value invalid for 10.2 seconds or more.

-

The voltage supplied to the servo pressure sensor is a certain value or less or a certain value or more for 10.06 seconds or more.

-

The servo pressure sensor value invalid for 10.2 seconds or more.

-

The voltage supplied to the reaction force pressure sensor is a certain value or less or a certain value or more for 10.06 seconds or more.


·

When the internal voltage of the ECU is 8.3 V or less, the accumulator pressure sensor value is invalid for 10.8 seconds or more.


·

Improperly connected connector, deformation or corrosion of terminals

·

Wire harness and connector

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

C14C616 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnosis Condition When the ECU internal voltage is 6.92 V or less ○ ○ ○ ○ ○
Malfunction Status When operation of the main relay is requested, the relay output voltage is less than a certain value ○ - - - -
The stroke sensor value invalid - ○ - - -
The reaction force pressure sensor value invalid - - ○ - -
The voltage supplied to the servo pressure sensor is a certain value or less - - - ○ -
The voltage supplied to the servo pressure sensor is a certain value or more - - - - ○
Detection Time 10.05 seconds or more. 10.2 seconds or more. 10.2 seconds or more. 10.06 seconds or more. 10.06 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C14C616 DTC Detection Conditions
Vehicle Condition
Pattern 6 Pattern 7 Pattern 8 Pattern 9
Diagnosis Condition When the ECU internal voltage is 6.92 V or less ○ ○ ○ -
When the internal voltage of the ECU is 8.3 V or less - - - ○
Malfunction Status The servo pressure sensor value invalid ○ - - -
The voltage supplied to the reaction force pressure sensor is a certain value or less - ○ - -
The voltage supplied to the reaction force pressure sensor is a certain value or more - - ○ -
The accumulator pressure sensor value is invalid - - - ○
Detection Time 10.2 seconds or more. 10.06 seconds or more. 10.06 seconds or more. 10.8 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the auxiliary battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
Only C14C616 is output A
C14C616 and other DTCs are output B



A

2.CHECK DTC

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK HARNESS AND CONNECTOR (IG1, +BI1 AND BS TERMINAL)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (IG1, +BI1 AND BS TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure3

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A5)Location & Routing

Click Connector(A5)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster with Master Cylinder Assembly

A5-31 (IG1) - Body ground Ignition switch ON 11 to 14 V
A5-14 (+BI1) - Body ground Ignition switch ON 11 to 14 V
A5-15 (BS) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR