| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B009787 | Right Side Restraints Sensor 2 Missing Message | One of the following conditions is met:
·
The airbag ECU assembly detects a line short in the side collision sensor RH circuit (bus 2) for 2 seconds. ·
The airbag ECU assembly detects a short to ground in the side collision sensor RH circuit (bus 2) for 2 seconds. ·
The airbag ECU assembly detects a short to B+ in the side collision sensor RH circuit (bus 2) for 2 seconds. ·
The airbag ECU assembly detects an open in the side collision sensor RH circuit (bus 2) for 2 seconds. ·
A side airbag sensor assembly RH malfunction. ·
An airbag ECU assembly malfunction. |
·
Wire harness ·
Side airbag sensor assembly RH ·
Airbag ECU assembly |
Comes on | SRS Airbag | A | Not applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the airbag ECU assembly and side airbag sensor RH.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the side airbag sensor assembly RH connector.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G34)Location & Routingewd_type=routing;type=c;code=G34 Click Connector(G34)Seat>Floor Wire>Side Airbag Sensor Assembly RHewd_type=component;type=c;code=G34;pinno=2,1 |
||
| G34-2 (BFR+) - G34-1 (BFR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Using a service wire, connect terminals 28 (BCR+) and 29 (BCR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G34)Location & Routingewd_type=routing;type=c;code=G34 Click Connector(G34)Seat>Floor Wire>Side Airbag Sensor Assembly RHewd_type=component;type=c;code=G34;pinno=2,1 |
||
| G34-2 (BFR+) - G34-1 (BFR-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Disconnect the service wire from connector B.
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G34)Location & Routingewd_type=routing;type=c;code=G34 Click Connector(G34)Seat>Floor Wire>Side Airbag Sensor Assembly RHewd_type=component;type=c;code=G34;pinno=2,1 |
||
| G34-2 (BFR+) - Body ground | Always | 1 MΩ or higher |
| G34-1 (BFR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G34)Location & Routingewd_type=routing;type=c;code=G34 Click Connector(G34)Seat>Floor Wire>Side Airbag Sensor Assembly RHewd_type=component;type=c;code=G34;pinno=2,1 |
||
| G34-2 (BFR+) - Body ground | Ignition switch ON | Below 1 V |
| G34-1 (BFR-) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
OK
NG
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Connect the connector to the airbag ECU assembly.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B009787 is output | A |
| B009287 is not output | B |
| B009287 and B009787 are not output | C |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING