Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B002813  Right Side Airbag Deployment Control Circuit Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B002813 Right Side Airbag Deployment Control Circuit Open One of the following conditions is met:
·

The airbag ECU assembly detects an open circuit signal in the right side 1st seat side-airbag squib circuit for 2 seconds.

·

A front seat airbag assembly RH malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Front seat airbag assembly RH

·

Airbag ECU assembly


Comes on SRS Airbag A Applicable

WIRING DIAGRAM

C409207E95
5.354,1.698 5.688,1.885 0.333,0.188 10 false G64 5.375,0.323 5.583,0.49 0.208,0.167 10 false 9 5.604,0.406 6.01,0.604 0.406,0.198 10 false SFR+ 5.302,1.104 5.552,1.26 0.25,0.156 10 false 10 1.729,1.104 1.906,1.271 0.177,0.167 10 false 2 1.708,0.354 1.927,0.583 0.219,0.229 10 false 1 5.604,1.219 6.052,1.406 0.448,0.188 10 false SFR- 5.365,1.833 6.979,2.052 1.615,0.219 10 false Airbag ECU Assembly 0.177,1.698 0.823,1.875 0.646,0.177 10 false k1 0.177,1.844 2.219,2.25 2.042,0.406 10 false Front Seat Airbag Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B002813 is output A
History B002813 is output B


Post-procedure1

a.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the front seat airbag assembly RH and airbag ECU assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C400937C01
0.625,1.104 0.938,1.302 0.313,0.198 10 false *1 1.24,1.094 1.552,1.292 0.313,0.198 10 false *3 2.229,1.677 2.542,1.875 0.313,0.198 10 false *2
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the front seat airbag assembly RH connector.


Procedure1

a.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



b.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CHECK FRONT SEAT AIRBAG ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT SEAT AIRBAG ASSEMBLY RH
a.
E441543C07
0.458,2.25 0.833,2.5 0.375,0.25 1.76,2.344 1.938,2.448 1.938,2.448 2.083,2.448 true 0.604,1.177 1.094,1.583 0.49,0.406 10 false *1 2.26,1.323 2.74,1.74 0.479,0.417 10 false *2 1.823,0.938 2.208,1.458 0.385,0.521 10 false A 1.677,0.938 2.167,1.417 0.49,0.479 10 false B 1.167,0.948 1.917,1.448 0.75,0.5 10 false C 0.823,0.948 1.604,1.344 0.781,0.396 10 false D 2.135,2.365 2.573,2.698 0.438,0.333 10 false *4 0.302,1.896 0.698,2.26 0.396,0.365 10 false *a 0.583,2.302 1.031,2.771 0.448,0.469 10 false k1 1.427,1.167 1.865,1.5 0.438,0.333 10 false *3
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 SST
*a Front view of wire harness connector
(to Front Seat Airbag Assembly RH)


Connect the connector to the airbag ECU assembly.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK FRONT SEAT AIRBAG ASSEMBLY RH
5.CHECK FRONT SEAT AIRBAG ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B002813 is not output A
B002813 is output B


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Disconnect SST from connector C.



A

B

6.CHECK HARNESS AND CONNECTOR
6.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
E441544C11
0.583,2.167 1,2.417 0.417,0.25 0.563,1.188 0.875,1.344 0.313,0.156 10 false *1 2.25,1.292 2.563,1.448 0.313,0.156 10 false *2 1.219,1.156 1.531,1.313 0.313,0.156 10 false *3 0.302,1.844 0.615,2.063 0.313,0.219 10 false *a 0.729,2.219 1.104,2.438 0.375,0.219 10 false k1 1.833,0.958 2.031,1.146 0.198,0.188 10 false A 1.521,0.969 1.719,1.177 0.198,0.208 10 false B 1.021,0.969 1.219,1.146 0.198,0.177 10 false C 0.688,0.969 0.844,1.146 0.156,0.177 10 false D
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Front Seat Airbag Assembly RH)


Disconnect the G64 airbag ECU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(k1)Location & Routing

Click Connector(k1)Seat>Front Seat Airbag Assembly LH / Front Seat Airbag Assembly RH>Front Seat Airbag Assembly RH

k1-1 - k1-2 Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.
C238241C38
0.771,1.521 1.083,1.719 0.313,0.198 10 false *1 2.167,1.615 2.479,1.813 0.313,0.198 10 false *2 1.323,1.51 1.635,1.708 0.313,0.198 10 false *3
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the front seat airbag assembly RH connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B002813 is not output A
B002813 is output B


Post-procedure1

a.

None



A

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




B