Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009283  Left Side Restraints Sensor 2 Value of Signal Protection Calculation Incorrect  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009283 Left Side Restraints Sensor 2 Value of Signal Protection Calculation Incorrect One of the following conditions is met:
·

A side airbag sensor assembly LH malfunction.

·

An airbag ECU assembly malfunction.


·

Side airbag sensor assembly LH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C370759E97
5.427,2.958 7.031,3.188 1.604,0.229 10 false Airbag ECU Assembly 5.417,2.771 6.531,3.198 1.115,0.427 10 false G43 5.625,0.865 6.74,1.292 1.115,0.427 10 false BCL+ 5.333,0.781 6.448,1.208 1.115,0.427 10 false 28 5.615,2.063 6.729,2.49 1.115,0.427 10 false BCL- 5.313,1.958 6.427,2.385 1.115,0.427 10 false 29 1.25,0.917 2.365,1.344 1.115,0.427 10 false BFL+ 1.24,2.083 2.354,2.51 1.115,0.427 10 false BFL- 1.729,0.75 2.844,1.177 1.115,0.427 10 false 2 1.719,1.969 2.833,2.396 1.115,0.427 10 false 1 0.052,2.781 0.5,2.958 0.448,0.177 10 false G35 0.063,2.958 2.865,3.344 2.802,0.385 10 false Side Airbag Sensor Assembly LH

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B009283 is output A
B009283 is not output B


Post-procedure1

a.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the airbag ECU assembly and No. 2 side airbag sensor assembly LH.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

CONNECT CONNECTORS PROPERLY

3.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C400939C03
0.917,1.063 1.229,1.219 0.313,0.156 10 false *1 2.417,1.406 2.729,1.563 0.313,0.156 10 false *2 1.604,0.802 1.917,0.958 0.313,0.156 10 false *3
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Interchange the side airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

4.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
4.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B009283 is output A
B009783 is output B


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B