The cause of the malfunction may be the cooling system.
Check whether the grille is blocked, whether coolant is leaking, the EV radiator fan operating condition and whether coolant has frozen.
| Area | Inspection |
|---|---|
| Grille blockage, coolant amount, coolant hoses, EV radiator fan | Check for overheating due to EV cooling system malfunction. |
| Inverter coolant temperature sensor (built-in inverter) | Check for temperature sensor malfunction. |
| Coolant freezing check | Check freeze frame values to determine whether the hybrid coolant was frozen when the DTC was stored. |
| Data List |
|---|
·
Inverter Coolant Water Temperature ·
Motor Inverter Temperature ·
Generator Inverter Temperature ·
Boosting Converter Temperature (Upper) ·
Boosting Converter Temperature (Lower) ·
Ambient Temperature |
The inverter built inside the PCU and the inverter for the auxiliary pump convert the high-voltage direct current of the EV supply battery into alternating current for the drive motor, FC air compressor with motor, FC cooling water pump or hydrogen recirculation pump. The inverters generate heat during the conversion process. Therefore, the inverters are cooled by a special cooling system consisting of the water with motor pump assembly, the cooling fan, and a radiator. This cooling system is independent of the FC stack cooling system. The EV control ECU monitors the water with motor pump assembly, the cooling fan and cooling system, and detects malfunctions.
| *A | for LHD | - | - |
| *1 | Water with Motor Pump Assembly | *2 | Inverter Reserve Tank Assembly |
| *3 | Inverter with Converter Assembly | *4 | Radiator Assembly (EV) |
| *5 | FC Air Compressor with Motor Assembly | *6 | FC Converter Assembly |
| *A | for RHD | - | - |
| *1 | Water with Motor Pump Assembly | *2 | Inverter Reserve Tank Assembly |
| *3 | Inverter with Converter Assembly | *4 | Radiator Assembly (EV) |
| *5 | FC Air Compressor with Motor Assembly | *6 | FC Converter Assembly |
This step is referenced from the procedures for each DTC.
If the inspection results below are normal, perform the next procedure for the referenced DTC.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.
Make sure to remove the service plug grip first.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the EV supply battery assembly
Disconnecting the low voltage connector of the FC converter assembly
To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.
The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.
Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.
| *a | Without waiting for 10 minutes |
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.
Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.
If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.
After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
Pre-procedure1
Make sure that the front side of the radiator grille is not blocked with anything.
Procedure1
Ask the customer if the front side of the radiator grille was blocked with anything.
| Result | Proceed to |
|---|---|
| Not blocked. | A |
| Is/was blocked. | B |
If the radiator grille is blocked, the inverter coolant temperature will increase and this DTC may be stored.
Post-procedure1
None.
A
B
Pre-procedure1
Check the EV coolant level in the inverter reserve tank.
Procedure1
Check for EV coolant leaks.
| Result | Proceed to |
|---|---|
| No leaks are found and the EV coolant level in the inverter reserve tank assembly is above the low line. | A |
| No leaks are found and the EV coolant level in the inverter reserve tank assembly is below the low line. | B |
| EV coolant leaks are evident. | C |
After repairing the EV coolant leaks and adding coolant, perform the Active Tests "Activate the Inverter Water Pump" and "Control the Radiator Fan 1" and make sure that there are no malfunctions.
If there are signs of coolant leakage around the connecting parts of a hose and the inverter with converter assembly, replace the hose with a new one.
Post-procedure1
None.
A
B
C
Check that the cooling system hoses are not kinked or clogged.
The cooling system hoses are not kinked or clogged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the "Control the Radiator Fan 1" Active Test.
| Tester Display |
|---|
| Control the Radiator Fan 1 |
| Result | Proceed to |
|---|---|
| Cooling fan operates | A |
| Cooling fan stops | B |
A
B
Pre-procedure1
Turn the ignition switch off and wait for 1 hour or more.
Procedure1
Read the Data List with the engine stopped.
| Tester Display |
|---|
| Motor Inverter Temperature |
| Boosting Converter Temperature (Upper) |
| Boosting Converter Temperature (Lower) |
| Inverter Coolant Water Temperature |
| FC Air Compressor Inverter Temperature |
| Result | Proceed to |
|---|---|
| Other than below. | A |
| "Inverter Coolant Water Temperature" value is higher than the displayed temperature of any other Data List item by 20°C (68°F) or more. | B |
The lower limit temperature that can be displayed for "FC Air Compressor Inverter Temperature", "Motor Inverter Temperature", "Boosting Converter Temperature (Upper)" and "Boosting Converter Temperature (Lower)" is 15°C (59°F). The lower limit temperature for "Inverter Coolant Water Temperature" is -40°C (-40°F). The "Inverter Coolant Water Temperature" value displayed on the GTS may be lower than the others, but this is not a malfunction.
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
None.
Procedure1
Check for DTCs.
Read the freeze frame data item Ambient Temperature using the GTS.
Check if the freeze frame data item Ambient Temperature is below the freezing temperature of the EV coolant.
| Result | Proceed to |
|---|---|
| Ambient Temperature value is above freezing temperature of the EV coolant. | A |
| Ambient Temperature value is below freezing temperature of the EV coolant. | B |
EV coolant (SLLC) with a 30% concentration freezes at -15°C (5°F) and EV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).
If the EV coolant freezes in the EV radiator or water with motor pump, the coolant temperature in the water with motor pump assembly rises because the EV coolant cannot circulate. As a result, a DTC may be stored.
A DTC is stored when the water with motor pump impeller cannot rotate due to freezing of the EV coolant.
If DTCs are output due to freezing of the LLC, the problem symptom cannot be reproduced. Check the LLC replacement history and whether the LLC was frozen based on the ambient temperature when the DTCs were stored.
Post-procedure1
Turn the ignition switch off.
A
B