Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C13B951  SM Valve Learning Not Programmed  C13B954  SM Valve Learning Missing Calibration  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) stores the individual characteristics of each linear solenoid built into the brake actuator assembly. Based on the stored information, the No. 2 skid control ECU (brake actuator assembly) calibrates the individual differences and controls systems.

The No. 2 skid control ECU (brake actuator assembly) receives the shift position P signal from the EV control ECU through the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C13B951 SM Valve Learning Not Programmed The SM solenoid valve offset learning value is not stored.
·

If this DTC is not output after performing SM solenoid valve offset learning, there is no malfunction.

·

Brake fluid leaks

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
HINT:

During Dealer Mode, related DTCs are cleared.


C13B954 SM Valve Learning Missing Calibration SM solenoid valve offset learning cannot be obtained
·

If this DTC is not output after performing SM solenoid valve offset learning, there is no malfunction.

·

Brake fluid leaks

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK DTC
a.

Check that no DTCs other than those related to incomplete learning are output.

Chassis > Brake/EPB > Trouble Codes
50001 435
OK:

DTCs other than those related to incomplete learning are not output.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR FLUID LEAK

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK FOR FLUID LEAK
a.

Inspect the following items for brake fluid leaks:

1.

Check and take a note of the fluid level in the brake master cylinder reservoir assembly.

2.

Repeatedly depress the brake pedal and confirm that the brake pedal feels normal (no air in the system, etc.).

3.

Check if the brake fluid level in the brake master cylinder reservoir assembly has changed.

4.

If the brake fluid level has decreased, check for leaks due to damaged brake lines or hoses, loose union nuts, damaged brake master cylinder sub-assembly seals, etc.



Result:
Proceed to
OK
NG



OK

3.PERFORM AIR BLEEDING

NG

REPAIR OR REPLACE APPLICABLE PART

3.PERFORM AIR BLEEDING
HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


Result:
Proceed to
NEXT



NEXT

4.PERFORM SM SOLENOID VALVE OFFSET LEARNING
4.PERFORM SM SOLENOID VALVE OFFSET LEARNING
a.

Check that the conditions required for SM solenoid valve offset learning are met and perform SM solenoid valve offset learning.

NOTICE:

If DTC C13B954 is output, wait 3 minutes or more with the ignition switch turned off, then perform learning after turning the ignition switch to ON and clearing the DTCs.


HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554
1.

The auxiliary battery voltage is 11 to 15.5 V when the ignition switch is ON (READY).

2.

The brake actuator assembly is not hot.

3.

The hybrid control system is not malfunctioning.

4.

The shift state indicator shows that park (P) is selected.

5.

The READY light in the combination meter assembly is illuminated.

6.

The brake pedal is not depressed.

7.

The parking brake is released.

8.

DTC C134551 is not output.



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C13B951 and C13B954 are not output A
C13B951 or C13B954 is output B



Post-procedure1

a.

None



A

B