Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY ECU
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0457183 BATTERY ECU A

HYBRID / BATTERY CONTROL  BATTERY ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A479058N11
6.417,0.167 6.917,0.167 false 1.698,0.813 2.146,0.813 false 5.969,0.021 6.583,0.469 0.615,0.448 18 false 1, 2 1.49,0.688 1.865,1.125 0.375,0.438 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WHEN REPLACING BATTERY ECU ASSEMBLY - (Click here) - -
2 PRECAUTION - (Click here) - -
3 SERVICE PLUG GRIP G3834 - - -

A481588N03
5.229,1.729 6.323,1.958 1.094,0.229 0.958,1.844 0.958,1.271 false 2.646,2.708 2.646,2.135 false 4.885,2.531 5.323,2.365 5.323,2.365 5.479,2.365 false 6.51,0.219 6.833,0.219 false 4.552,2.083 4.552,1.833 4.552,1.833 5.219,1.833 false 4.854,2.052 4.854,1.833 false 2.552,4.979 4.969,4.979 true 2.573,2.771 2.854,3.125 0.281,0.354 18 false 4 0.875,1.938 1.156,2.292 0.281,0.354 18 false 5 4.083,0.969 4.365,1.323 0.281,0.354 10 false x 6 5.531,3.115 5.813,3.469 0.281,0.354 10 false x 2 5.74,2.313 6.292,2.688 0.552,0.375 18 false 7, 9 6.26,0.115 6.542,0.469 0.281,0.354 18 false 8 5.333,1.781 6.417,2.063 1.083,0.281 8 false 8.0 (82, 71 in.*lbf) 2.24,4.865 2.521,5.219 0.281,0.354 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

4 UPPER RADIATOR SUPPORT SEAL 53292A - - -
5 FC STACK COVER SUB-ASSEMBLY 1A906 - - -
6 FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) G9200A (Click here) - -
7 REMOVE CONNECTOR COVER ASSEMBLY - (Click here) - -
8 CHECK TERMINAL VOLTAGE - (Click here) - -
9 INSTALL CONNECTOR COVER ASSEMBLY - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

A479332N10
4.063,0.813 4.458,0.292 4.458,0.292 4.708,0.292 false 4.792,0.177 5.208,0.552 0.417,0.375 18 false 10

Procedure Part Name Code
Z101186

Z101188

Z101187

10 EV SUPPLY BATTERY ASSEMBLY G9510B - - -

A479418N05
2.594,5.115 3.125,5.115 false 5.125,4.688 5.396,4.688 false 1.813,1.25 2.25,1.25 false 4.885,0.75 5.167,0.417 5.167,0.417 5.417,0.417 false 2.625,1.125 3.177,1.479 0.552,0.354 18 false 13 3.49,4.969 4.042,5.323 0.552,0.354 18 false 11 4.833,4.583 5.385,4.938 0.552,0.354 18 false 12 5.708,0.271 6.26,0.625 0.552,0.354 18 false 14 0.677,1.208 0.99,1.406 0.313,0.198 10 false x 2 1.552,0.323 1.865,0.521 0.313,0.198 10 false x 4 0.26,4.604 0.573,4.802 0.313,0.198 10 false x 8 6.156,3.073 6.469,3.271 0.313,0.198 10 false x 4 6.771,4.563 7.083,4.76 0.313,0.198 10 false x 2 4.26,0.24 4.573,0.438 0.313,0.198 10 false x 4 6.594,1.083 6.906,1.281 0.313,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

11 UPPER EV BATTERY COVER PANEL G92N1B (Click here) - -
12 NO. 2 EV BATTERY SHIELD SUB-ASSEMBLY G920RB (Click here) - -
13 NO. 1 EV BATTERY SHIELD SUB-ASSEMBLY G920QB (Click here) - -
14 UPPER NO. 1 EV BATTERY COVER SUB-ASSEMBLY G920LC (Click here) - -

A477102N03
4.906,2.521 5.073,2.521 5.073,2.521 5.219,2.281 false 3.531,1.042 3.729,0.75 3.729,0.75 3.896,0.75 false 4.385,1.604 4.583,1.313 4.583,1.313 4.75,1.313 false 5.313,2.917 5.479,2.917 5.479,2.917 5.625,2.677 false 1.76,1.24 1.927,1.24 1.927,1.24 2.073,1 false 3.052,2.156 3.135,2.156 3.135,2.156 3.229,1.833 false 3.125,0.438 3.438,0.635 0.313,0.198 10 false x 4 5.573,1.635 5.885,1.833 0.313,0.198 10 false x 2 4.833,1.24 5.146,1.438 0.313,0.198 10 false *3 2.729,2 3.177,2.385 0.448,0.385 18 false 15 4.542,2.406 4.99,2.792 0.448,0.385 18 false 16 5.083,2.854 5.396,3.052 0.313,0.198 10 false *4 3.99,0.688 4.448,0.948 0.458,0.26 10 false ● *1 1.531,1.177 1.844,1.375 0.313,0.198 10 false *2

Procedure Part Name Code
Z101186

Z101188

Z101187

15 BATTERY VOLTAGE SENSOR (for Upper Side) 89892A (Click here) - -
16 BATTERY ECU ASSEMBLY 89890A (Click here) - -

*1 NO. 1 EV BATTERY PROTECTOR (for Upper Side) *2 WIRE HARNESS (NO. 1 EV SUPPLY STACK SUB-ASSEMBLY) CELL VOLTAGE DETECTION CIRCUIT
*3 NO. 1 EV BATTERY PACK WIRE *4 NO. 2 EV BATTERY PACK WIRE
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during battery ECU assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Battery ECU assembly Perform current sensor offset learning DTCs are stored (Click here)

CAUTION:
·
A340386


·

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

The type of battery ECU assembly to be used varies depending on the vehicle model.

·

If the wrong type of battery ECU assembly is installed, the ignition switch cannot be turned on (READY).

·

After installing the battery ECU assembly, perform the following to check that the ignition switch can be turned on (READY).

-

Turn the ignition switch on (READY).

-

Turn the ignition switch off and wait for 30 seconds or more.

-

Turn the ignition switch on (READY) again.




HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system


·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. WHEN REPLACING BATTERY ECU ASSEMBLY

HV battery learning values are stored in the battery ECU assembly and EV control ECU and are used to detect malfunctions and illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning values from the other ECU and stores them.

Z101186

NOTICE:
·

Do not replace the battery ECU assembly and EV control ECU at the same time as the HV battery learning values will be lost. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.

·

Do not replace the battery ECU assembly or EV control ECU with a used one from another vehicle.




a.

Procedure when replacing both battery ECU assembly and EV control ECU:

i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

Replace either ECU.


iii.

Connect the cable to the negative (-) auxiliary battery terminal.


iv.

Turn the ignition switch on (READY) and wait for 5 minutes or more.


v.

Turn the ignition switch off and disconnect the cable from the negative (-) auxiliary battery terminal.


vi.

Replace the other ECU.


vii.

Connect the cable to the negative (-) auxiliary battery terminal.


viii.

Check that the ignition switch can be turned on (READY).

HINT:

If the battery ECU assembly and EV control ECU are replaced at the same time without following the above procedure, replace either of the ECUs with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.




Hide 2. PRECAUTION

Z101186

Click here(Click here)

Hide 53292A 4.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 1A906 5.REMOVE FC STACK COVER SUB-ASSEMBLY

Hide G9200A 6.DISCONNECT FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY)

Z101186

Click here(Click here)

Hide 7.REMOVE CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 8.CHECK TERMINAL VOLTAGE

Z101186

Click here(Click here)

Hide 9.INSTALL CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide G9510B 10.REMOVE EV SUPPLY BATTERY ASSEMBLY

Hide G92N1B 11.REMOVE UPPER EV BATTERY COVER PANEL

Z101186

Click here(Click here)

Hide G920RB 12.REMOVE NO. 2 EV BATTERY SHIELD SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide G920QB 13.REMOVE NO. 1 EV BATTERY SHIELD SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide G920LC 14.REMOVE UPPER NO. 1 EV BATTERY COVER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 89892A 15.REMOVE BATTERY VOLTAGE SENSOR (for Upper Side)

Z101186

Click here(Click here)

Hide 89890A 16.REMOVE BATTERY ECU ASSEMBLY

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A477142N01
0.396,0.042 1.26,0.479 0.865,0.438 18 true i, ii

i.

Disconnect the 2 connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector



ii.

Remove the 2 nuts and battery ECU assembly.

NOTICE:
·

Do not drop the battery ECU assembly, strike it with tools or subject it to impact.

·

If the battery ECU assembly is subjected to an impact, replace it with a new one.