Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C13DA00  Brake Pressure Too High (Brake Booster)  


DESCRIPTION

Refer to DTCs C139A00, C13D900 and C14EC7E.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C139A00

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C13DA00 Brake Pressure Too High (Brake Booster) Fluid pressure control performance degraded (pressure excessively high)
·

Foreign matter in solenoid valve

·

Wire harness and connector

·

Brake booster with master cylinder assembly


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA

Pre-procedure1

a.

Interview the customer to check the vehicle conditions when the brake system warning light (yellow indicator) illuminated.


Procedure1

a.

Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.

Chassis > Brake Booster > Trouble Codes
50001 466
HINT:

Freeze Frame Data is only stored once when a DTC is stored.


Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

2.CLEAR DTC
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.CHECK DTC
3.CHECK DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
Only C13DA00 is output A
C13DA00 and other DTCs are output B



Post-procedure1

a.

None



A

4.CHECK DTC

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

4.CHECK DTC

Pre-procedure1

a.

None


Procedure1

a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

Turn the ignition switch off.



A

5.CLEAR DTC

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

6.PERFORM AIR BLEEDING
6.PERFORM AIR BLEEDING
HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


Result:
Proceed to
NEXT



NEXT

7.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (ACTUATOR SIDE)
7.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (ACTUATOR SIDE)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

After 3 minutes elapse after turning the ignition switch off, disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

Pre-procedure1

a.

Reconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure1

a.

Measure the voltage and resistance on the wire harness side.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU


OK:

Voltage and resistance readings are all normal.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

9.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
HINT:

If the system returns to normal, it is suspected that a DTC was stored due to a poor connection of a terminal in a connector or foreign matter in a solenoid valve, etc.


Result:
Result Proceed to
C13DA00 is not output A
C13DA00 is output B



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY