Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB
RM37H0E _52 Drivetrain _095769 AXLE AND DIFFERENTIAL _0452040 REAR AXLE HUB A

AXLE AND DIFFERENTIAL  REAR AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C447780N05
4.552,2.938 4.917,2.938 true 3.146,2.5 3.375,2.5 true 4.906,3.521 5.135,3.521 true 1.375,3.917 1.75,3.917 true 1.417,4.75 1.792,4.75 true 3.469,4.375 3.552,4.771 3.552,4.771 3.719,4.771 true 6.5,3.25 6.333,3.25 6.333,3.25 6.167,3.667 true 5.583,1.938 5.5,1.74 5.5,1.74 5.375,1.74 true 5.667,1.167 5.583,0.917 5.583,0.917 5.417,0.917 true 6.531,0.167 6.896,0.167 true 6.51,0.615 6.844,0.615 true 6.302,0.063 6.583,0.333 0.281,0.271 18 false 1 0.833,0.25 1.146,0.448 0.313,0.198 10 false x 2 6.313,0.479 6.594,0.75 0.281,0.271 18 false 2 5.219,0.802 5.5,1.073 0.281,0.271 18 false 7 5.208,1.604 5.49,1.875 0.281,0.271 18 false 8 5.229,2.823 5.573,3.125 0.344,0.302 18 false 11 6.573,3.115 6.854,3.385 0.281,0.271 18 false 3 5.198,3.396 5.531,3.667 0.333,0.271 18 false 10 3.688,2.396 4,2.719 0.313,0.323 18 false 6 4.042,4.635 4.354,4.958 0.313,0.323 18 false 9 1.219,4.594 1.531,4.917 0.313,0.323 18 false 5 1.833,3.771 2.146,4.094 0.313,0.323 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - (Click here)
3 REAR WHEEL - - - -
4 REAR STABILIZER LINK ASSEMBLY LH 48840A - - -
5 REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH 89408C - - -
6 REAR AXLE SHAFT NUT LH 42312B (Click here) - -
7 REAR SKID CONTROL SENSOR WIRE LH 89516P (Click here) - -
8 REAR SPEED SENSOR LH 89546 (Click here) - -
9 REAR DISC BRAKE CYLINDER ASSEMBLY LH 47850 (Click here) - -
10 PARKING BRAKE SHOE ADJUSTING HOLE PLUG 42491 - - -
11 REAR DISC LH 42432 (Click here) - -

C446770N03
1.667,3.906 1.5,3.906 1.5,3.906 1.344,3.604 true 2.667,5.333 2.5,5.333 2.5,5.333 2.146,5.135 true 1.417,0.667 1.708,0.667 true 3.583,4.083 3.417,4.083 3.417,4.083 3.208,3.813 true 2.958,1.531 2.896,1.167 2.896,1.167 2.813,1.167 true 3,0.313 2.833,0.167 2.833,0.167 2.667,0.167 true 4.333,1.833 4.167,1.833 4.167,1.833 4.083,2.167 true 1.208,2.167 1.083,2.479 1.083,2.479 0.917,2.479 true 3.51,1.167 3.927,1.167 true 4,0.333 4.417,0.333 true 0.604,1 0.938,1 true 5.667,2.5 6.083,2.5 true 3.75,3.333 4.167,3.333 true 5.635,3.125 6,3.125 true 0.75,2.396 1.063,2.594 0.313,0.198 10 false *1 4.667,1.719 5.219,2.073 0.552,0.354 18 false 19 1.76,3.781 2.313,4.135 0.552,0.354 18 false 12 2,0.531 2.552,0.885 0.552,0.354 18 false 13 2.948,5.229 3.5,5.583 0.552,0.354 18 false 14 3.927,3.938 4.479,4.292 0.552,0.354 18 false 15 2.479,1.031 2.896,1.313 0.417,0.281 18 false 17 6.271,3.021 6.823,3.375 0.552,0.354 18 false 16 3.99,1.052 4.188,1.25 0.198,0.198 10 false ● 4.5,0.219 4.698,0.417 0.198,0.198 10 false ● 0.438,0.896 0.635,1.094 0.198,0.198 10 false ● 6.135,2.396 6.333,2.594 0.198,0.198 10 false ● 4.219,3.229 4.417,3.427 0.198,0.198 10 false ● 2.333,0.042 2.75,0.323 0.417,0.281 18 false 18

Procedure Part Name Code
Z101186

Z101188

Z101187

12 PARKING BRAKE - - - -
13 REAR SHOCK ABSORBER ASSEMBLY LH 48540 (Click here) - -
14 REAR NO. 2 SUSPENSION ARM ASSEMBLY LH 48740F (Click here) - -
15 LOWER CONTROL ARM ASSEMBLY LH 48730 (Click here) - -
16 TOE CONTROL LINK SUB-ASSEMBLY LH 48706B (Click here) - -
17 REAR NO. 1 SUSPENSION ARM ASSEMBLY LH 48720A (Click here) - -
18 REAR UPPER CONTROL ARM ASSEMBLY LH 48790 (Click here) - -
19 REAR AXLE ASSEMBLY - (Click here) - -

*1 REAR DRIVE SHAFT ASSEMBLY LH - -
● Non-reusable part - -

C449467N02
0.396,1 0.552,0.615 0.552,0.615 0.719,0.615 true 2.76,1.25 2.969,0.875 2.969,0.875 3.135,0.875 true 4.833,2.229 5.021,1.917 5.021,1.917 5.188,1.917 true 5.229,4.99 5.396,4.99 5.396,4.99 5.458,4.667 true 6.729,3.844 6.563,3.844 6.563,3.844 6.448,4.229 true 1.292,4.125 1.125,4.125 1.125,4.125 1.042,3.833 true 1.198,0.49 1.688,0.833 0.49,0.344 18 false 20 6.781,3.698 7.094,4.042 0.313,0.344 18 false 21 5.052,4.906 5.313,5.146 0.26,0.24 10 false *2 5.25,1.823 5.563,2.021 0.313,0.198 10 false *1 3.219,0.719 3.635,1.052 0.417,0.333 18 false 22 1.354,4.021 1.667,4.219 0.313,0.198 10 false *3 0.76,3.052 1.073,3.25 0.313,0.198 10 false x 2 1.208,1.313 1.521,1.51 0.313,0.198 10 false x 4 1.052,0.531 1.208,0.729 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

20 REAR NO. 1 WHEEL BEARING DUST DEFLECTOR LH 42451B (Click here) - -
21 REAR AXLE HUB AND BEARING ASSEMBLY LH 42450B - - -
22 REAR AXLE CARRIER SUB-ASSEMBLY LH 42305 - - -

*1 PARKING BRAKE PLATE *2 PARKING BRAKE ANCHOR BLOCK SUB-ASSEMBLY
*3 CABLE SUPPORT BRACKET - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear axle hub removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

Rear wheel alignment adjustment Perform "Calibration" VSC malfunctioning (Click here)
Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
·

Rear disc (Including removal and installation)

·

Parking brake shoe (Including removal and installation)


Parking brake bedding Electric parking brake system (Click here)
Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. Have been performed Perform headlight ECU sub-assembly LH initialization
·

Automatic headlight beam level control system

·

Adaptive high beam system


(Click here)
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 3.REMOVE REAR WHEEL

Hide 48840A 4.DISCONNECT REAR STABILIZER LINK ASSEMBLY LH

Hide 89408C 5.DISCONNECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

Hide 42312B 6.REMOVE REAR AXLE SHAFT NUT LH

a.
C449416N01
2.979,1.292 3.229,1.292 true 3.281,1.219 3.74,1.417 0.458,0.198 10 false SST 1.25,0.167 1.583,0.5 0.333,0.333 18 false i 2.031,2.177 2.365,2.51 0.333,0.333 18 false ii

i.

Using SST and a hammer, release the staked part of the rear axle shaft nut LH.

SST
09930-00010  

NOTICE:
·

Set SST in the groove with its flat surface facing upward.

·

Do not grind the tip of SST with a grinder or other tools.

·

Fully unstake the rear axle shaft nut LH.

·

Do not damage the threads of the rear drive shaft assembly LH.




ii.

Using a 32 mm socket wrench, remove the rear axle shaft nut LH.



Hide 89516P 7.DISCONNECT REAR SKID CONTROL SENSOR WIRE LH

a.
C446774N01
0.417,0.052 0.698,0.406 0.281,0.354 18 true i 4.125,1.01 4.365,1.302 0.24,0.292 18 true ii

i.

Disconnect the speed sensor connector from the speed sensor LH.

NOTICE:
·

Be careful not to damage the rear speed sensor LH.

·

Prevent foreign matter from adhering to the rear speed sensor LH.




ii.

Remove the bolt and disconnect the rear skid control sensor wire LH.



Hide 89546 8.REMOVE REAR SPEED SENSOR LH

Z101186

Click here(Click here)

Hide 47850 9.DISCONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C446775N01
0.375,0.031 0.656,0.385 0.281,0.354 18 false i

i.

Remove the 2 bolts and rear disc brake cylinder assembly LH from the rear axle carrier sub-assembly LH.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake cylinder assembly LH from hanging down by the flexible hose.




Hide 42491 10.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42432 11.REMOVE REAR DISC LH

Z101186

Click here(Click here)

Hide 12.REMOVE PARKING BRAKE

Hide 48540 13.DISCONNECT REAR SHOCK ABSORBER ASSEMBLY LH

a.
C447152C01
4.25,0.042 4.677,0.385 0.427,0.344 18 true ii 0.208,0.042 0.635,0.385 0.427,0.344 18 true i
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


i.

Remove the nut from the rear shock absorber assembly LH (lower side).


ii.

Remove the rear shock absorber assembly LH and washer as shown in the illustration.



Hide 48740F 14.DISCONNECT REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C446778C01
0.917,1.583 1.083,1.583 false 1.896,1.385 2.083,1.667 2.083,1.667 2.25,1.667 true 1.5,0.969 1.917,0.75 1.917,0.75 2,0.75 true 5.344,2.198 5.531,2.479 5.531,2.479 5.698,2.479 true 5.76,2.385 5.969,2.573 0.208,0.188 10 true *a 2.073,0.677 2.385,0.833 0.313,0.156 10 false *b 2.302,1.604 2.615,1.76 0.313,0.156 10 false *c 0.75,1.521 1.063,1.677 0.313,0.156 10 false *d 0.583,0.104 1.01,0.469 0.427,0.365 18 false i 2.188,3 2.615,3.365 0.427,0.365 18 false ii
*a A *b Arm
*c Slide Pin *d Rear Axle Carrier LH
V100135

Front of the Vehicle - -


i.

Loosen the bolt and nut. To avoid damaging the No. 2 rear suspension arm assembly LH, tap the part A with the plastic-faced hammer or similar tool from the rear of the vehicle and ensure slide pin clearance.

NOTICE:

Do not pry and remove the No. 2 rear suspension arm assembly LH.



ii.

Remove the bolt, washer and nut, and disconnect the No. 2 rear suspension arm assembly LH from the rear axle carrier LH.



Hide 48730 15.DISCONNECT LOWER CONTROL ARM ASSEMBLY LH

a.
C446781C01
6.146,2.771 6.417,2.417 6.417,2.417 6.583,2.417 true 2.583,3.26 2.917,3.26 true 5.021,2.927 4.75,2.5 4.75,2.5 4.583,2.5 true 5.094,3.188 4.948,3.438 4.948,3.438 5.135,3.26 true 5.573,2.698 5.417,2.25 5.417,2.25 5.25,2.25 true 1.635,2.948 1.969,2.948 true 6,3.385 6.083,3.5 6.083,3.5 6.167,3.5 true 4.833,3.448 5.063,3.615 0.229,0.167 10 false *a 4.458,3.083 4.75,3.333 0.292,0.25 10 false *b 4.406,2.438 4.667,2.667 0.26,0.229 10 false *c 5.073,2.188 5.323,2.438 0.25,0.25 10 false *d 6.427,3.031 6.677,3.281 0.25,0.25 10 false *g 6.219,3.427 6.448,3.594 0.229,0.167 10 false *e 6.646,2.354 6.896,2.604 0.25,0.25 10 false *f 3.01,3.198 3.354,3.385 0.344,0.188 10 true SST 1.344,2.865 1.604,3.063 0.26,0.198 10 true *h 1.979,0.104 2.313,0.396 0.333,0.292 18 false i 0.49,2.031 0.927,2.323 0.438,0.292 18 true ii, iii
*a SST (Spacer B) *b 1 mm (0.0394 in.)
*c Spacer *d Center Nut
*e Body *f Claw
*g Parallel *h String


i.

Remove the nut.


ii.

Install 2 SST (spacer B) onto the lower control arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

SST
09960-20010  (09961-02060)

NOTICE:
·

Make sure to install the spacers (SST spacer B) as the rear axle carrier sub-assembly LH spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.




iii.

Using SST, disconnect the lower control arm assembly LH from the rear axle carrier sub-assembly LH.

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of SST bolt.

·

Do not damage the dust cover.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.





Hide 48706B 16.DISCONNECT TOE CONTROL LINK SUB-ASSEMBLY LH

a.
C446783C01
6.146,2.771 6.417,2.417 6.417,2.417 6.583,2.417 true 0.917,2.833 1.25,2.833 true 4.979,2.906 4.667,2.5 4.667,2.5 4.5,2.5 true 5.094,3.188 4.948,3.438 4.948,3.438 5.135,3.26 true 5.573,2.698 5.417,2.25 5.417,2.25 5.25,2.25 true 1.5,2.167 2.208,2.167 true 6,3.385 6.083,3.5 6.083,3.5 6.167,3.5 true 4.813,3.448 5.042,3.615 0.229,0.167 10 false *a 4.438,3.083 4.729,3.333 0.292,0.25 10 false *b 4.302,2.406 4.563,2.635 0.26,0.229 10 false *c 5.063,2.177 5.313,2.427 0.25,0.25 10 false *d 6.427,3.031 6.677,3.281 0.25,0.25 10 false *g 6.229,3.427 6.458,3.594 0.229,0.167 10 false *e 6.646,2.344 6.896,2.594 0.25,0.25 10 false *f 0.5,2.75 0.844,2.938 0.344,0.188 10 true SST 1.24,2.083 1.5,2.281 0.26,0.198 10 true *h 2.01,0.125 2.344,0.417 0.333,0.292 18 false i 0.583,2 1.073,2.302 0.49,0.302 18 true ii, iii
*a SST (Spacer B) *b 1 mm (0.0394 in.)
*c Spacer *d Center Nut
*e Body *f Claw
*g Parallel *h String


i.

Remove the nut.


ii.

Install 2 SST (spacer B) onto the toe control link sub-assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

SST
09960-20010  (09961-02060)

NOTICE:
·

Make sure to install the spacers (SST spacer B) as the rear axle carrier sub-assembly LH spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.




iii.

Using SST, disconnect the toe control link sub-assembly LH from the rear axle carrier sub-assembly LH.

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of SST bolt.

·

Do not damage the dust cover.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.





Hide 48720A 17.DISCONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C446785C02
6.281,2.75 6.417,2.417 6.417,2.417 6.583,2.417 true 1.417,2.583 1.75,2.583 true 5.063,2.885 4.833,2.5 4.833,2.5 4.667,2.5 true 5.135,3.177 4.948,3.438 4.948,3.438 5.177,3.219 true 5.635,2.677 5.417,2.25 5.417,2.25 5.25,2.25 true 1.958,2.115 2.375,2.115 true 6,3.385 6.083,3.5 6.083,3.5 6.167,3.5 true 4.813,3.427 5.042,3.594 0.229,0.167 10 false *a 4.531,3.052 4.823,3.302 0.292,0.25 10 false *b 4.49,2.417 4.75,2.646 0.26,0.229 10 false *c 5.063,2.177 5.313,2.427 0.25,0.25 10 false *d 6.469,3.01 6.719,3.26 0.25,0.25 10 false *g 6.229,3.427 6.458,3.594 0.229,0.167 10 false *e 6.646,2.344 6.896,2.594 0.25,0.25 10 false *f 1,2.5 1.344,2.688 0.344,0.188 10 true SST 1.656,2.01 1.917,2.208 0.26,0.198 10 true *h 2.031,0.125 2.365,0.417 0.333,0.292 18 false i 0.615,2 1.104,2.302 0.49,0.302 18 true ii, iii
*a SST (Spacer A) *b 1 mm (0.0394 in.)
*c Spacer *d Center Nut
*e Body *f Claw
*g Parallel *h String


i.

Remove the nut.


ii.

Install 2 SST (spacer A) onto the rear No. 1 suspension arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

SST
09960-20010  (09961-02050)

NOTICE:
·

Make sure to install the spacers (SST spacer A) as the rear axle carrier sub-assembly LH spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.




iii.

Using SST, disconnect the rear No. 1 suspension arm assembly LH from the rear axle carrier sub-assembly LH.

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of SST bolt.

·

Do not damage the dust cover.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.





Hide 48790 18.DISCONNECT REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C446787C02
6.188,2.75 6.417,2.417 6.417,2.417 6.583,2.417 true 2.521,2.75 2.854,2.75 true 5.167,2.896 4.938,2.51 4.938,2.51 4.771,2.51 true 5.229,3.156 5.042,3.417 5.042,3.417 5.271,3.198 true 5.615,2.708 5.417,2.24 5.417,2.24 5.25,2.24 true 1.26,2.125 1.677,2.125 true 5.969,3.344 6.052,3.458 6.052,3.458 6.135,3.458 true 4.917,3.406 5.146,3.573 0.229,0.167 10 false *a 4.698,3.063 4.99,3.313 0.292,0.25 10 false *b 4.583,2.448 4.844,2.677 0.26,0.229 10 false *c 5.063,2.177 5.313,2.427 0.25,0.25 10 false *d 6.385,3 6.635,3.25 0.25,0.25 10 false *g 6.188,3.396 6.417,3.563 0.229,0.167 10 false *e 6.646,2.344 6.896,2.594 0.25,0.25 10 false *f 2.948,2.688 3.292,2.875 0.344,0.188 10 true SST 1.656,2.01 1.917,2.208 0.26,0.198 10 true *h 2.031,0.083 2.365,0.375 0.333,0.292 18 false i 0.51,2.021 0.958,2.313 0.448,0.292 18 true ii, iii
*a SST (Spacer A) *b 1 mm (0.0394 in.)
*c Spacer *d Center Nut
*e Body *f Claw
*g Parallel *h String


i.

Remove the nut.


ii.

Install 2 SST (spacer A) onto the rear upper control arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

SST
09960-20010  (09961-02050)

NOTICE:
·

Make sure to install the spacers (SST spacer A) as the rear axle carrier sub-assembly LH spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.




iii.

Using SST, disconnect the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of SST bolt.

·

Do not damage the dust cover.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.





Hide 19.REMOVE REAR AXLE ASSEMBLY

a.
C446788C01
4.5,0.271 5.083,0.271 true 4.5,0.479 4.833,0.479 4.833,0.479 4.833,0.271 true 5.146,0.188 5.458,0.385 0.313,0.198 10 false *a 0.448,0.021 0.938,0.354 0.49,0.333 18 false ii, iii 3.802,0.094 3.958,0.375 0.156,0.281 18 true i
*a Matchmark - -


i.

Place matchmarks on the rear axle hub and bearing assembly LH and rear drive shaft assembly LH as shown in the illustration.


ii.

Using a plastic-faced hammer, lightly tap the end of the drive shaft assembly and disengage the drive shaft and rear axle carrier.

HINT:

If the connection is stiff, tap the end of the drive shaft using a brass bar and hammer.



iii.

Pull the rear axle assembly LH toward the vehicle exterior while supporting the rear drive shaft assembly.

NOTICE:
·

Do not damage the drive shaft outboard joint boot.

·

Suspend the drive shaft assembly with rope, wire or an equivalent tool.





Hide 42451B 20.REMOVE REAR NO. 1 WHEEL BEARING DUST DEFLECTOR LH

a.
C446789N01
0.396,0.042 0.677,0.396 0.281,0.354 18 false i

i.

Using a screwdriver, remove the rear No. 1 wheel bearing dust deflector LH from the rear axle carrier.

NOTICE:

The rear axle carrier is made from aluminum. Therefore, take care that it does not become dented.




Hide 42450B 21.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

a.
C446790


Hide 42305 22.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH

a.
C449463