Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY
RM37H0E _58 Vehicle Interior _095297 SEAT BELT _0448142 REAR SEAT OUTER BELT ASSEMBLY N

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a rear seat outer belt assembly with a pretensioner that has not been deployed.

·

The rear seat outer belt assembly produces an exploding sound when the pretensioner deploys, so perform the operation outdoors where it will not disturb local residents.

·

When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

·

When deploying a seat belt pretensioner, perform the operation at least 10 m (32.8 ft.) away from the vehicle.

·

The rear seat outer belt assembly becomes extremely hot when the pretensioner is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a rear seat outer belt assembly with a deployed pretensioner.

·

Do not apply water, etc. to a rear seat outer belt assembly with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with a seat belt pretensioner or disposing of a rear seat outer belt assembly with a seat belt pretensioner, always deploy the seat belt pretensioner first in accordance with the procedure described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the Service Department of the distributor.


Hide 2.DISPOSE OF REAR SEAT OUTER BELT ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of a rear seat outer belt assembly with a pretensioner, never deploy the pretensioner in the customer's vehicle.

·

Be sure to observe the following procedure when deploying a seat belt pretensioner.



HINT:

Prepare an auxiliary battery as the power source to deploy the seat belt pretensioner.


a.
B383955N01
0.656,0.927 0.906,1.177 false 0.365,0.833 0.823,1.031 0.458,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying a seat belt pretensioner, always use the specified SST.


i.
B383956C13
2.229,0.823 2.646,0.823 false 1.24,1.833 1.573,1.833 false 2.688,0.729 3,0.885 0.313,0.156 10 false *a 1.646,1.75 2.063,2 0.417,0.25 10 false SST
*a Auxiliary Battery


Connect the red clip of SST to the positive (+) auxiliary battery terminal and the black clip to the negative (-) auxiliary battery terminal.

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



ii.
B383957N01
1.948,1.031 2.448,1.031 false 2.51,0.948 2.969,1.146 0.458,0.198 10 false SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.



iii.

Disconnect SST from the auxiliary battery.




c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B394718

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.




d.

Disconnect the seat belt pretensioner connector.

i.

Remove the roof side rail garnish assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY>REMOVAL


ii.
B602719C01
0,0 0,0 false
V100135

Pretensioner Connector
V113147

Release in this Direction


Using a thin-bladed screwdriver, release the lock as shown in the illustration and disconnect the pretensioner connector.

HINT:

Tape the thin-bladed screwdriver tip before use.




e.

Check the rear seat outer belt assembly.

CAUTION:
·
B460287

Do not activate the pretensioner if the rear seat outer belt assembly is loose.

·

If the pretensioner is activated when the rear seat outer belt assembly is loose, the rear seat outer belt assembly may move out of position and cause unexpected injuries.

·
B460288

Do not activate the pretensioner if the rear seat outer belt assembly is loose.

·

If the pretensioner is activated when the rear seat outer belt assembly is loose, the rear seat outer belt assembly may move out of position and cause unexpected injuries.




f.
B602720N01
1.479,2.771 1.604,1.906 true 2.854,2.76 2.677,1.906 true 1.333,2.802 1.792,3 0.458,0.198 10 false SST 2.75,2.792 3.208,2.99 0.458,0.198 10 false SST

Connect SST.

i.

After connecting the following SST to each other, and then connect them to the seat belt pretensioner.

SST
09082-00700  
09082-00802  (09082-10801, 09082-20801)

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the pretensioner connector.



ii.
C154370C15
0.688,0.875 1.094,0.875 false 1.615,1.813 1.917,2.063 0.302,0.25 10 *a 0.385,0.802 0.844,1 0.458,0.198 10 SST
*a 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

CAUTION:
·
B394904

Do not perform deployment with any of the doors or windows open.

·

If deployment is performed with any of the doors or windows open, dust and gas may enter the eyes or be breathed in.




iii.

Close all of the doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.




g.

Deploy the seat belt pretensioner.

i.
B411731

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Connect the red clip of SST to the positive (+) auxiliary battery terminal and the black clip to the negative (-) auxiliary battery terminal.


iii.

Press the SST activation switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time the LED of SST illuminates.


CAUTION:
·

The rear seat outer belt assembly produces an exploding sound when the pretensioner is deployed, so perform the operation outdoors where it will not disturb nearby residents.

B460351

·

If this procedure is performed indoors or on a rough road where safety cannot be ensured, unforeseen injuries may occur. Also, if this procedure is performed near a residential area, the deployment noise may disturb nearby residents.





h.

Dispose of the rear seat outer belt assembly.

i.

Remove the rear seat outer belt assembly and SST.


ii.

Place the rear seat outer belt assembly in a plastic bag, tie the end tightly, and dispose of it according to local regulations.

CAUTION:
·
B479326

The rear seat outer belt assembly becomes extremely hot when the pretensioner is deployed, so do not touch it for at least 30 minutes after deployment.

·
B479327

Do not apply water, etc. to a rear seat outer belt assembly with a deployed pretensioner.

·

If water is applied to the rear seat outer belt assembly immediately after deployment, burns may be caused by the resulting steam.

·
B479328

Always wear safety glasses and gloves when handling a rear seat outer belt assembly with a deployed pretensioner.

·

If a rear seat outer belt assembly with a deployed pretensioner is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·

After removal, quickly seal the rear seat outer belt assembly in a plastic bag.

·
B395355

Never dispose of a rear seat outer belt assembly with a pretensioner that has not been deployed.

·

If a rear seat outer belt assembly with a pretensioner that has not been deployed is disposed of, and then deploys accidentally, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle, deploy the seat belt pretensioner, and then scrap the vehicle with the rear seat outer belt assembly installed.




Hide 3.DISPOSE OF REAR SEAT OUTER BELT ASSEMBLY (When Not Installed in Vehicle)

NOTICE:
·

When disposing of a rear seat outer belt assembly with a pretensioner, never deploy the pretensioner in the customer's vehicle.

·

Be sure to observe the following procedure when deploying a seat belt pretensioner.



HINT:

Prepare an auxiliary battery as the power source to deploy the seat belt pretensioner.


a.
B383955N01
0.656,0.927 0.906,1.177 false 0.365,0.833 0.823,1.031 0.458,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying a seat belt pretensioner, always use the specified SST.


i.
B383956C14
2.229,0.823 2.646,0.823 false 1.24,1.833 1.573,1.833 false 2.688,0.729 3,0.885 0.313,0.156 10 false *a 1.646,1.75 2.063,2 0.417,0.25 10 false SST
*a Auxiliary Battery


Connect the red clip of SST to the positive (+) auxiliary battery terminal and the black clip to the negative (-) auxiliary battery terminal.

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



ii.
B383957N01
1.948,1.031 2.448,1.031 false 2.51,0.948 2.969,1.146 0.458,0.198 10 false SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.



iii.

Disconnect SST from the auxiliary battery.




c.

Remove the rear seat outer belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY>REMOVAL


d.
B602711C02
0.76,1 1.073,1.156 0.313,0.156 10 false *a 1.292,0.688 1.604,0.844 0.313,0.156 10 false *b
*a Cut
*b 100 mm (3.94 in.)


Wind the seat belt webbing with the retractor.


e.

When the seat belt webbing is sufficiently wound, cut the seat belt webbing approximately 100 mm (3.94 in.) from the retractor as shown in the illustration.

HINT:

The retractor resistance increases in correlation with how much the seat belt webbing is wound.



f.
B602720N02
1.479,2.771 1.604,1.906 true 2.854,2.76 2.677,1.906 true 1.333,2.802 1.792,3 0.458,0.198 10 false SST 2.75,2.792 3.208,2.99 0.458,0.198 10 false SST

Connect SST.

i.

After connecting the following SST to each other, connect them to the seat belt pretensioner.

SST
09082-00700  
09082-00802  (09082-10801, 09082-20801)

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the pretensioner connector.



ii.
B104882C91
2.854,0.99 3.094,1.167 0.24,0.177 10 false *a
*a Wire Diameter
V100155

Stripped Wire


Using braided wire, tie down the rear seat outer belt assembly to 2 unneeded tires.

Wire:

Cross-sectional area of stripped wire

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the rear seat outer belt assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the cross-sectional area of stripped wire:

Area = 3.14 x (Diameter)2 / 4



iii.
B602721N01
1.396,1.896 1.354,1.531 false 2.573,1.531 2.875,1.906 true 1.281,1.927 1.594,2.125 0.313,0.198 10 false SST 2.802,1.948 3.156,2.146 0.354,0.198 10 false SST

Place the rear seat outer belt assembly with 2 unneeded tires on the ground.

NOTICE:
·

Position the rear seat outer belt assembly as shown in the illustration.

·

The tire and wheel assembly may be damaged by the seat belt pretensioner deployment, so use an unneeded tire and wheel assembly.




iv.

Move SST at least 10 m (32.8 ft.) away from the tire and wheel assembly.

NOTICE:

Take care not to damage the SST wire harness.




g.
B383100C01
1.188,1.938 1.5,2.094 0.313,0.156 10 false *a
*a 10 m (32.8 ft.) or more


Deploy the seat belt pretensioner.

i.

Check that no one is within a 10 m (32.8 ft.) radius of the tire and wheel assembly.


ii.

Connect the red clip of SST to the positive (+) auxiliary battery terminal and the black clip to the negative (-) auxiliary battery terminal.


iii.

Press the SST activation switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time the LED of SST illuminates.


CAUTION:
·

The rear seat outer belt assembly produces an exploding sound when the pretensioner is deployed, so perform the operation outdoors where it will not disturb nearby residents.

B411732

·

If this procedure is performed indoors or on a rough road where safety cannot be ensured, unforeseen injuries may occur. Also, if this procedure is performed near a residential area, the deployment noise may disturb nearby residents.





h.

Dispose of the rear seat outer belt assembly.

i.

Remove the tire and wheel assembly and SST.


ii.

Place the rear seat outer belt assembly in a plastic bag, tie the end tightly, and dispose of it according to local regulations.

CAUTION:
·
B395352

The rear seat outer belt assembly becomes extremely hot when the pretensioner is deployed, so do not touch it for at least 30 minutes after deployment.

·
B395353

Do not apply water, etc. to a rear seat outer belt assembly with a deployed pretensioner.

·

If water is applied to the rear seat outer belt assembly immediately after deployment, burns may be caused by the resulting steam.

·
B395354

Always wear safety glasses and gloves when handling a rear seat outer belt assembly with a deployed pretensioner.

·

If a rear seat outer belt assembly with a deployed pretensioner is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·

After removal, quickly seal the rear seat outer belt assembly in a plastic bag.

·
B395355

Never dispose of a rear seat outer belt assembly with a pretensioner that has not been deployed.

·

If a rear seat outer belt assembly with a pretensioner that has not been deployed is disposed of, and then deploys accidentally, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.