The EV control ECU monitors its internal operation and will store these DTCs when it detects an internal malfunction. If these DTCs are output, replace the EV control ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure | ECU internal malfunction
(EV-CPU error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060687 | Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message | ECU internal malfunction
(Communication error (main to sub CPU)) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060A29 | Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid | ECU internal malfunction
(Sub CPU circuit error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060A44 | Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure | ECU internal malfunction
(Sub CPU RAM error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060A45 | Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure | ECU internal malfunction
(Sub CPU ROM error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060A47 | Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure | ECU internal malfunction
(Sub CPU WDC error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060A49 | Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure | ECU internal malfunction
(Sub CPU calculation check error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060A87 | Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message | ECU internal malfunction
(Communication error (sub to main CPU)) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060B1C | Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range | ECU internal malfunction
(AD conversion error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060B49 | Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure | ECU internal malfunction
(AD timeout error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P060B71 | Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck | ECU internal malfunction
(AD multiplexer error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P1C9E9F | Hybrid/EV System Reset Stuck Off | ECU internal malfunction
(Primary check error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P1CE31C | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range | ECU internal malfunction
(Sub CPU AD conversion error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P1CE349 | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure | ECU internal malfunction
(Sub CPU AD timeout error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
| P1CE371 | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck | ECU internal malfunction
(Sub CPU AD multiplexer error) (1 trip detection logic) |
EV control ECU | Master Warning:
Comes on |
EV | A |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 10 minutes or more.
Turn the ignition switch to ON and wait for 15 seconds or more.
Enter the following menus: Powertrain / EV / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
| Proceed to |
|---|
| NEXT |
NEXT