Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0B231C  Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU detects a VB sensor malfunction.

The cause of this malfunction may be one of the following:

Battery ECU assembly VB sensor internal circuit malfunction
·

Battery ECU assembly malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction

EV supply battery assembly malfunction



DESCRIPTION

The battery ECU assembly sends EV battery voltage information to the EV control ECU via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range Battery ECU assembly malfunction:
When not boosting, difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is large and difference between "Hybrid/EV Battery Voltage" and "VH-Voltage after Boosting" is large.
(1 trip detection logic)
Battery ECU assembly Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P0B231C
·

Hybrid/EV Battery Voltage

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Boost Ratio



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY).

4.

Push the P position switch (shift position indicator) to select park (P), depress the accelerator pedal to raise the "Hybrid/EV Battery SOC" to a sufficient level.

5.

Check that the FC system is stopped and move the shift lever to select shift state neutral (N).

6.

Set the A/C for maximum cooling.

7.

Leave the vehicle for a few minutes.

HINT:

After the repair if "VL-Voltage before Boosting" and the "Hybrid/EV Battery Voltage" are approximately the same when the ignition switch is turned to ON (READY) with park (P) selected and the accelerator pedal not depressed, the condition is judged as normal.


8.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

If the battery ECU assembly has been replaced, it is necessary to confirm the voltage of each battery block. With ignition switch ON (READY), park (P) selected, the engine stopped and the EV supply battery assembly voltage 226.8 V or more, check the value of Data List items "Hybrid/EV Battery Voltage", "VL-Voltage before Boosting" and "VH-Voltage after Boosting". When the system is normal, the values of "Hybrid/EV Battery Voltage", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" should be almost equal. If the difference between each value is more than the voltages specified below, the system is malfunctioning.

Inspection Voltage Maximum Voltage Difference
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" 26 V
Difference between "Hybrid/EV Battery Voltage" and "VH-Voltage after Boosting" 26 V
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" 42 V



PROCEDURE

1.CHECK DTC OUTPUT (EV, EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P0B231C only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of hybrid battery system in the tables below are output. C


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B16 Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Power source circuit malfunction Hybrid control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range
U011187 Lost Communication with Clearance Sonar Module Missing Message
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Above Threshold
P0E3116 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold
Hybrid battery system P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range

HINT:
·

P0B231C may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C