Home › ADAS / AD › ADVANCED PARK › ADVANCED PARK
RM37H0E _95 ADAS / AD _095318 ADVANCED PARK _0455116 ADVANCED PARK J

ADVANCED PARK  ADVANCED PARK  Main Switch Circuit  


DESCRIPTION

When the advanced park main switch is turned on, a signal is sent to the clearance warning ECU assembly. The advanced park operates according to this signal.

WIRING DIAGRAM

E338895E11
2.813,1.115 5.229,1.542 2.417,0.427 10 false Advanced Park Main Switch 5.458,1.833 6.719,2.292 1.26,0.458 10 false Clearance Warning ECU Assembly 5.656,0.542 6.219,0.708 0.563,0.167 10 false ISSW 5.458,1.667 6.021,1.833 0.563,0.167 10 false G20 5.396,0.427 5.958,0.594 0.563,0.167 10 false 11 2.948,0.427 3.51,0.594 0.563,0.167 10 false 5 4.25,0.427 4.813,0.594 0.563,0.167 10 false 2 4.031,0.438 4.594,0.604 0.563,0.167 10 false E 3.146,0.438 3.708,0.604 0.563,0.167 10 false IG 2.813,0.969 3.375,1.135 0.563,0.167 10 false D6 0.146,0.542 1.24,0.938 1.094,0.396 10 false from IG1 D NO.1 Relay 1.875,0.688 2.979,0.927 1.104,0.24 10 false IG1 D NO.1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List to check the ECU data.

Body Electrical > Clearance Warning > Data List
Tester Display Measurement Item Range Normal Condition
Advanced Park Main Switch Press Status Advanced park main switch input signals OFF/ON OFF; Advanced park main switch off
ON: Advanced park main switch on
OK:

The Data List changes in response to the operation of the advanced park main switch.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ADVANCED PARK MAIN SWITCH
2.INSPECT ADVANCED PARK MAIN SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (ADVANCED PARK MAIN SWITCH - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPLACE ADVANCED PARK MAIN SWITCH

3.CHECK HARNESS AND CONNECTOR (ADVANCED PARK MAIN SWITCH - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the D6 advanced park main switch connector.


b.

Disconnect the G20 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G20,D6)Location & Routing

Click Connector(G20)Body>Floor Wire / No. 3 Floor Wire>Clearance Warning ECU Assembly

Click Connector(D6)Instrument Panel>Instrument Panel Wire>Advanced Parking Switch Assembly

G20-11 (ISSW) - D6-2 (E) Always Below 1 Ω
G20-11 (ISSW) or D6-2 (E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ADVANCED PARK MAIN SWITCH - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ADVANCED PARK MAIN SWITCH - AUXILIARY BATTERY)
a.

Disconnect the D6 advanced park main switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D6)Location & Routing

Click Connector(D6)Instrument Panel>Instrument Panel Wire>Advanced Parking Switch Assembly

D6-5 (IG) - Body ground Ignition switch ON 11 to 14 V
D6-5 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR