Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0D2D16  Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold  P0D2D17  Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold  


DESCRIPTION

The inverter contains a three-phase bridge circuit, which consists of 6 power transistors (IGBTs) each for FC air compressor motor and drive motor. The inverter converts high-voltage direct current from the EV supply battery assembly into three-phase alternating current for FC air compressor motor and drive motor; it also converts three-phase alternating current supplied by FC air compressor motor and drive motor into direct current for the EV supply battery assembly. The MG ECU controls the actuation of the power transistors (IGBTs). The inverter transmits information necessary for control, such as amperage and voltage, to the MG ECU.

A478521E01
1.125,4.26 1.448,4.417 0.323,0.156 10 false FVH 0.552,7.333 1.417,7.51 0.865,0.177 10 false Reactor 3.656,0.563 4.479,0.948 0.823,0.385 10 false FC Air Compressor 6.281,8.49 6.521,8.646 0.24,0.156 10 false VB 1.052,4.885 1.229,5.031 0.177,0.146 10 false X 1.052,6.042 1.229,6.188 0.177,0.146 10 false V 1.052,6.604 1.229,6.75 0.177,0.146 10 false U 1.042,5.458 1.219,5.604 0.177,0.146 10 false W 3.771,1.156 3.948,1.302 0.177,0.146 10 false U 4.073,1.177 4.25,1.323 0.177,0.146 10 false V 4.385,1.156 4.563,1.302 0.177,0.146 10 false W 6.25,1.146 6.427,1.292 0.177,0.146 10 false W 5.958,1.167 6.135,1.313 0.177,0.146 10 false V 5.625,1.167 5.802,1.313 0.177,0.146 10 false U 1.521,8.177 1.844,8.333 0.323,0.156 10 false FVL 0.073,8.573 0.844,9.094 0.771,0.521 10 false Inverter with Converter Assembly 2.271,3.521 2.885,3.719 0.615,0.198 10 false FCR 1.292,9.198 2.646,9.427 1.354,0.229 10 false FC Stack Assembly 2.969,8.198 3.979,8.563 1.01,0.365 10 false FCDC Converter Control ECU 3.271,7.25 4.385,7.531 1.115,0.281 10 false FC Control ECU 2.604,5.115 3.344,5.531 0.74,0.417 10 false EV Control ECU 3.823,5.448 4.396,5.635 0.573,0.188 10 false MG ECU 2.979,4.5 3.75,4.698 0.771,0.198 10 false Inverter 4.896,7.313 5.542,7.76 0.646,0.448 10 false DC/DC Converter 5.865,9.156 7.042,9.5 1.177,0.344 10 false EV Supply Battery Assembly 6.24,7.938 6.594,8.125 0.354,0.188 10 false SMR 6.271,6.625 6.531,6.823 0.26,0.198 10 false VL 4.688,6.656 5.708,6.958 1.021,0.302 10 false Boost Converter 5.271,6.125 5.906,6.302 0.635,0.177 10 false Reactor 5.771,4.448 6.031,4.646 0.26,0.198 10 false VH 4.406,1.573 4.906,1.906 0.5,0.333 10 false Current Sensor 6.302,1.573 6.885,1.917 0.583,0.344 10 false Current Sensor 5.719,0.656 6.177,0.844 0.458,0.188 10 false Motor 6.031,7.302 6.51,7.625 0.479,0.323 10 false Current Sensor 0.583,7.719 1.094,8.063 0.51,0.344 10 false Current Sensor

The MG ECU uses an inverter voltage sensor, which is built into the inverter, to detect boosted high voltage (VH) to allow control of the voltage boost.

The inverter voltage sensor outputs voltage that fluctuates between 0 to 5 V according to changes in VH.

The MG ECU monitors the inverter voltage sensor and detects the following malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold Inverter voltage (VH) signal is stuck low:
DTC stored when the VH sensor signal is excessively low.
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold Inverter voltage (VH) signal is stuck high:
DTC stored when the VH sensor signal is excessively high.
(1 trip detection logic)
Inverter with converter assembly Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P0D2D16 VH-Voltage after Boosting
P0D2D17

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.

2.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

3.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.REPLACE INVERTER WITH CONVERTER ASSEMBLY
HINT:
·

The signal line from the inverter voltage (VH) sensor is connected to the MG ECU, which is built into the inverter with converter assembly. If P0D2D16 or P0D2D17 is output, replace the inverter with converter assembly.



Result:
Proceed to
NEXT



NEXT

COMPLETED