Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009B87  Left Side Restraints Sensor 5 Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009B87 Left Side Restraints Sensor 5 Missing Message One of the following conditions is met:
·

A side airbag pressure sensor LH malfunction.

·

Airbag ECU assembly malfunction.


·

Wire harness

·

Side airbag pressure sensor LH

·

Door side airbag sensor LH

·

Airbag ECU assembly


Comes on SRS Airbag B Not applicable

WIRING DIAGRAM

C450171E02
1.594,0.677 1.75,0.875 0.156,0.198 10 false 2 1.583,1.479 1.74,1.677 0.156,0.198 10 false 1 2.854,0.656 3.01,0.854 0.156,0.198 10 false 1 2.844,1.479 3,1.677 0.156,0.198 10 false 2 4.146,0.667 4.302,0.865 0.156,0.198 10 false 4 5.333,0.656 5.646,0.854 0.313,0.198 10 false 32 5.365,1.49 5.677,1.688 0.313,0.198 10 false 31 4.177,1.49 4.333,1.688 0.156,0.198 10 false 3 5.635,0.813 6.25,1.01 0.615,0.198 10 false BBL+ 5.635,1.573 6.25,1.771 0.615,0.198 10 false BBL- 0.094,2.219 0.406,2.417 0.313,0.198 10 false E23 0.094,2.365 2.229,2.583 2.135,0.219 10 false Side Airbag Pressure Sensor LH 2.896,2.208 3.208,2.406 0.313,0.198 10 false G63 2.906,2.365 4.354,2.563 1.448,0.198 10 false Rear Airbag Sensor LH 5.51,2.24 6.125,2.438 0.615,0.198 10 false G43 5.521,2.406 6.948,2.635 1.427,0.229 10 false Airbag ECU Assembly 3.073,0.781 3.688,0.979 0.615,0.198 10 false BDL+ 3.083,1.573 3.698,1.771 0.615,0.198 10 false BDL- 3.708,0.781 4.323,0.979 0.615,0.198 10 false BCL+ 3.708,1.583 4.323,1.781 0.615,0.198 10 false BCL- 1.094,0.781 1.708,0.979 0.615,0.198 10 false BDL+ 1.083,1.604 1.698,1.802 0.615,0.198 10 false BDL-

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B009387 and B009B87 are output A
B009B87 is output B
B009387 and B009B87 are not output C


Post-procedure1

a.

None



A

B

2.CHECK CONNECTION OF CONNECTORS

C

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the side airbag pressure sensor LH and rear airbag sensor LH.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E441555C03
0.719,0.865 1.135,1.115 0.417,0.25 0.823,3.448 1.24,3.698 0.417,0.25 1.24,3 1.49,3 1.49,3 1.698,3.51 true 2.354,3.01 2.104,3.01 2.104,3.01 1.938,3.49 true 1.302,1.583 1.552,1.583 1.552,1.583 1.719,1.094 true 2.354,1.583 2.104,1.583 2.104,1.583 1.885,1.073 true 1.135,4.167 1.552,4.167 true 0.385,2.594 0.698,2.75 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.521,2.313 1.833,2.469 0.313,0.156 10 false *3 0.74,0.292 1.052,0.448 0.313,0.156 10 false *a 0.469,2.854 0.781,3.01 0.313,0.156 10 false *b 0.927,3.5 1.24,3.656 0.313,0.156 10 false E23 2.406,2.115 2.719,2.271 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.031,2.125 1.344,2.281 0.313,0.156 10 false C 0.719,2.125 1.031,2.281 0.313,0.156 10 false D 0.813,0.917 1.125,1.073 0.313,0.156 10 false G63 0.958,1.51 1.521,1.771 0.563,0.26 10 false BDL+ 2.417,1.5 2.979,1.76 0.563,0.26 10 false BDL- 2.406,2.927 2.969,3.188 0.563,0.26 10 false BDL+ 0.875,2.938 1.438,3.198 0.563,0.26 10 false BDL- 0.927,4.104 1.24,4.26 0.313,0.156 10 false *4
*1 Rear Airbag Sensor LH
*2 Side Airbag Pressure Sensor LH
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Disconnect the G63 rear airbag sensor LH connector.


b.

Disconnect the E23 side airbag pressure sensor LH connector.


c.

Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G63)Location & Routing

Click Connector(G63)Body>Floor Wire / No. 3 Floor Wire>Rear Airbag Sensor LH

G63-1 (BDL+) - G63-2 (BDL-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the service wire from connector B.



OK

4.CHECK SIDE AIRBAG PRESSURE SENSOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SIDE AIRBAG PRESSURE SENSOR LH
a.
B529883C12
0.969,1.521 1.24,1.719 0.271,0.198 10 false *1 2.323,1.531 2.594,1.729 0.271,0.198 10 false *2 1.646,1.271 1.917,1.469 0.271,0.198 10 false *3
*1 Side Airbag Pressure Sensor RH
*2 Rear Airbag Sensor LH
*3 Wire Harness


Connect the G63 rear airbag sensor LH connector.


b.

Interchange the side airbag pressure sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK SIDE AIRBAG PRESSURE SENSOR LH
5.CHECK SIDE AIRBAG PRESSURE SENSOR LH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B009B87 is output A
B009E87 is output B


HINT:

Codes other than DTCs B009B87 and B009E87 may be output at this time, but they are not related to this check.


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG PRESSURE SENSOR LH