Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY
RM37H0E _58 Vehicle Interior _095297 SEAT BELT _0448142 REAR SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B601537N03
1.5,5.417 1.5,5.271 false 0.458,4.667 0.458,5.417 0.458,5.417 1.74,5.417 false 2.583,3.771 1.938,3.771 false 1.417,2.25 1.094,2.25 false 5.813,2.396 5.365,2.396 false 2.208,2.646 1.885,2.646 false 6.667,4.552 6.344,4.552 false 6.594,0.25 5.01,0.25 false 5.667,0.604 5.667,0.25 false 6.375,0.99 6.375,0.25 false 0.958,0.208 0.354,0.208 false 0.99,0.719 0.385,0.719 false 1.958,5.26 2.208,5.573 0.25,0.313 18 false 4 1.781,5.313 1.938,5.51 0.156,0.198 10 false ● 1,0.052 1.25,0.365 0.25,0.313 18 false 1 6.063,2.271 6.313,2.583 0.25,0.313 18 false 5 6.688,4.448 7,4.646 0.313,0.198 10 false *1 1.448,2.146 1.76,2.344 0.313,0.198 10 false *2 2.229,2.542 2.542,2.74 0.313,0.198 10 false *3 6.635,0.146 6.792,0.344 0.156,0.198 10 false ● 6.813,0.083 7.031,0.396 0.219,0.313 18 false 6 2.688,2 3,2.198 0.313,0.198 10 false x 4 1.031,0.552 1.281,0.865 0.25,0.313 18 false 2 2.833,3.635 3.083,3.948 0.25,0.313 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 BENCH TYPE REAR SEAT CUSHION ASSEMBLY - (Click here) - -
4 REAR SEAT CUSHION LOCK HOOK 72693 - - -
5 BENCH TYPE REAR SEATBACK ASSEMBLY - (Click here) - -
6 REAR SEATBACK HOLDER 71398A - - -

*1 REAR SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) *2 REAR SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
*3 REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (FLOOR ANCHOR) - -
● Non-reusable part - -

B601538N10
0.542,3.052 0.542,2.844 false 3.01,4.458 3.656,4.458 false 0.729,0.927 0.969,0.927 false 5.885,3.76 6.26,3.76 false 1.313,1.281 1.688,1.281 false 4.656,3.281 5.031,3.281 false 3.729,1.281 3.729,1.573 false 4.698,1.656 4.698,1.948 false 2.802,0.917 2.802,1.208 false 5.719,2.438 5.354,2.438 false 2.177,0.344 1.813,0.344 false 3.344,0.24 2.979,0.24 false 4.677,0.135 4.313,0.135 false 5.333,0.323 4.969,0.323 false 4.75,1.063 4.75,0.677 false 5.521,1.188 5.948,1.188 false 6.521,1.677 6.521,1.833 6.521,1.833 6.219,1.833 false 7.01,1.896 7.01,1.552 false 6.635,2.365 6.635,2.104 false 6.5,3.177 6.5,2.833 false 2.604,1.667 2.75,1.667 2.75,1.667 2.75,1.813 false 4.01,3.229 4.01,2.938 false 0.938,3.573 1.229,3.573 false 1.781,4.073 2.052,4.073 false 2.781,4.313 2.99,4.615 0.208,0.302 18 false 7 0.479,3.073 0.698,3.365 0.219,0.292 18 false 8 6.51,3.625 6.708,3.938 0.198,0.313 18 false 9 0.354,0.781 0.719,1.115 0.365,0.333 18 false 10 5.063,3.115 5.375,3.427 0.313,0.313 18 false 11 0.938,1.135 1.292,1.427 0.354,0.292 18 false 12 4.552,1.979 4.948,2.313 0.396,0.333 18 false 13 3.573,1.594 3.948,1.906 0.375,0.313 18 false 14 4.979,2.271 5.333,2.594 0.354,0.323 18 false 15 2.656,1.229 2.979,1.531 0.323,0.302 18 false 16 1.635,0.25 1.792,0.448 0.156,0.198 10 false ● 3.375,0.135 3.531,0.333 0.156,0.198 10 false ● 4.708,0.031 4.865,0.229 0.156,0.198 10 false ● 5.365,0.219 5.521,0.417 0.156,0.198 10 false ● 5.146,1.031 5.5,1.333 0.354,0.302 18 false 17 4.604,1.083 4.938,1.417 0.333,0.333 18 false 18 6.052,1.729 6.208,1.927 0.156,0.198 10 false ● 6.969,1.906 7.125,2.104 0.156,0.198 10 false ● 6.594,2.375 6.75,2.573 0.156,0.198 10 false ● 6.458,3.188 6.615,3.385 0.156,0.198 10 false ● 4.104,3.26 4.427,3.563 0.323,0.302 18 false 19 2.24,1.542 2.594,1.865 0.354,0.323 18 false 20 1.448,3.938 1.771,4.24 0.323,0.302 18 false 21 0.583,3.417 0.906,3.719 0.323,0.302 18 false 22 0.396,3.469 0.552,3.667 0.156,0.198 10 false ● 1.25,3.99 1.406,4.188 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

7 REAR DOOR SCUFF PLATE INSIDE LH 67918F - - -
8 REAR DOOR SCUFF PLATE INSIDE RH 67917F - - -
9 REAR DOOR OPENING TRIM WEATHERSTRIP LH 62332A (Click here) - -
10 REAR DOOR OPENING TRIM WEATHERSTRIP RH 62331A (Click here) - -
11 REAR SEAT SIDE GARNISH LH 62552F - - -
12 REAR SEAT SIDE GARNISH RH 62551F - - -
13 INNER ROOF SIDE GARNISH COVER LH 62488A - - -
14 INNER ROOF SIDE GARNISH COVER RH 62487A - - -
15 INNER ROOF SIDE GARNISH ASSEMBLY LH 62480A - - -
16 INNER ROOF SIDE GARNISH ASSEMBLY RH 62470A - - -
17 ROOF SIDE RAIL GARNISH ASSEMBLY LH 62440 - - -
18 ROOF SIDE RAIL GARNISH ASSEMBLY RH 62430 - - -
19 REAR SEAT OUTER BELT ASSEMBLY LH 73370E (Click here) - -
20 REAR SEAT OUTER BELT ASSEMBLY RH 73360D (Click here) - -
21 REAR SEAT BELT RETRACTOR CUSHION LH 73439 (Click here) - -
22 REAR SEAT BELT RETRACTOR CUSHION RH 73439 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Move both front seats to the frontmost position and fold them forward.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B401522

Be sure to read precaution thoroughly before servicing.

(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

Hide 3.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Z101186

(Click here)

Hide 72693 4.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 5.REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY

Z101186

(Click here)

Hide 71398A 6.REMOVE REAR SEATBACK HOLDER

Hide 67918F 7.REMOVE REAR DOOR SCUFF PLATE INSIDE LH

Hide 67917F 8.REMOVE REAR DOOR SCUFF PLATE INSIDE RH

a.

Use the same procedure described for the LH side.


Hide 62332A 9.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Z101186

HINT:

Remove a part of the rear door opening trim weatherstrip LH so that the rear seat side garnish LH and inner roof side garnish assembly LH can be removed.



Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>REMOVAL

Hide 62331A 10.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.

Use the same procedure described for the LH side.


Hide 62552F 11.REMOVE REAR SEAT SIDE GARNISH LH

Hide 62551F 12.REMOVE REAR SEAT SIDE GARNISH RH

a.

Use the same procedure described for the LH side.


Hide 62488A 13.REMOVE INNER ROOF SIDE GARNISH COVER LH

Hide 62487A 14.REMOVE INNER ROOF SIDE GARNISH COVER RH

a.

Use the same procedure described for the LH side.


Hide 62480A 15.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

Hide 62470A 16.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

a.

Use the same procedure described for the LH side.


Hide 62440 17.REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

Hide 62430 18.REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

a.

Use the same procedure described for the LH side.


Hide 73370E 19.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH

a.
B600232C02
1.313,0.156 1.448,0.448 0.135,0.292 18 true i 6.208,0.375 6.396,0.667 0.188,0.292 18 true ii 1.542,2.594 1.729,2.885 0.188,0.292 18 true ii 4.156,1.417 4.375,1.698 0.219,0.281 18 true iii 1.198,3.115 1.417,3.396 0.219,0.281 18 true iii 5.354,0.677 5.573,0.958 0.219,0.281 18 true iii 6.656,0.635 6.875,0.917 0.219,0.281 18 true iii
V113147

Release in this Direction
V100135

Connector
V100136

Bolt A
V100137

Bolt B


i.

Using a thin-bladed screwdriver, release the lock as shown in the illustration and disconnect the pretensioner connector.

HINT:

Tape the thin-bladed screwdriver tip before use.



ii.

Remove the bolt A and bolt B.


iii.

Detach the guide and remove the rear seat outer belt assembly LH.



Hide 73360D 20.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH

a.
B600231C02
5.844,0.375 5.979,0.667 0.135,0.292 18 true i 5.083,2.635 5.219,2.927 0.135,0.292 18 true i 5.104,0.969 5.292,1.26 0.188,0.292 18 true ii 6.188,0.813 6.375,1.104 0.188,0.292 18 true ii 5.885,3.219 6.073,3.51 0.188,0.292 18 true ii 1.708,0.146 1.927,0.427 0.219,0.281 18 true iii
V113147

Release in this Direction
V100135

Connector
V100136

Bolt A
V100137

Bolt B


i.

Remove the bolt A and bolt B.


ii.

Detach the guide.


iii.

Using a thin-bladed screwdriver, release the lock as shown in the illustration to disconnect the pretensioner connector and remove the rear seat outer belt assembly RH.

NOTICE:

Do not pull while holding the wire harness.


HINT:

Tape the thin-bladed screwdriver tip before use.




Hide 73439 21.REMOVE REAR SEAT BELT RETRACTOR CUSHION LH

Z101186

HINT:

Perform this procedure when replacing the rear seat belt retractor cushion LH.



a.
B607701


Hide 73439 22.REMOVE REAR SEAT BELT RETRACTOR CUSHION RH

Z101186

HINT:

Perform this procedure when replacing the rear seat belt retractor cushion RH.



a.

Use the same procedure described for the LH side.