This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna (main) which is connected to the radio receiver assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B157D | DAB (Digital Audio Broadcasting) Antenna Disconnected | The digital audio broadcasting antenna (main) is not connected | ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
Digital audio broadcasting antenna assembly LH ·
Back window glass (window glass antenna wire) ·
Radio receiver assembly |
Navigation System | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Check if the digital audio broadcasting antenna cable is securely connected to the radio receiver assembly.
Digital audio broadcasting antenna cable is securely connected
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Tester Probe |
| *b | Antenna Wire |
| *c | Tin Foil |
Check for continuity in the window glass antenna wire.
When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.
Check for continuity at the center of each antenna wire as shown in the illustration.
There is continuity in the window glass antenna wire.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the antenna connector from the radio receiver assembly.
Disconnect the antenna connector from the NO. 2 antenna cord sub-assembly.
Procedure1
| *a | Front view of wire harness connector
(to Radio Receiver Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DB-5 (DAB-LH [MAIN]) - B-1 | Always | Below 1 Ω |
| DB-5a - B-1a | Always | Below 1 Ω |
| DB-5 (DAB-LH [MAIN]) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Pre-procedure1
Disconnect the antenna connector from the antenna cord sub-assembly.
Disconnect the antenna connector from the digital audio broadcasting antenna assembly LH
Procedure1
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - A-1 | Always | Below 1 Ω |
| B-1a - A-1a | Always | Below 1 Ω |
| B-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Replace the digital audio broadcasting antenna assembly LH with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>DIGITAL AUDIO BROADCASTING ANTENNA>REMOVAL
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B