Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P06B01C  Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range  P06D61C  Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range  P06E61C  Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range  P0A1B00  Drive Motor "A" Control Module Performance  P0A1B04  Drive Motor "A" Control Module System Internal Failure  P1C2B00  Drive Motor "A" Control Module A/D Processing Performance  P1C731C  Sensor Reference Voltage "H" Circuit/Open Circuit Voltage Out of Range  P1CA700  Drive Motor "A" Control Module RAM/ROM Error   P1D0400  FC Air Compressor Motor Control Module A/D Processing Performance  P1D0500  FC Air Compressor Motor Control Module RAM/ROM Error  P1D8F00  FC Air Compressor Motor Control Module Performance  P1D8F04  FC Air Compressor Motor Control Module System Internal Failure  P1D8F47  FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure  P1D8F49  FC Air Compressor Motor Control Module Internal Electronic Failure  P1E3B87  Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message  P1E8D87  Communication Error from Drive Motor "A" to FC Air Compressor Motor Missing Message  


DESCRIPTION

The motor generator control ECU (MG ECU), which is built into the inverter with converter assembly, monitors its internal operation and will store DTCs if the system is malfunctioning. If any of the following DTCs are output, replace the inverter with converter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P06B01C Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range MG ECU internal malfunction:
IPM positive power source error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P06D61C Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range MG ECU internal malfunction:
Standard voltage for analog signal offset (+2.5 V) error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range MG ECU internal malfunction:
IPM negative power source error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P0A1B00 Drive Motor "A" Control Module Performance MG ECU internal malfunction:
R/D converter communication error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P0A1B04 Drive Motor "A" Control Module System Internal Failure MG ECU internal malfunction:
R/D converter NM stop error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1C2B00 Drive Motor "A" Control Module A/D Processing Performance MG ECU internal malfunction:
A/D converter malfunction
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1C731C Sensor Reference Voltage "H" Circuit/Open Circuit Voltage Out of Range MG ECU internal malfunction:
Standard voltage for analog signal (+5 V) error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1CA700 Drive Motor "A" Control Module RAM/ROM Error MG ECU internal malfunction:
CPU ROM-RAM error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1D0400 FC Air Compressor Motor Control Module A/D Processing Performance MG ECU internal malfunction:
A/D converter malfunction
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1D0500 FC Air Compressor Motor Control Module RAM/ROM Error MG ECU internal malfunction:
CPU ROM-RAM error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1D8F00 FC Air Compressor Motor Control Module Performance MG ECU internal malfunction:
R/D converter communication error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1D8F04 FC Air Compressor Motor Control Module System Internal Failure MG ECU internal malfunction:
R/D converter NM stop error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure MG ECU internal malfunction:
Calculation check error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure MG ECU internal malfunction:
Calculation check error
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1E3B87 Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message MG ECU internal malfunction:
Communication error (from FC air compressor motor to drive motor)
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P1E8D87 Communication Error from Drive Motor "A" to FC Air Compressor Motor Missing Message MG ECU internal malfunction:
Communication error (from drive motor to FC air compressor motor)
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P0A1B00 Motor Revolution
P06B01C
P06D61C
P06E61C
P0A1B04
P1C2B00
P1C731C
P1CA700
P1D0400
P1D0500
P1D8F00
P1D8F47
P1D8F49
P1E3B87
P1E8D87
-

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


·

If DTC P06B01C, P06D61C, P06E61C, P1D8F49, P0A1B00, P1D0400, P1C2B00, P1C731C, P1E3B87 or P1E8D87 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the ignition switch to ON and wait for 5 seconds or more.

(b)

Enter the following menus: Powertrain / EV / Utility / All Readiness.

(c)

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




·

If DTC P1D0500 or P1CA700 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the ignition switch to ON and wait for 1 minute or more.

(b)

Enter the following menus: Powertrain / EV / Utility / All Readiness.

(c)

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




·

If DTC P1D8F04 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Enter the following menus: Powertrain / EV / Data List / FC Work Mode, FC Intermittent Operation.

(b)

The shift state is changed from park (P), turn the ignition switch to ON (READY) and wait until the FC system is activated. Waiting for at least 2 minutes is required after turning the ignition switch to ON (READY).

FC system is activated: Data List shows that "FC Work Mode" is "Working" and "FC Intermittent Operation" is "OFF".


(c)

Depress the accelerator pedal, and keep the Data List item "FC Intermittent Operation" as "OFF" (FC air compressor runs) for 30 seconds or more.

(d)

Enter the following menus: Powertrain / EV / Utility / All Readiness.

(e)

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




·

If DTC P0A1B04 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the ignition switch to ON (READY).

(b)

Drive the vehicle at 5 km/h (3 mph) or more for 30 seconds or more.

(c)

Enter the following menus: Powertrain / EV / Utility / All Readiness.

(d)

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.





CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

COMPLETED