Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P056014  System Voltage (BATT) Circuit Short to Ground or Open  


DESCRIPTION

Auxiliary battery power is supplied to the BATT terminal of the EV control ECU in order to store DTCs and freeze frame data. Even if the ignition switch is turned off, back-up power is supplied.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P056014 System Voltage (BATT) Circuit Short to Ground or Open Malfunction in the EV control ECU back-up power source circuit
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

Fuse


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
A478525E01
1,2.219 2.188,2.5 1.188,0.281 10 false Auxiliary Battery 1.76,1.302 2.594,1.469 0.833,0.167 10 false R/B RR#1 3.646,1.323 4.656,1.49 1.01,0.167 10 false ECU-B P 5.677,1.146 6.094,1.333 0.417,0.188 10 false BATT 5.677,2.208 6.01,2.385 0.333,0.177 10 false E1 5.49,2.854 6.656,3.052 1.167,0.198 10 false EV Control ECU 5.302,2.208 5.635,2.385 0.333,0.177 10 false A17 5.323,1.135 5.656,1.313 0.333,0.177 10 false A8 5.385,0.917 5.542,1.115 0.156,0.198 10 false 1 5.396,1.99 5.552,2.188 0.156,0.198 10 false 4 3.979,1 4.135,1.198 0.156,0.198 10 false 2 3.729,1 3.885,1.198 0.156,0.198 10 false 1

for RHD:
A478525E02
1,2.219 2.188,2.5 1.188,0.281 10 false Auxiliary Battery 1.76,1.302 2.594,1.469 0.833,0.167 10 false R/B RR#1 3.646,1.323 4.656,1.49 1.01,0.167 10 false ECU-B P 5.677,1.146 6.094,1.333 0.417,0.188 10 false BATT 5.677,2.208 6.01,2.385 0.333,0.177 10 false E1 5.49,2.854 6.656,3.052 1.167,0.198 10 false EV Control ECU 5.302,2.208 5.635,2.385 0.333,0.177 10 false A17 5.281,1.125 5.615,1.302 0.333,0.177 10 false D15 5.385,0.917 5.542,1.115 0.156,0.198 10 false 1 5.396,1.99 5.552,2.188 0.156,0.198 10 false 4 3.979,1 4.135,1.198 0.156,0.198 10 false 2 3.729,1 3.885,1.198 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)
a.

Check the connector connections and contact pressure of the relevant terminals for the EV control ECU connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


A479018C03
0.344,0.094 0.656,0.292 0.313,0.198 10 false *A 3.813,0.094 4.125,0.292 0.313,0.198 10 false *B
*A for LHD *B for RHD


OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - ECU-B P FUSE)

NG

CONNECT SECURELY

2.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - ECU-B P FUSE)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.
A478491C45
1.979,0.802 2.375,1.156 0.396,0.354 2.604,0.813 3.021,1.156 0.417,0.344 2.625,0.344 3.031,0.708 0.406,0.365 2.219,1.677 1.948,2.479 true 3.042,1.667 2.917,2.469 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.719,0.448 3.021,0.615 0.302,0.167 10 false A8 2.073,0.917 2.375,1.083 0.302,0.167 10 false A17 1.833,2.51 2.135,2.677 0.302,0.167 10 false E1 2.781,2.51 3.167,2.677 0.385,0.167 10 false BATT 2.688,0.906 3.146,1.104 0.458,0.198 10 false D15 3.094,0.417 3.406,0.615 0.313,0.198 10 false *A 3.073,0.969 3.385,1.167 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A8,A17)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-1 (BATT) - A17-4 (E1) Ignition switch off 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(D15,A17)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

D15-1 (BATT) - A17-4 (E1) Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

3.CHECK FUSE (ECU-B P FUSE)
3.CHECK FUSE (ECU-B P FUSE)

Pre-procedure1

a.
A478522C01
0.99,2.76 1.375,2.146 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *1 0.823,2.781 1.104,2.969 0.281,0.188 10 false *2
*1 Luggage Room Relay Block
*2 ECU-B P Fuse


Remove the ECU-B P fuse from the luggage room relay block.


Procedure1

a.

Check if there is an open circuit in the ECU-B P fuse in the luggage room relay block.

OK:

There is no open circuit in the ECU-B P fuse.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the ECU-B P fuse.



OK

4.CHECK HARNESS AND CONNECTOR (ECU-B P FUSE - BATTERY TERMINAL)

NG

REPLACE FUSE (ECU-B P)

4.CHECK HARNESS AND CONNECTOR (ECU-B P FUSE - BATTERY TERMINAL)

Pre-procedure1

a.

Remove the ECU-B P fuse from the luggage room relay block.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the cable from the positive (+) auxiliary battery terminal.


Procedure1

a.
A478523C01
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 1.75,2.615 2.063,2.813 0.313,0.198 10 false *2
*1 Luggage Room Relay Block
*2 ECU-B P Fuse


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ECU-B P fuse holder) - Auxiliary battery positive (+) cable Ignition switch off Below 1 Ω
1 (ECU-B P fuse holder) - Body ground Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the cable to the positive (+) auxiliary battery terminal.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Install the ECU-B P fuse.



OK

5.CHECK HARNESS AND CONNECTOR (ECU-B P FUSE - EV CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECU-B P FUSE - EV CONTROL ECU)

Pre-procedure1

a.

Remove the ECU-B P fuse from the luggage room relay block.


b.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A478524C03
6.198,0.448 6.604,0.781 0.406,0.333 6.198,0.052 6.604,0.385 0.406,0.333 6.313,2.375 6.615,1.865 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *1 1.875,2.125 2.188,2.323 0.313,0.198 10 false *2 3.74,0.135 4.052,0.333 0.313,0.198 10 false *a 6.146,2.406 6.594,2.583 0.448,0.177 10 false BATT 6.323,0.135 6.625,0.302 0.302,0.167 10 false A8 6.292,0.531 6.75,0.729 0.458,0.198 10 false D15 6.698,0.125 7.01,0.323 0.313,0.198 10 false *A 6.698,0.5 7.01,0.698 0.313,0.198 10 false *B
*A for LHD *B for RHD
*1 Luggage Room Relay Block *2 ECU-B P Fuse
*a Rear view of wire harness connector
(to EV Control ECU)
- -


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

2 (ECU-B P fuse holder) - A8-1 (BATT) Ignition switch off Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

2 (ECU-B P fuse holder) - D15-1 (BATT) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD


b.

Install the ECU-B P fuse.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR