Refer to DTC C051212.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C051212
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| C051223 | Right Rear Wheel Speed Sensor Signal Stuck Low | Any of the following is detected:
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h or more, output from the 2 speed sensors is 0 km/h (0 mph) for a total of 200 seconds. |
·
Rear speed sensor RH ·
Rear speed sensor installation ·
Rear skid control sensor wire RH ·
Wire harness and connector ·
Rear speed sensor rotor RH (rear axle hub and bearing assembly RH) |
Brake/EPB | A | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | When the +BS terminal voltage is 17.4 V or less | ○ | ○ | ○ |
| Malfunction Status | At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors | ○ | - | - |
| At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) | - | ○ | - | |
| At a vehicle speed of 10 km/h (6 mph) or more, outputs from the 2 speed sensors is 0 km/h (0 mph) | - | - | ○ | |
| Detection Time | 30 seconds or more. | 1 second or more. | Total of 200 seconds. | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
Refer to DTC C051212.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C051212
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
| *a | Correct |
| *b | Incorrect |
Check the rear speed sensor RH installation.
There is no clearance between the rear speed sensor RH and the rear axle carrier RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the rear speed sensor RH.
Procedure1
Check the rear speed sensor tip RH.
The rear speed sensor tip RH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the rear speed sensor RH, clean the rear speed sensor RH.
If the rear speed sensor RH is damaged, replace the rear speed sensor RH with a new one.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Perform a road test.
Procedure1
Check the rear speed sensor RH output value.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RR Wheel Speed |
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the WG1 rear skid control sensor wire RH connector.
Disconnect the W4 rear skid control sensor wire RH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(W4,WG1)Location & Routingewd_type=routing;type=c,w;code=W4,WG1 Click Connector(W4)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Speed Sensor RHewd_type=component;type=c;code=W4;pinno=2,1 Click Connector(WG1)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Skid Control Sensor Wire RH and Floor Wireewd_type=component;type=w;code=WG1;pinno=3,4 |
||
| W4-2 (RR+) - WG1-3 | Always | Below 1 Ω |
| W4-2 (RR+) or WG1-3 - Body ground and other terminals | Always | 10 kΩ or higher |
| W4-1 (RR-) - WG1-4 | Always | Below 1 Ω |
| W4-1 (RR-) or WG1-4 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A6,WG1)Location & Routingewd_type=routing;type=c,w;code=A6,WG1 Click Connector(WG1)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Skid Control Sensor Wire RH and Floor Wireewd_type=component;type=w;code=WG1;pinno=3,4 |
||
| A6-20 (RR+) - WG1-3 | Always | Below 1 Ω |
| A6-20 (RR+) or WG1-3 - Body ground | Always | 10 kΩ or higher |
| A6-19 (RR-) - WG1-4 | Always | Below 1 Ω |
| A6-19 (RR-) or WG1-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the component with the rear speed sensor rotor RH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL
Procedure1
Check the rear speed sensor rotor RH.
The rear speed sensor rotor RH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the rear speed sensor rotor RH, clean the rear speed sensor rotor RH.
Do not use parts cleaner when cleaning the rear speed sensor rotor RH.
If the rear speed sensor rotor RH is damaged, replace the rear speed sensor rotor RH with a new one.
The rear speed sensor rotor RH is incorporated into the rear axle hub and bearing assembly RH.
If the rear speed sensor rotor RH needs to be replaced, replace it together with the rear axle hub and bearing assembly RH.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The rear speed sensor rotor RH is damaged.) | B |
| NG (There is foreign matter on the rear speed sensor rotor RH.) | C |
Post-procedure1
None
A
B
C