Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0455059 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E384958E03
5.906,7.729 7.104,8.104 1.198,0.375 10 false Radio and Display Receiver Assembly 0.146,7.677 1.375,8.083 1.229,0.406 10 false No. 4 Antenna Cord Sub-assembly 4.688,7.719 5.594,8.167 0.906,0.448 10 false Antenna Cord Sub-assembly 1.5,7.667 2.948,8.031 1.448,0.365 10 false No. 2 Amplifier Antenna Assembly 3.083,7.729 4.313,8.135 1.229,0.406 10 false No. 2 Antenna Cord Sub-assembly 0.208,3.292 1.438,3.698 1.229,0.406 10 false No. 3 Antenna Cord Sub-assembly 1.531,5.042 2.792,5.573 1.26,0.531 10 false Back Window Glass (Window Glass Antenna Wire) 1.448,1.51 2.927,1.875 1.479,0.365 10 false No. 1 Amplifier Antenna Assembly 1.375,2.896 1.688,3.094 0.313,0.198 10 false A 5.771,0.698 6.083,0.896 0.313,0.198 10 false RA 5.771,1.135 6.083,1.333 0.313,0.198 10 false RA 5.76,1.573 6.073,1.771 0.313,0.198 10 false RA 5.771,2 6.083,2.198 0.313,0.198 10 false RA 1.375,0.24 1.583,0.427 0.208,0.188 10 false B 1.375,4.719 1.688,4.917 0.313,0.198 10 false E 1.385,7.302 1.698,7.5 0.313,0.198 10 false F 2.854,0.25 3.167,0.448 0.313,0.198 10 false C 2.844,0.698 3.156,0.896 0.313,0.198 10 false C 2.844,1.135 3.156,1.333 0.313,0.198 10 false C 4.333,0.25 4.646,0.448 0.313,0.198 10 false D 4.333,0.688 4.646,0.885 0.313,0.198 10 false D 4.333,1.135 4.646,1.333 0.313,0.198 10 false D 4.333,1.573 4.646,1.771 0.313,0.198 10 false D 4.333,2 4.646,2.198 0.313,0.198 10 false D 5.76,0.24 6.073,0.438 0.313,0.198 10 false RA 2.844,6.396 3.156,6.594 0.313,0.198 10 false G 2.844,6.854 3.156,7.052 0.313,0.198 10 false G 2.854,7.292 3.167,7.49 0.313,0.198 10 false G 5.802,0.073 6.115,0.271 0.313,0.198 10 false 3 5.813,0.531 6.125,0.729 0.313,0.198 10 false 4 5.813,0.958 6.125,1.156 0.313,0.198 10 false 1 5.813,1.396 6.125,1.594 0.313,0.198 10 false 2 5.823,1.813 6.135,2.01 0.313,0.198 10 false 5 6.073,2.031 6.594,2.302 0.521,0.271 10 false ANT+ 6.083,0.24 6.604,0.51 0.521,0.271 10 false MAIN 6.073,1.156 6.594,1.427 0.521,0.271 10 false SUB 4.344,0.083 4.656,0.281 0.313,0.198 10 false 3 4.302,0.51 4.615,0.708 0.313,0.198 10 false 3a 4.344,0.948 4.656,1.146 0.313,0.198 10 false 4 4.313,1.385 4.625,1.583 0.313,0.198 10 false 4a 4.333,1.833 4.656,2.042 0.323,0.208 10 false 1 2.865,0.073 3.177,0.271 0.313,0.198 10 false 2 2.813,0.51 3.125,0.708 0.313,0.198 10 false 2a 2.854,0.948 3.177,1.156 0.323,0.208 10 false 1 2.865,7.104 3.188,7.313 0.323,0.208 10 false 1 2.865,6.219 3.177,6.417 0.313,0.198 10 false 2 2.823,6.677 3.135,6.875 0.313,0.198 10 false 2a 1.385,7.115 1.698,7.313 0.313,0.198 10 false 2 1.375,4.531 1.688,4.729 0.313,0.198 10 false 1 1.385,0.063 1.698,0.26 0.313,0.198 10 false 2 1.375,2.719 1.698,2.927 0.323,0.208 10 false 1

PROCEDURE

1.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are not installed.


NOTICE:

Do not remove optional components without the permission of the customer.



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E245523

Preparation for check

i.

Disconnect the RA radio and display receiver assembly connector.



b.

Check for noise

i.

Turn the ignition switch to ON with the radio and display receiver assembly connector connected.


ii.

Turn the radio and display receiver assembly on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.




Result:
Proceed to
OK
NG



OK

4.CHECK BACK WINDOW GLASS (WINDOW GLASS ANTENNA WIRE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK BACK WINDOW GLASS (WINDOW GLASS ANTENNA WIRE)
a.
E111994C29
0.75,1.115 0.594,0.688 true 1.094,1.896 0.979,1.625 true 2.302,1.656 2.188,1.385 true 0.479,0.51 0.656,0.688 0.177,0.177 10 false *a 1.094,1.906 1.271,2.083 0.177,0.177 10 false *b 2.271,1.677 2.448,1.854 0.177,0.177 10 false *c
*a Tester Probe
*b Antenna Wire
*c Tin Foil


Check for continuity in the window glass antenna wire.

NOTICE:

When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.


HINT:

Check for continuity at the center of each antenna wire as shown in the illustration.


OK:

There is continuity in the window glass antenna wire.



Result:
Proceed to
OK
NG



OK

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR BACK WINDOW GLASS (WINDOW GLASS ANTENNA WIRE)

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E188455E31
1.552,1.104 1.146,1.479 true 0.844,1.51 1.24,1.677 0.396,0.167 10 ANT+

Disconnect the RA radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC, radio switch on and FM or AM selected 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E384959C06
1.479,0.083 1.917,0.365 0.438,0.281 1.448,1.969 1.885,2.25 0.438,0.281 1.063,1.083 1.26,1.083 1.26,1.083 1.521,1.229 true 1.01,0.646 1.208,0.646 1.208,0.646 1.542,0.833 true 1.927,1.115 2.115,0.979 2.115,0.979 2.292,0.979 true 1.677,0.917 2.208,0.531 2.208,0.531 2.385,0.531 true 1.677,1.302 2.188,1.667 2.188,1.667 2.365,1.667 true 2.104,2.958 2.427,2.573 2.427,2.573 2.604,2.573 true 1.771,2.938 2.073,2.292 2.073,2.292 2.25,2.292 true 0.365,0.292 0.677,0.49 0.313,0.198 10 false *a 0.354,2.177 0.667,2.375 0.313,0.198 10 false *b 0.938,1.01 1.354,1.25 0.417,0.24 10 false 4 1.615,2.021 1.927,2.219 0.313,0.198 10 false D 1.594,0.135 1.906,0.333 0.313,0.198 10 false RA 2.438,0.479 2.854,0.719 0.417,0.24 10 false SUB 2.385,0.906 2.802,1.146 0.417,0.24 10 false ANT+ 0.875,0.573 1.292,0.813 0.417,0.24 10 false 2 2.417,1.594 2.833,1.833 0.417,0.24 10 false MAIN 2.667,2.49 3.083,2.729 0.417,0.24 10 false 4a 2.302,2.208 2.719,2.448 0.417,0.24 10 false 3a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the radio and display receiver assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - D-3 Always Below 1 Ω
RA-4 - D-3a Always Below 1 Ω
RA-1 (SUB) - D-4 Always Below 1 Ω
RA-2 - D-4a Always Below 1 Ω
RA-5 (ANT+) - D-1 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-1 (SUB) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E384960C02
1.49,0.167 1.906,0.427 0.417,0.26 1.479,1.781 1.896,2.042 0.417,0.26 1.469,3.25 1.885,3.51 0.417,0.26 1.094,1.583 1.25,1.583 1.25,1.583 1.469,1.229 true 1.844,1.219 2.094,1.552 2.094,1.552 2.229,1.552 true 1.896,2.677 2.146,3.01 2.146,3.01 2.281,3.01 true 1.906,4.146 2.156,4.479 2.156,4.479 2.292,4.479 true 1.656,0.208 1.917,0.521 0.26,0.313 10 false D 1.635,1.833 1.896,2.146 0.26,0.313 10 false C 0.24,0.26 0.5,0.573 0.26,0.313 10 false *a 0.302,2 0.563,2.313 0.26,0.313 10 false *b 0.906,1.479 1.167,1.792 0.26,0.313 10 false 4a 2.365,2.927 2.625,3.24 0.26,0.313 10 false 2a 2.302,1.458 2.563,1.771 0.26,0.313 10 false 3a 1.635,3.313 1.896,3.625 0.26,0.313 10 false G 2.344,4.406 2.604,4.615 0.26,0.208 10 false 2a 0.354,3.438 0.615,3.75 0.26,0.313 10 false *c
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*c Front view of wire harness connector
(to No. 2 Amplifier Antenna Assembly)


Disconnect the antenna connector from the antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


c.

Disconnect the antenna connector from the No. 2 amplifier antenna assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-1 - C-1 Always Below 1 Ω
D-1 - G-1 Always Below 1 Ω
D-4 - G-2 Always Below 1 Ω
D-4a - G-2a Always Below 1 Ω
D-3 - C-2 Always Below 1 Ω
D-3a - C-2a Always Below 1 Ω
D-1 - Body ground Always 10 kΩ or higher
D-4 - Body ground Always 10 kΩ or higher
D-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

8.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E384956C03
1.552,0.292 1.896,0.552 0.344,0.26 1.531,2.594 1.875,2.854 0.344,0.26 1.677,0.323 1.833,0.521 0.156,0.198 10 false B 1.667,2.635 1.823,2.833 0.156,0.198 10 false A 0.313,0.385 0.573,0.708 0.26,0.323 10 false *a 0.406,2.625 0.667,2.948 0.26,0.323 10 false *b
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to Back Window Glass [Window Glass Antenna Wire])


Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


b.

Disconnect the antenna connector from the back window glass (window glass antenna wire).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - A-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

9.CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E384957C02
1.51,0.219 1.844,0.521 0.333,0.302 1.51,2.479 1.844,2.781 0.333,0.302 0.26,0.167 0.573,0.365 0.313,0.198 10 false *a 0.292,2.833 0.604,3.031 0.313,0.198 10 false *b 1.625,2.552 1.938,2.75 0.313,0.198 10 false E 1.646,0.292 1.958,0.49 0.313,0.198 10 false F
*a Front view of wire harness connector
(to No. 2 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to Back Window Glass [Window Glass Antenna Wire])


Disconnect the antenna connector from the No. 2 amplifier antenna assembly.


b.

Disconnect the antenna connector from the back window glass (window glass antenna wire).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F-2 - E-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY

10.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

11.CHECK NO. 2 AMPLIFIER ANTENNA ASSEMBLY
11.CHECK NO. 2 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No.2 amplifier antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (NO. 2 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY