Home › Power Source / Network › BATTERY / CHARGING › CHARGING SYSTEM
RM37H0E _57 Power Source / Network _097006 BATTERY / CHARGING _0461862 CHARGING SYSTEM C

BATTERY / CHARGING  CHARGING SYSTEM  P058A01  Auxiliary Battery Monitor Module Range/Performance  


DESCRIPTION

The battery state sensor assembly detects the auxiliary voltage, current and temperature of the auxiliary battery. The battery state sensor assembly calculates State of Charge (SOC) based on the voltage and current of the auxiliary battery and sends it to the EV control ECU. Based on the signals received, the EV control ECU adjusts the charging voltage of the DC/DC converter.

The battery state sensor assembly calculates the auxiliary battery temperature based on changes in resistance of a built-in thermistor and sends it to the EV control ECU. The EV control ECU reduces the amount of charging current based on this signal in order to protect the auxiliary battery.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P058A01 Auxiliary Battery Monitor Module Range/Performance Any of the following conditions is met with the ignition switch to ON. (1 trip detection logic):
·

Current is 999.939 A or more, or -1000 A or less for 3.2 seconds or more.

·

The difference between the maximum and minimum current is 0.0305 A or less for 100 seconds or more.

·

A current detection circuit malfunction signal is received.

·

The auxiliary battery temperature is 105°C (221°F) or more or -40°C (-40°F) or less for 12.3 seconds or more.

·

A temperature detection circuit malfunction signal is received.

·

Voltage is 15.98 V or more, or 6.0 V or less for 3.2 seconds or more.

·

A voltage detection circuit malfunction signal is received.

·

A writing error occurs in the auxiliary battery state sensor internal memory (battery identification data).


·

Battery state sensor assembly

·

Auxiliary battery

·

Wire harness or connector


Charge warning light does not come on EV A

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnosis Condition Ignition switch to ON ○ ○ ○ ○ ○
Malfunction Status Current value is 999.939 A or more ○ - - - -
Current value is -1000 A or less - ○ - - -
The difference between the maximum and minimum current is 0.0305 A or less for 100 seconds or more. - - ○ - -
Current detection circuit malfunction condition is received - - - ○ -
Auxiliary battery temperature is 105°C or more - - - - ○
Detection Time 3.2 seconds or more 3.2 seconds or more 100 seconds or more - 12.3 seconds or more
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions
Vehicle Condition
Pattern 6 Pattern 7 Pattern 8 Pattern 9 Pattern 10 Pattern 11
Diagnosis Condition Ignition switch to ON ○ ○ ○ ○ ○ ○
Malfunction Status Auxiliary battery temperature is -40°C or less ○ - - - - -
Temperature detection circuit malfunction signal is received - ○ - - - -
Voltage value remains at 15.98 V or more - - ○ - - -
Voltage value remains at 6.0 V or less - - - ○ - -
Voltage detection circuit malfunction signal is received - - - - ○ -
Writing error occurs in the auxiliary battery state sensor internal memory (battery identification data) - - - - - ○
Detection Time 12.3 seconds or more - 3.2 seconds or more 3.2 seconds or more - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

A458801E15
2.844,0.313 3.052,0.563 0.208,0.25 10 false 3 4.615,0.417 4.823,0.667 0.208,0.25 10 false 2 5.531,0.438 5.781,0.688 0.25,0.25 10 false 13 5.688,2.5 6.063,2.75 0.375,0.25 10 false A17 5.802,0.615 6.26,0.865 0.458,0.25 10 false LIN3 1.458,0.542 2.406,0.792 0.948,0.25 10 false ICS NO. 1 3.031,0.406 3.406,0.656 0.375,0.25 10 false +B 4.333,0.594 4.708,0.844 0.375,0.25 10 false LIN 0.854,2.021 2.104,2.271 1.25,0.25 10 false Auxiliary Battery 1.458,0.948 2.375,1.198 0.917,0.25 10 false ICS NO. 2 3.021,1.135 3.396,1.385 0.375,0.25 10 false J2 5.719,2.698 6.875,2.906 1.156,0.208 10 false EV Control ECU 0.635,3.344 2.458,3.594 1.823,0.25 10 false : LIN Communication Line 3.01,1.313 5.219,1.563 2.208,0.25 10 false Battery State Sensor Assembly 2.833,0.698 3.042,0.948 0.208,0.25 10 false 1 3.042,0.802 3.51,1.031 0.469,0.229 10 false RBAT

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When P162B87 (Lost Communication with Battery Monitor Module Missing Message) is output at the same time, perform troubleshooting for P162B87 (Lost Communication with Battery Monitor Module Missing Message) first.

Click herePower Source / Network>BATTERY / CHARGING>CHARGING SYSTEM>P162B87

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION

OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(J2)Location & Routing

Click Connector(J2)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Battery State Sensor Assembly

J2-3 (+B) - Body ground Ignition switch off 11 to 14 V
J2-1 (RBAT) - Body ground Ignition switch off 11 to 14 V



Post-procedure1

a.

None.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY STATE SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR