Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009E87  Right Side Restraints Sensor 5 Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009E87 Right Side Restraints Sensor 5 Missing Message One of the following conditions is met:
·

A side airbag pressure sensor RH malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Side airbag pressure sensor RH

·

Airbag ECU assembly


Comes on SRS Airbag B Not applicable

WIRING DIAGRAM

C450171E03
1.594,0.677 1.75,0.875 0.156,0.198 10 false 2 1.583,1.479 1.74,1.677 0.156,0.198 10 false 1 2.854,0.656 3.01,0.854 0.156,0.198 10 false 1 2.844,1.479 3,1.677 0.156,0.198 10 false 2 4.146,0.667 4.302,0.865 0.156,0.198 10 false 4 5.333,0.656 5.646,0.854 0.313,0.198 10 false 26 5.365,1.479 5.677,1.677 0.313,0.198 10 false 25 4.177,1.49 4.333,1.688 0.156,0.198 10 false 3 5.635,0.792 6.25,0.99 0.615,0.198 10 false BBR+ 5.635,1.573 6.25,1.771 0.615,0.198 10 false BBR- 0.094,2.219 0.406,2.417 0.313,0.198 10 false E5 0.094,2.365 2.229,2.583 2.135,0.219 10 false Side Airbag Pressure Sensor RH 2.896,2.208 3.208,2.406 0.313,0.198 10 false G40 2.906,2.365 4.354,2.563 1.448,0.198 10 false Rear Airbag Sensor RH 5.51,2.24 6.125,2.438 0.615,0.198 10 false G64 5.521,2.406 6.948,2.635 1.427,0.229 10 false Airbag ECU Assembly 3.073,0.781 3.688,0.979 0.615,0.198 10 false BDR+ 3.083,1.573 3.698,1.771 0.615,0.198 10 false BDR- 3.615,0.781 4.229,0.979 0.615,0.198 10 false BCR+ 3.646,1.583 4.26,1.781 0.615,0.198 10 false BCR- 1.094,0.781 1.708,0.979 0.615,0.198 10 false BDR+ 1.083,1.604 1.698,1.802 0.615,0.198 10 false BDR-

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B009887 and B009E87 are output A
B009E87 is output B
B009887 and B009E87 are not output C


Post-procedure1

a.

None



A

B

2.CHECK CONNECTION OF CONNECTORS

C

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the side airbag pressure sensor RH and rear airbag sensor RH.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E441555C04
0.719,0.865 1.135,1.115 0.417,0.25 0.823,3.448 1.24,3.698 0.417,0.25 1.24,3 1.49,3 1.49,3 1.698,3.51 true 2.354,3.01 2.104,3.01 2.104,3.01 1.938,3.49 true 1.302,1.583 1.552,1.583 1.552,1.583 1.719,1.094 true 2.354,1.583 2.104,1.583 2.104,1.583 1.885,1.073 true 1.135,4.167 1.552,4.167 true 0.385,2.594 0.698,2.75 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.521,2.313 1.833,2.469 0.313,0.156 10 false *3 0.74,0.292 1.052,0.448 0.313,0.156 10 false *a 0.469,2.854 0.781,3.01 0.313,0.156 10 false *b 0.979,3.5 1.292,3.656 0.313,0.156 10 false E5 2.406,2.115 2.719,2.271 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.031,2.125 1.344,2.281 0.313,0.156 10 false C 0.719,2.125 1.031,2.281 0.313,0.156 10 false D 0.833,0.917 1.146,1.073 0.313,0.156 10 false G40 0.896,1.51 1.458,1.771 0.563,0.26 10 false BDR+ 2.417,1.5 2.979,1.76 0.563,0.26 10 false BDR- 2.406,2.927 2.969,3.188 0.563,0.26 10 false BDR+ 0.875,2.938 1.438,3.198 0.563,0.26 10 false BDR- 0.927,4.104 1.24,4.26 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor RH
*2 Rear Airbag Sensor RH
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)


Disconnect the G40 rear airbag sensor RH connector.


b.

Disconnect the E5 side airbag pressure sensor RH connector.


c.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G40)Location & Routing

Click Connector(G40)Body>Floor Wire / No. 3 Floor Wire>Rear Airbag Sensor RH

G40-1 (BDR+) - G40-2 (BDR-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the service wire from connector B.



OK

4.CHECK SIDE AIRBAG PRESSURE SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SIDE AIRBAG PRESSURE SENSOR RH
a.
B529883C12
0.969,1.521 1.24,1.719 0.271,0.198 10 false *1 2.323,1.531 2.594,1.729 0.271,0.198 10 false *2 1.646,1.271 1.917,1.469 0.271,0.198 10 false *3
*1 Side Airbag Pressure Sensor LH
*2 Rear Airbag Sensor RH
*3 Wire Harness


Connect the G40 rear airbag sensor RH connector.


b.

Interchange the side airbag pressure sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK SIDE AIRBAG PRESSURE SENSOR RH
5.CHECK SIDE AIRBAG PRESSURE SENSOR RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B009E87 is output A
B009B87 is output B


HINT:

Codes other than DTCs B009B87 and B009E87 may be output at this time, but they are not related to this check.


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG PRESSURE SENSOR RH