Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C050612  Right Front Wheel Speed Sensor Circuit Short to Battery  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the No. 2 skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the No. 2 skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and No. 2 skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C435283E01
3.646,0.875 4.51,1.427 4.51,1.427 4.74,1.427 true 2.229,3.469 2.906,3.667 0.677,0.198 10 false Backward 3.01,3.469 3.708,3.688 0.698,0.219 10 false Forward 3.042,1.896 4.5,2.156 1.458,0.26 10 false Speed Sensor Rotor 4.313,0.26 4.938,0.5 0.625,0.24 10 false Forward 2.385,0.25 3.042,0.448 0.656,0.198 10 false Backward 4.781,1.344 5.802,1.573 1.021,0.229 10 false Speed Sensor 4.094,3.281 4.885,3.469 0.792,0.188 10 false Low speed 5.25,3.26 6.073,3.479 0.823,0.219 10 false High speed 6.49,2.74 7.073,2.927 0.583,0.188 10 false 0.7 V 6.479,2.479 7.042,2.667 0.563,0.188 10 false 1.4 V 6.479,2.229 7.042,2.396 0.563,0.167 10 false 2.6 V

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C050612 Right Front Wheel Speed Sensor Circuit Short to Battery The speed sensor short signal is ON continuously for 0.5 seconds or more.
·

Front speed sensor RH (front axle hub sub-assembly RH)

·

Front skid control sensor wire RH

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C449381E05
5.792,1.25 6.292,1.417 0.5,0.167 10 false FR+ 1.188,1.115 1.625,1.281 0.438,0.167 10 false FR+ 1.188,1.833 1.625,2.021 0.438,0.188 10 false FR- 5.813,1.802 6.271,2 0.458,0.198 10 false FR- 5.125,2.875 5.625,3.073 0.5,0.198 10 false A6 5.125,3.063 7.052,3.552 1.927,0.49 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.594,1.01 5.76,1.302 0.167,0.292 10 false 7 5.604,1.688 5.771,2.021 0.167,0.333 10 false 6 1.688,0.865 2.073,1.135 0.385,0.271 10 false 2 1.688,1.594 2.042,1.865 0.354,0.271 10 false 1 1.625,1.813 2.063,2 0.438,0.188 10 false W2 3.177,1.125 3.615,1.313 0.438,0.188 10 false AW2 1.99,2.271 3.458,2.771 1.469,0.5 10 false Front Skid Control Sensor Wire RH 0.198,2.24 1.781,2.865 1.583,0.625 10 false Front Speed Sensor RH (Front Axle Hub Sub-assembly RH) 1.615,1.125 2.052,1.313 0.438,0.188 10 false W2 3.177,1.813 3.615,2 0.438,0.188 10 false AW2 3.281,1.594 3.635,1.865 0.354,0.271 10 false 1 3.281,0.885 3.667,1.156 0.385,0.271 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the W2 front skid control sensor wire RH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(W2)Location & Routing

Click Connector(W2)Engine Compartment>Front Skid Control Sensor Wire LH / Front Skid Control Sensor Wire RH>Front Speed Sensor RH (Front Axle Hub Sub-Assembly RH)

W2-2 (FR+) - W2-1 (FR-) Ignition switch ON 11 to 14 V


HINT:

The front speed sensor rotor RH and front speed sensor RH are incorporated into the front axle hub sub-assembly RH.

If the front speed sensor RH and front speed sensor rotor RH needs to be replaced, replace the front axle hub sub-assembly RH.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT AXLE HUB SUB-ASSEMBLY RH

NG

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the AW2 front skid control sensor wire RH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure3

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(AW2)Location & Routing

Click Connector(AW2)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Compartment Main Wire and Front Skid Control Sensor Wire RH

AW2-5 - AW2-1 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT SKID CONTROL SENSOR WIRE RH

Click here


NG

3.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(AW2)Location & Routing

Click Connector(AW2)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Compartment Main Wire and Front Skid Control Sensor Wire RH

AW2-1 - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (FRONT SKID CONTROL SENSOR WIRE RH - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT SKID CONTROL SENSOR WIRE RH - BRAKE ACTUATOR ASSEMBLY)

Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR