Home › Power Source / Network › BATTERY / CHARGING › CHARGING SYSTEM
RM37H0E _57 Power Source / Network _097006 BATTERY / CHARGING _0461862 CHARGING SYSTEM C

BATTERY / CHARGING  CHARGING SYSTEM  P162B87  Lost Communication with Battery Monitor Module Missing Message  


DESCRIPTION

The EV control ECU communicates with the battery state sensor assembly via LIN communication. If a LIN communication error is detected, the EV control ECU stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P162B87 Lost Communication with Battery Monitor Module Missing Message Battery state sensor assembly or EV control ECU communication stops for approximately 17 minutes or more with the ignition switch to ON
(1 trip detection logic)
·

Battery state sensor assembly

·

EV control ECU

·

Wire harness or connector


Charge warning light does not come on EV A

WIRING DIAGRAM

A409155E28
0.906,2.302 1.979,2.51 1.073,0.208 10 false Auxiliary Battery 0.792,3.302 2.448,3.5 1.656,0.198 10 false : LIN Communication Line 1.229,0.792 2.156,1 0.927,0.208 10 false ICS NO. 1 2.271,1.135 2.729,1.333 0.458,0.198 10 false J2 2.25,1.281 4.542,1.479 2.292,0.198 10 false Battery State Sensor Assembly 2.323,0.656 2.635,0.854 0.313,0.198 10 false +B 3.406,0.667 3.719,0.865 0.313,0.198 10 false LIN 2.146,0.552 2.302,0.75 0.156,0.198 10 false 3 3.698,0.51 3.854,0.708 0.156,0.198 10 false 2 5.229,0.5 5.542,0.698 0.313,0.198 10 false 13 5.49,0.667 6.104,0.865 0.615,0.198 10 false LIN3 5.385,2.875 5.844,3.073 0.458,0.198 10 false A17 5.5,3.052 6.74,3.292 1.24,0.24 10 false EV Control ECU 2.271,2.615 2.729,2.813 0.458,0.198 10 false B23 3.719,1.99 4.177,2.188 0.458,0.198 10 false 3 3.26,2.146 3.719,2.344 0.458,0.198 10 false DOUT 2.26,2.771 4.542,3.01 2.281,0.24 10 false Compressor with Motor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the EV control ECU, refer to Service Bulletin.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION
a.

Check installation condition of the battery state sensor assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(J2)Location & Routing

Click Connector(J2)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Battery State Sensor Assembly

J2-3 (+B) - Body ground Ignition switch off 11 to 14 V



Post-procedure1

a.

None.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - BATTERY STATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - BATTERY STATE SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 EV control ECU connector.


b.

Disconnect the J2 battery state sensor assembly connector.


c.

Disconnect the B23 compressor with motor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(A17,J2)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(J2)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Battery State Sensor Assembly

A17-13 (LIN3) - J2-2 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(J2,A17,B23)Location & Routing

Click Connector(J2)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Battery State Sensor Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B23)Engine Compartment>No. 2 Stack Wire>Compressor with Motor Assembly

J2-2 (LIN), A17-13 (LIN3) or B23-3 (DOUT) - Body ground Always 10 kΩ or higher



Post-procedure1

a.

None.


Result:
Proceed to
OK
NG



OK

4.CLEAR DTCS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTCS

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs, and note down any DTCs that are output.

Powertrain > EV > Trouble Codes
50001 397

b.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397

Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTCS (AIR CONDITIONING SYSTEM)
5.CLEAR DTCS (AIR CONDITIONING SYSTEM)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs, and note down any DTCs that are output.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

b.

Clear the DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 121

Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS
6.CHECK FOR DTCS

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and wait for 17 minutes or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397

Post-procedure1

a.

None.


Result:
Result Proceed to
P162B87 is output A
DTCs are not output B



A

7.CHECK FOR DTCS (AIR CONDITIONING SYSTEM)

B

CHECK FOR INTERMITTENT PROBLEMS

7.CHECK FOR DTCS (AIR CONDITIONING SYSTEM)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs when the following conditions are met.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Post-procedure1

a.

None.


Result:
Result Proceed to
B1498 is output A
DTCs are not output B



A

B

REPLACE BATTERY STATE SENSOR ASSEMBLY