Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C05061F  Right Front Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

Refer to DTC C050612.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050612

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C05061F Right Front Wheel Speed Sensor Circuit Intermittent Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor RH (front axle hub sub-assembly RH)

·

Speed sensor installation

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

C05061F DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more ○ - -
At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation - - ○
Detection Time - - 15 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (FR WHEEL SPEED AND MOMENTARY INTERRUPTION)
a.

While monitoring the values of the Data List, perform a road test and attempt to reproduce the problem symptoms based on the interview with the customer and the vehicle conditions stored as Freeze Frame Data when the DTC was stored.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
FR Speed Open Front speed sensor RH open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake/EPB > Data List
Tester Display
FR Wheel Speed
FR Speed Open
50003 435 13,101
OK:

The values change in accordance with the operation of the vehicle and there is no intermittent operation.


NOTICE:

Perform the above inspection before removing the sensor and connector.


HINT:

The front speed sensor rotor RH and front speed sensor RH are incorporated into the front axle hub sub-assembly RH.

If the front speed sensor RH and front speed sensor rotor RH needs to be replaced, replace the front axle hub sub-assembly RH.



Result:
Proceed to
OK
NG



OK

NG

REPLACE FRONT AXLE HUB SUB-ASSEMBLY RH