Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009784  Right Side Restraints Sensor 2 Signal Below Allowable Range  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009784 Right Side Restraints Sensor 2 Signal Below Allowable Range Either condition is met:
·

A side airbag sensor assembly RH malfunction.

·

An airbag ECU assembly malfunction.


·

Side airbag sensor assembly RH

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C370759E99
5.51,2.927 7.115,3.156 1.604,0.229 10 false Airbag ECU Assembly 5.5,2.76 5.958,2.927 0.458,0.167 10 false G64 5.292,0.792 5.75,1.094 0.458,0.302 10 false 28 5.302,1.99 6.052,2.365 0.75,0.375 10 false 29 5.615,0.875 6.073,1.177 0.458,0.302 10 false BCR+ 5.604,2.063 6.354,2.438 0.75,0.375 10 false BCR- 1.729,0.802 2.188,1.104 0.458,0.302 10 false 2 1.729,1.948 2.188,2.25 0.458,0.302 10 false 1 1.229,0.906 1.729,1.208 0.5,0.302 10 false BFR+ 1.198,2.094 1.948,2.469 0.75,0.375 10 false BFR- 0.073,2.781 0.604,2.958 0.531,0.177 10 false G34 0.073,2.958 2.625,3.167 2.552,0.208 10 false Side Airbag Sensor Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C374693C27
0.979,1.552 1.292,1.708 0.313,0.156 10 false *1 2.458,1.417 2.771,1.573 0.313,0.156 10 false *2 1.646,1.354 1.958,1.51 0.313,0.156 10 false *3
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

2.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
2.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B009784 is output A
B009284 is output B
B009284 and B009784 are not output C


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors to them.



A

B

C