Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Brake Override System  


DESCRIPTION

When the vehicle is being driven with the accelerator pedal depressed, depressing the brake pedal without releasing the accelerator pedal will activate the brake override system to restrict FC system output. The conditions for activating the brake override system as well as the items that are controlled are explained below.

C387914E04
0.115,0.073 1.729,0.25 1.615,0.177 10 false Brake Override System: 0.229,1.156 2.49,1.375 2.26,0.219 10 false Accelerator Pedal Sensor Assembly 2.573,0.865 3.698,1.24 1.125,0.375 10 false Actual accelerator opening 5.521,0.875 6.948,1.104 1.427,0.229 10 false Meter display request 2.635,1.99 3.542,2.208 0.906,0.219 10 false Braking torque 5.5,1.698 6.635,2.229 1.135,0.531 10 false FC system output request 5.521,2.563 7.094,2.813 1.573,0.25 10 false Head up display request* 2.635,2.656 3.583,2.865 0.948,0.208 10 false Vehicle Speed 0.438,2.99 2.219,3.208 1.781,0.219 10 false Skid Control ECU Assembly 3.854,3.115 6.219,3.354 2.365,0.24 10 false EV Control ECU 0.073,3.458 1.479,3.656 1.406,0.198 10 false *: w/ Head up display

Activation Conditions:
·

The accelerator pedal and brake pedal are depressed at the same time.

NOTICE:

Brake override control may not be performed depending on the relationship between accelerator opening and vehicle speed.




Items Controlled:
·

Controls FC system output

HINT:
·

When the control is operating, requested FC system output is controlled in accordance with the brake pedal stroke.

·

When the FC system output is reduced to a specified level because the accelerator pedal and brake pedal are depressed at the same time, an indicator is displayed on the meter. (Operation of the system can be confirmed when the indicator is displayed on the meter.)





Deactivation Conditions:
·

The accelerator pedal or brake pedal is released.



CAUTION / NOTICE / HINT

Inspection Method

Drive at 10 km/h (6 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if hybrid system output is controlled when the brake pedal is depressed by the left foot of the driver, it can be confirmed that the brake override system has operated.

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.

Pay careful attention to the surroundings when performing the road test.


HINT:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing a loss of power (driving torque) after the accelerator and brake pedals have both been intentionally depressed, explain that this is not a malfunction, and depressing both the accelerator and brake pedals at the same time should be avoided.



PROCEDURE

1.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Enter the following menus: System Select / Health Check.


b.

Check for DTCs.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



c.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (MASTER CYLINDER CONTROL TORQUE)

B

GO TO DTC CHART

2.READ VALUE USING GTS (MASTER CYLINDER CONTROL TORQUE)
a.

Enter the following menus: Powertrain / EV / Data List / Master Cylinder Control Torque.

Powertrain > EV > Data List
Tester Display
Master Cylinder Control Torque
50003 397 89
Powertrain > EV > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Control Torque Braking torque equivalent to master cylinder brake fluid pressure Total braking torque Master cylinder brake fluid pressure control torque = hydraulic brake control torque + rear regenerative brake torque - Brake pedal depressed:
Changes with the brake pedal pressure
Master cylinder pressure sensor
Result:
Result Proceed to
Display changes according to brake pedal depression force. A
Display does not change according to brake pedal depression force. B



b.

Turn the ignition switch off.



A

3.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

B

CHECK BRAKE MASTER CYLINDER ASSEMBLY

3.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)
a.

Read the value of "Accelerator Position Sensor No. 1 Voltage %" and "Accelerator Position Sensor No. 2 Voltage %" displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage %
Accelerator Position Sensor No.2 Voltage %
50003 397 23,24
HINT:

If the Data List updates slowly, perform measurement after selecting only the "Accelerator Position Sensor No.1 Voltage %" and "Accelerator Position Sensor No.2 Voltage %" items.


Standard:
Inspection Condition Specified Condition
Accelerator pedal fully released → fully depressed Value (%) changes with accelerator pedal operation



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (VEHICLE SPEED)

NG

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

4.READ VALUE USING GTS (VEHICLE SPEED)
a.

Read the value of "Vehicle Speed" displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Vehicle Speed
50003 397 12
HINT:

If the Data List updates slowly, perform measurement after selecting only the "Vehicle Speed" item.


Standard:
Inspection Condition Specified Condition
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph))
No large fluctuations in displayed speed


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)

5.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Read the value of "FR Wheel Speed", "FL Wheel Speed", "RR Wheel Speed" and "RL Wheel Speed" displayed on the GTS.

Chassis > Brake/EPB > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 435 13,14,15,16
HINT:

If the Data List updates slowly, perform measurement after selecting only the "FR Wheel Speed", "FL Wheel Speed", "RR Wheel Speed" and "RL Wheel Speed" items.


Standard:
Inspection Condition Specified Condition
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph))
No large fluctuations in displayed speed


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

END

NG