Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009296  Left Side Restraints Sensor 2 Component Internal Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009296 Left Side Restraints Sensor 2 Component Internal Failure Either condition is met:
·

A side airbag sensor assembly LH malfunction.

·

An airbag ECU assembly malfunction.


·

Side airbag sensor assembly LH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C370759E97
5.427,2.958 7.031,3.188 1.604,0.229 10 false Airbag ECU Assembly 5.417,2.771 6.531,3.198 1.115,0.427 10 false G43 5.625,0.865 6.74,1.292 1.115,0.427 10 false BCL+ 5.333,0.781 6.448,1.208 1.115,0.427 10 false 28 5.615,2.063 6.729,2.49 1.115,0.427 10 false BCL- 5.313,1.958 6.427,2.385 1.115,0.427 10 false 29 1.25,0.917 2.365,1.344 1.115,0.427 10 false BFL+ 1.24,2.083 2.354,2.51 1.115,0.427 10 false BFL- 1.729,0.75 2.844,1.177 1.115,0.427 10 false 2 1.719,1.969 2.833,2.396 1.115,0.427 10 false 1 0.052,2.781 0.5,2.958 0.448,0.177 10 false G35 0.063,2.958 2.865,3.344 2.802,0.385 10 false Side Airbag Sensor Assembly LH

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C400939C03
0.917,1.063 1.229,1.219 0.313,0.156 10 false *1 2.417,1.406 2.729,1.563 0.313,0.156 10 false *2 1.604,0.802 1.917,0.958 0.313,0.156 10 false *3
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

2.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
2.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B009284 is output A
B009784 is output B
B009284 and B009784 are not output C


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C