Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455115 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  Image from Camera for Panoramic View Monitor is Abnormal  


DESCRIPTION

The display signal from each television camera is transmitted to the multi-display assembly via the parking assist ECU.

WIRING DIAGRAM

E431824E06
1.365,7.208 1.844,7.406 0.479,0.198 10 false CGND 1.375,7.688 1.875,7.885 0.5,0.198 10 false SGND 1.375,4.698 1.99,4.896 0.615,0.198 10 false SGND 0.635,5.125 2.906,5.406 2.271,0.281 10 false Front Television Camera Assembly 5.417,8.188 6.656,8.396 1.24,0.208 10 false Parking Assist ECU 2.01,0.115 2.313,0.344 0.302,0.229 10 false 1 2.021,0.615 2.25,0.813 0.229,0.198 10 false 2 2.01,1.135 2.167,1.333 0.156,0.198 10 false 3 0.635,7.969 0.927,8.146 0.292,0.177 10 false K12 1.51,6.708 1.813,6.896 0.302,0.188 10 false CV- 1.49,6.229 1.844,6.406 0.354,0.177 10 false CV+ 1.469,5.719 1.833,5.917 0.365,0.198 10 false CB+ 5.531,5.729 5.865,5.917 0.333,0.188 10 false CB+ 5.521,6.24 5.854,6.438 0.333,0.198 10 false CV+ 5.521,6.74 5.833,6.958 0.313,0.219 10 false CV- 5.531,7.219 6,7.406 0.469,0.188 10 false CGND 1.896,3.125 2.271,3.302 0.375,0.177 10 false 4 1.896,2.635 2.271,2.813 0.375,0.177 10 false 2 1.896,3.646 2.271,3.823 0.375,0.177 10 false 3 0.635,4.979 0.927,5.167 0.292,0.188 10 false A95 1.344,4.219 1.958,4.417 0.615,0.198 10 false BGND 1.375,3.708 1.99,3.906 0.615,0.198 10 false BCV- 1.365,3.219 1.979,3.417 0.615,0.198 10 false BCV+ 1.365,2.729 1.979,2.927 0.615,0.198 10 false BCB+ 1.896,4.625 2.219,4.802 0.323,0.177 10 false 5 1.896,4.146 2.219,4.323 0.323,0.177 10 false 1 5.177,2.51 5.563,2.677 0.385,0.167 10 false 2 5.188,3 5.521,3.177 0.333,0.177 10 false 4 3.385,7.76 3.542,7.958 0.156,0.198 10 false * 5.177,0.115 5.563,0.333 0.385,0.219 10 false 1 5.198,0.604 5.406,0.771 0.208,0.167 10 false 2 5.188,1.104 5.365,1.302 0.177,0.198 10 false 3 5.521,1.854 6.01,2.052 0.49,0.198 10 false RSW+ 5.063,0.344 5.479,0.531 0.417,0.188 10 false G138 1.385,0.333 1.833,0.521 0.448,0.188 10 false GVO+ 1.385,0.802 1.781,0.979 0.396,0.177 10 false GVO- 1.375,1.313 1.813,1.51 0.438,0.198 10 false GVG1 1.906,6.156 2.073,6.344 0.167,0.188 10 false 6 1.896,5.667 2.052,5.833 0.156,0.167 10 false 4 1.917,7.135 2.094,7.313 0.177,0.177 10 false 3 1.906,7.615 2.083,7.823 0.177,0.208 10 false 7 1.917,6.656 2.042,6.823 0.125,0.167 10 false 5 0.635,8.115 2.781,8.333 2.146,0.219 10 false Rear Television Camera Assembly 5.521,0.333 5.99,0.531 0.469,0.198 10 false GVO+ 5.521,0.823 5.958,1.01 0.438,0.188 10 false GVO- 5.531,1.323 5.979,1.51 0.448,0.188 10 false GVG1 5.073,0.823 5.49,1.01 0.417,0.188 10 false G138 5.073,1.333 5.49,1.521 0.417,0.188 10 false G138 5.063,2.719 5.479,2.906 0.417,0.188 10 false G140 5.531,2.719 5.969,2.917 0.438,0.198 10 false BCB+ 5.521,3.208 5.958,3.406 0.438,0.198 10 false BCV+ 5.531,3.719 5.938,3.917 0.406,0.198 10 false BCV- 5.531,4.219 6.021,4.417 0.49,0.198 10 false BGND 5.177,3.51 5.51,3.688 0.333,0.177 10 false 3 5.188,4.01 5.521,4.188 0.333,0.177 10 false 1 5.188,4.5 5.521,4.677 0.333,0.177 10 false 5 5.073,3.208 5.49,3.396 0.417,0.188 10 false G140 5.073,3.719 5.49,3.906 0.417,0.188 10 false G140 5.073,4.229 5.49,4.417 0.417,0.188 10 false G140 5.073,4.708 5.49,4.896 0.417,0.188 10 false G140 3.375,4.781 3.531,4.979 0.156,0.198 10 false * 3.385,1.313 3.542,1.51 0.156,0.198 10 false * 5.073,5.729 5.49,5.917 0.417,0.188 10 false G142 5.063,6.24 5.479,6.427 0.417,0.188 10 false G142 5.063,6.74 5.479,6.927 0.417,0.188 10 false G142 5.063,7.229 5.479,7.417 0.417,0.188 10 false G142 5.073,7.698 5.49,7.885 0.417,0.188 10 false G142 5.177,5.51 5.604,5.688 0.427,0.177 10 false 2 5.198,6.031 5.573,6.208 0.375,0.177 10 false 4 5.198,6.521 5.573,6.698 0.375,0.177 10 false 3 5.188,7.01 5.51,7.188 0.323,0.177 10 false 1 5.198,7.5 5.521,7.677 0.323,0.177 10 false 5 5.521,7.698 5.979,7.885 0.458,0.188 10 false SGND 0.76,8.479 1.615,8.667 0.854,0.188 10 false : GVIF Cable 2.26,8.5 3.177,8.688 0.917,0.188 10 false *: Shielded 5.521,4.708 5.99,4.906 0.469,0.198 10 false SGND 0.521,2.146 2.792,2.427 2.271,0.281 10 false Multi-display Assembly 1.354,1.833 1.823,2.021 0.469,0.188 10 false CSW+ 5.094,1.844 5.406,2.021 0.313,0.177 10 false G13 5.156,1.615 5.396,1.781 0.24,0.167 10 false 13 2.01,1.635 2.313,1.865 0.302,0.229 10 false 1 1.917,1.844 2.229,2.01 0.313,0.167 10 false D60 1.885,0.344 2.25,0.521 0.365,0.177 10 false D154 1.885,0.813 2.25,0.99 0.365,0.177 10 false D154 1.885,1.323 2.25,1.5 0.365,0.177 10 false D154

E461425E01
5.073,0.604 5.417,0.781 0.344,0.177 10 false G141 5.063,1.104 5.417,1.292 0.354,0.188 10 false G141 5.063,1.615 5.458,1.802 0.396,0.188 10 false G141 5.063,2.125 5.469,2.323 0.406,0.198 10 false G141 5.063,2.625 5.448,2.833 0.385,0.208 10 false G141 5.063,4.917 5.448,5.115 0.385,0.198 10 false G139 5.073,5.417 5.438,5.604 0.365,0.188 10 false G139 5.073,5.927 5.479,6.135 0.406,0.208 10 false G139 5.073,6.438 5.458,6.635 0.385,0.198 10 false G139 5.063,6.938 5.427,7.104 0.365,0.167 10 false G139 5.198,0.396 5.354,0.573 0.156,0.177 10 false 2 5.188,0.896 5.354,1.083 0.167,0.188 10 false 4 5.188,1.396 5.333,1.583 0.146,0.188 10 false 3 5.188,1.885 5.448,2.073 0.26,0.188 10 false 1 5.198,2.417 5.458,2.604 0.26,0.188 10 false 5 3.76,0.49 4.021,0.677 0.26,0.188 10 false 2 3.75,1.01 4.01,1.198 0.26,0.188 10 false 4 3.76,1.51 4.021,1.698 0.26,0.188 10 false 3 3.771,2.021 4.031,2.208 0.26,0.188 10 false 1 3.771,2.51 4.031,2.698 0.26,0.188 10 false 5 1.906,1.521 2.167,1.708 0.26,0.188 10 false 2 1.896,2.031 2.156,2.219 0.26,0.188 10 false 1 1.917,0.49 2.177,0.677 0.26,0.188 10 false 3 1.906,1.021 2.167,1.208 0.26,0.188 10 false 4 1.917,2.521 2.177,2.708 0.26,0.188 10 false 5 1.396,0.573 1.823,0.792 0.427,0.219 10 false LCB+ 1.427,1.583 1.813,1.781 0.385,0.198 10 false LCV- 1.396,1.104 1.823,1.313 0.427,0.208 10 false LCV+ 1.375,2.104 1.844,2.313 0.469,0.208 10 false LGND 1.375,2.625 1.854,2.823 0.479,0.198 10 false SGND 5.521,0.594 5.917,0.771 0.396,0.177 10 false LCB+ 5.531,1.094 5.938,1.313 0.406,0.219 10 false LCV+ 5.542,1.594 5.948,1.792 0.406,0.198 10 false LCV- 5.542,2.104 5.99,2.313 0.448,0.208 10 false LGND 5.542,2.615 6.01,2.802 0.469,0.188 10 false SGND 3.24,0.5 3.646,0.698 0.406,0.198 10 false LCB+ 3.25,1.01 3.667,1.219 0.417,0.208 10 false LCV+ 3.26,1.51 3.656,1.719 0.396,0.208 10 false LCV- 3.177,2.01 3.635,2.198 0.458,0.188 10 false LGND 3.188,2.531 3.635,2.74 0.448,0.208 10 false SGND 0.313,2.781 0.49,2.979 0.177,0.198 10 false A 0.302,2.979 1.76,3.313 1.458,0.333 10 false Side Television Camera Assembly LH 0.677,8.052 1.01,8.229 0.333,0.177 10 false E18 1.042,3.719 3.365,3.948 2.323,0.229 10 false Outer Rear View Mirror Assembly LH 1.135,8.052 3.469,8.24 2.333,0.188 10 false Outer Rear View Mirror Assembly RH 0.323,7.115 0.531,7.302 0.208,0.188 10 false B 0.313,7.281 1.771,7.677 1.458,0.396 10 false Side Television Camera Assembly RH 0.531,3.729 0.865,3.906 0.333,0.177 10 false E35 3.771,6.833 3.938,7.021 0.167,0.188 10 false 5 3.76,6.333 3.948,6.5 0.188,0.167 10 false 1 3.771,5.833 3.958,6 0.188,0.167 10 false 3 3.771,5.333 3.938,5.521 0.167,0.188 10 false 4 3.76,4.823 3.927,5.01 0.167,0.188 10 false 2 5.198,4.667 5.385,4.854 0.188,0.188 10 false 2 5.188,5.188 5.354,5.375 0.167,0.188 10 false 4 5.177,5.698 5.333,5.885 0.156,0.188 10 false 3 5.177,6.198 5.333,6.406 0.156,0.208 10 false 1 5.208,6.74 5.385,6.927 0.177,0.188 10 false 5 1.906,5.844 2.167,6.031 0.26,0.188 10 false 2 1.906,6.333 2.073,6.51 0.167,0.177 10 false 1 1.906,4.802 2.083,4.99 0.177,0.188 10 false 3 1.917,5.323 2.177,5.51 0.26,0.188 10 false 4 1.906,6.865 2.073,7.052 0.167,0.188 10 false 5 1.375,4.875 1.813,5.063 0.438,0.188 10 false RCB+ 1.406,5.406 1.854,5.615 0.448,0.208 10 false RCV+ 1.438,5.906 1.844,6.125 0.406,0.219 10 false RCV- 1.375,6.438 1.823,6.635 0.448,0.198 10 false RGND 1.385,6.938 1.823,7.146 0.438,0.208 10 false SGND 3.219,4.823 3.646,5.01 0.427,0.188 10 false RCB+ 3.219,5.323 3.646,5.51 0.427,0.188 10 false RCV+ 3.271,5.833 3.688,6.042 0.417,0.208 10 false RCV- 3.208,6.344 3.677,6.552 0.469,0.208 10 false RGND 3.177,6.844 3.625,7.042 0.448,0.198 10 false SGND 5.521,4.885 5.958,5.083 0.438,0.198 10 false RCB+ 5.521,5.406 5.958,5.594 0.438,0.188 10 false RCV+ 5.542,5.917 5.927,6.104 0.385,0.188 10 false RCV- 5.542,6.438 6.031,6.615 0.49,0.177 10 false RGND 5.521,6.938 5.958,7.125 0.438,0.188 10 false SGND 0.219,8.438 2.688,8.677 2.469,0.24 10 false *: Shielded 5.427,7.531 6.729,7.74 1.302,0.208 10 false Parking Assist ECU 4.313,2.615 4.448,2.771 0.135,0.156 10 false * 4.313,6.917 4.479,7.094 0.167,0.177 10 false * 1.969,2.99 3.583,3.167 1.615,0.177 10 false Outer Mirror Retractor LH 1.969,7.292 3.594,7.49 1.625,0.198 10 false Outer Mirror Retractor RH

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the auxiliary battery terminal has been disconnected, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



HINT:
Images may be unclear even in normal conditions if:
·

Electrical devices are used in the cabin (noise may occur in the image).

·

The camera lens is frosted over (the image immediately after turning the ignition switch to ON may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night, etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The television camera assembly lens is scratched.

·

The television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK PANORAMIC VIEW MONITOR SYSTEM
a.

Check if the same malfunction occurs when the panoramic view monitor screen is displayed.


Result:
Result Proceed to
Rear view screen is not displayed. A
Front view screen is not displayed. B
Side monitor screen (LH side) is not displayed. C
Side monitor screen (RH side) is not displayed. D
Panoramic view monitor screen is not displayed. E



A

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)

D

13.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)

E

18.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - MULTI- DISPLAY ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G142 parking assist ECU connector.


b.

Disconnect the K12 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G142,K12)Location & Routing

Click Connector(G142)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

G142-2 (CB+) - K12-4 (CB+) Always Below 1 Ω
G142-4 (CV+) - K12-6 (CV+) Always Below 1 Ω
G142-3 (CV-) - K12-5 (CV-) Always Below 1 Ω
G142-1 (CGND) - K12-3 (CGND) Always Below 1 Ω
G142-5 (SGND) - K12-7 (SGND) Always Below 1 Ω
G142-2 (CB+) or K12-4 (CB+) - Body ground Always 10 kΩ or higher
G142-4 (CV+) or K12-6 (CV+) - Body ground Always 10 kΩ or higher
G142-3 (CV-) or K12-5 (CV-) - Body ground Always 10 kΩ or higher
G142-1 (CGND) or K12-3 (CGND) - Body ground Always 10 kΩ or higher
G142-5 (SGND) - K12-7 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (CV-, CGND)
a.
E394295C01
1.979,0.854 2.333,0.479 2.333,0.479 2.583,0.479 true 2,1.104 2.354,1.563 2.354,1.563 2.604,1.563 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.646,0.417 3.167,0.615 0.521,0.198 10 false CGND 2.667,1.49 3.188,1.688 0.521,0.198 10 false CV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the G142 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (CGND) - Body ground Always Below 1 Ω
3 (CV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

4.CHECK PARKING ASSIST ECU (CB+, CGND)
a.

Disconnect the rear television camera assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K12)Location & Routing

Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

K12-3 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(K12)Location & Routing

Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

K12-4 (CB+) - K12-3 (CGND) Ignition switch ON 7 to 8 V
K12-4 (CB+) - K12-3 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G140 parking assist ECU connector.


b.

Disconnect the A95 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G140,A95)Location & Routing

Click Connector(G140)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

Click Connector(A95)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Television Camera Assembly

G140-2 (BCB+) - A95-2 (BCB+) Always Below 1 Ω
G140-4 (BCV+) - A95-4 (BCV+) Always Below 1 Ω
G140-3 (BCV-) - A95-3 (BCV-) Always Below 1 Ω
G140-1 (BGND) - A95-1 (BGND) Always Below 1 Ω
G140-5 (SGND) - A95-5 (SGND) Always Below 1 Ω
G140-2 (BCB+) or A95-2 (BCB+) - Body ground Always 10 kΩ or higher
G140-4 (BCV+) or A95-4 (BCV+) - Body ground Always 10 kΩ or higher
G140-3 (BCV-) or A95-3 (BCV-) - Body ground Always 10 kΩ or higher
G140-1 (BGND) or A95-1 (BGND) - Body ground Always 10 kΩ or higher
G140-5 (SGND) or A95-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK PARKING ASSIST ECU (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK PARKING ASSIST ECU (BCV-, BGND)
a.
E394296C01
1.969,0.854 2.313,0.417 2.313,0.417 2.563,0.417 true 1.979,1.083 2.313,1.552 2.313,1.552 2.563,1.552 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 2.615,0.344 3.229,0.542 0.615,0.198 10 false BGND 2.625,1.479 3.24,1.677 0.615,0.198 10 false BCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the G140 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BGND) - Body ground Always Below 1 Ω
3 (BCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

7.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.

Disconnect the front television camera assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A95)Location & Routing

Click Connector(A95)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Television Camera Assembly

A95-1 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A95)Location & Routing

Click Connector(A95)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Television Camera Assembly

A95-2 (BCB+) - A95-1 (BGND) Ignition switch ON 7 to 8 V
A95-2 (BCB+) - A95-1 (BGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the G141 parking assist ECU connector.


b.

Disconnect the E35 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G141,E35)Location & Routing

Click Connector(G141)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

Click Connector(E35)Body>Front Door Wire LH / Front Door Wire RH>Side Television Camera Assembly LH

G141-2 (LCB+) - E35-2 (LCB+) Always Below 1 Ω
G141-4 (LCV+) - E35-4 (LCV+) Always Below 1 Ω
G141-3 (LCV-) - E35-3 (LCV-) Always Below 1 Ω
G141-1 (LGND) - E35-1 (LGND) Always Below 1 Ω
G141-5 (SGND) - E35-5 (SGND) Always Below 1 Ω
G141-2 (LCB+) or E35-2 (LCB+) - Body ground Always 10 kΩ or higher
G141-4 (LCV+) or E35-4 (LCV+) - Body ground Always 10 kΩ or higher
G141-3 (LCV-) or E35-3 (LCV-) - Body ground Always 10 kΩ or higher
G141-1 (LGND) or E35-1 (LGND) - Body ground Always 10 kΩ or higher
G141-5 (SGND) or E35-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK PARKING ASSIST ECU (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK PARKING ASSIST ECU (LCV-, LGND)
a.
E394297C01
1.969,0.885 2.333,0.5 2.333,0.5 2.583,0.5 true 1.969,1.115 2.333,1.5 2.333,1.5 2.583,1.5 true 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 2.656,0.427 3.271,0.625 0.615,0.198 10 false LGND 2.646,1.438 3.26,1.635 0.615,0.198 10 false LCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the G141 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (LGND) - Body ground Always Below 1 Ω
3 (LCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK PARKING ASSIST ECU (LCB+, LGND)

NG

10.CHECK PARKING ASSIST ECU (LCB+, LGND)
a.

Disconnect the outer rear view mirror assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E35)Location & Routing

Click Connector(E35)Body>Front Door Wire LH / Front Door Wire RH>Side Television Camera Assembly LH

E35-1 (LGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(E35)Location & Routing

Click Connector(E35)Body>Front Door Wire LH / Front Door Wire RH>Side Television Camera Assembly LH

E35-2 (LCB+) - E35-1 (LGND) Ignition switch ON 7 to 8 V
E35-2 (LCB+) - E35-1 (LGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

11.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

11.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E461445C01
1.479,0.167 1.979,0.417 0.5,0.25 0.875,3.781 1.563,3.458 true 2.385,4.063 1.729,3.698 true 2.438,3.635 1.844,3.427 true 2.406,2.854 1.823,3.229 true 0.844,2.813 1.542,3.208 true 2.5,2 2.417,2 2.417,2 2.302,1.5 true 2.594,1.615 2.344,1.354 true 2.667,0.771 2.333,1.115 true 1.833,0.74 2.167,1.104 true 1.76,1.792 2.167,1.313 true 0.094,0.177 0.406,0.375 0.313,0.198 10 false *a 0.146,2.01 0.458,2.208 0.313,0.198 10 false *b 1.427,1.802 2.042,2 0.615,0.198 10 false LCB+ 2.74,0.656 3.354,0.854 0.615,0.198 10 false LCV- 2.74,1.604 3.354,1.802 0.615,0.198 10 false LCV+ 1.385,0.583 2,0.781 0.615,0.198 10 false LGND 2.552,1.885 3.167,2.083 0.615,0.198 10 false SGND 0.458,3.719 1.073,3.917 0.615,0.198 10 false LCV- 0.448,2.688 1.063,2.885 0.615,0.198 10 false LGND 2.521,2.74 3.135,2.938 0.615,0.198 10 false LCB+ 2.542,3.594 3.156,3.792 0.615,0.198 10 false LCV+ 2.448,4.021 3.063,4.219 0.615,0.198 10 false SGND 1.708,0.198 1.958,0.396 0.25,0.198 10 false A
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (LCB+) - A-3 (LCB+) Always Below 1 Ω
4 (LCV+) - A-4 (LCV+) Always Below 1 Ω
3 (LCV-) - A-2 (LCV-) Always Below 1 Ω
1 (LGND) - A-1 (LGND) Always Below 1 Ω
5 (SGND) - A-5 (SGND) Always Below 1 Ω
2 (LCB+) or A-3 (LCB+) - Body ground Always 10 kΩ or higher
4 (LCV+) or A-4 (LCV+) - Body ground Always 10 kΩ or higher
3 (LCV-) or A-2 (LCV-) - Body ground Always 10 kΩ or higher
1 (LGND) or A-1 (LGND) - Body ground Always 10 kΩ or higher
5 (SGND) or A-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH WAS DEFECTIVE)

NG

13.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the G139 parking assist ECU connector.


b.

Disconnect the E18 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G139,E18)Location & Routing

Click Connector(G139)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

Click Connector(E18)Body>Front Door Wire LH / Front Door Wire RH>Side Television Camera Assembly RH

G139-2 (RCB+) - E18-2 (RCB+) Always Below 1 Ω
G139-4 (RCV+) - E18-4 (RCV+) Always Below 1 Ω
G139-3 (RCV-) - E18-3 (RCV-) Always Below 1 Ω
G139-1 (RGND) - E18-1 (RGND) Always Below 1 Ω
G139-5 (SGND) - E18-5 (SGND) Always Below 1 Ω
G139-2 (RCB+) or E18-2 (RCB+) - Body ground Always 10 kΩ or higher
G139-4 (RCV+) or E18-4 (RCV+) - Body ground Always 10 kΩ or higher
G139-3 (RCV-) or E18-3 (RCV-) - Body ground Always 10 kΩ or higher
G139-1 (RGND) or E18-1 (RGND) - Body ground Always 10 kΩ or higher
G139-5 (SGND) or E18-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK PARKING ASSIST ECU (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK PARKING ASSIST ECU (RCV-, RGND)
a.
E394298C01
1.969,0.865 2.333,0.51 2.333,0.51 2.583,0.51 true 1.979,1.083 2.333,1.333 2.333,1.333 2.583,1.333 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 2.635,0.448 3.083,0.646 0.448,0.198 10 false RGND 2.635,1.26 3.083,1.458 0.448,0.198 10 false RCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the G139 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (RGND) - Body ground Always Below 1 Ω
3 (RCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

15.CHECK PARKING ASSIST ECU (RCB+, RGND)
a.

Disconnect the outer rear view mirror assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E18)Location & Routing

Click Connector(E18)Body>Front Door Wire LH / Front Door Wire RH>Side Television Camera Assembly RH

E18-1 (RGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(E18)Location & Routing

Click Connector(E18)Body>Front Door Wire LH / Front Door Wire RH>Side Television Camera Assembly RH

E18-2 (RCB+) - E18-1 (RGND) Ignition switch ON 7 to 8 V
E18-2 (RCB+) - E18-1 (RGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

16.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

16.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E461445C03
1.458,0.115 1.958,0.365 0.5,0.25 0.875,3.781 1.563,3.458 true 2.385,4.063 1.729,3.698 true 2.438,3.635 1.844,3.427 true 2.406,2.854 1.823,3.229 true 0.844,2.813 1.542,3.208 true 2.385,1.948 2.302,1.948 2.302,1.948 2.229,1.51 true 2.646,1.625 2.375,1.323 true 2.615,0.76 2.385,1.125 true 1.958,0.729 2.167,1.125 true 1.854,1.76 2.167,1.344 true 0.094,0.177 0.406,0.375 0.313,0.198 10 false *a 0.146,2.01 0.458,2.208 0.313,0.198 10 false *b 1.521,1.802 2.135,2 0.615,0.198 10 false RCB+ 2.656,0.604 3.271,0.802 0.615,0.198 10 false RCV- 2.708,1.615 3.323,1.813 0.615,0.198 10 false RCV+ 1.604,0.542 2.219,0.74 0.615,0.198 10 false RGND 2.469,1.844 3.083,2.042 0.615,0.198 10 false SGND 0.458,3.719 1.073,3.917 0.615,0.198 10 false RCV- 0.438,2.688 1.052,2.885 0.615,0.198 10 false RGND 2.5,2.74 3.115,2.938 0.615,0.198 10 false RCB+ 2.542,3.594 3.156,3.792 0.615,0.198 10 false RCV+ 2.448,4.021 3.063,4.219 0.615,0.198 10 false SGND 1.656,0.146 1.906,0.344 0.25,0.198 10 false B
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)
*b Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RCB+) - B-3 (RCB+) Always Below 1 Ω
4 (RCV+) - B-4 (RCV+) Always Below 1 Ω
3 (RCV-) - B-2 (RCV-) Always Below 1 Ω
1 (RGND) - B-1 (RGND) Always Below 1 Ω
5 (SGND) or B-5 (SGND) Always 10 kΩ or higher
2 (RCB+) or B-3 (RCB+) - Body ground Always 10 kΩ or higher
4 (RCV+) or B-4 (RCV+) - Body ground Always 10 kΩ or higher
3 (RCV-) or B-2 (RCV-) - Body ground Always 10 kΩ or higher
1 (RGND) or B-1 (RGND) - Body ground Always 10 kΩ or higher
5 (SGND) or B-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

17.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH WAS DEFECTIVE)

NG

18.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - MULTI- DISPLAY ASSEMBLY)
a.

Disconnect the G13 parking assist ECU connector.


b.

Disconnect the D60 multi-display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G13,D60)Location & Routing

Click Connector(G13)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

Click Connector(D60)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

G13-13 (RSW+) - D60-1 (CSW+) Always Below 1 Ω
G13-13 (RSW+) or D60-1 (CSW+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (GVIF CABLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
a.

Replace the GVIF cable with a new or normally functioning one.


b.

Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (GVIF CABLE WAS DEFECTIVE)

NG

20.CHECK MULTI-DISPLAY
20.CHECK MULTI-DISPLAY
a.

Replace the multi-display assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY>REMOVAL


b.

Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (MULTI-DISPLAY ASSEMBLY WAS DEFECTIVE)

NG