Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00DF13  Passenger Restraints Disable Switch Circuit Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B00DF13 Passenger Restraints Disable Switch Circuit Open One of the following conditions is met:
·

The airbag ECU assembly detects an open circuit signal in the airbag cutoff switch cylinder sub-assembly circuit for 2 seconds.

·

An airbag cutoff switch cylinder sub-assembly malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Airbag cutoff switch cylinder sub-assembly

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C262371E29
2.094,1.063 2.573,1.26 0.479,0.198 10 false PMC+ 2.125,2.24 2.604,2.438 0.479,0.198 10 false PMC- 5.469,3.063 5.813,3.26 0.344,0.198 10 false D10 0.188,3.198 3.01,3.406 2.823,0.208 10 false Airbag Cutoff Switch Cylinder Sub-assembly 2.573,1.073 2.813,1.281 0.24,0.208 10 false 2 2.573,2.24 2.813,2.448 0.24,0.208 10 false 1 5.51,1.063 5.76,1.271 0.25,0.208 10 false 22 5.542,2.24 5.802,2.448 0.26,0.208 10 false 21 5.771,1.146 6.302,1.344 0.531,0.198 10 false MSW+ 5.771,2.344 6.302,2.542 0.531,0.198 10 false MSW- 0.167,3.042 0.531,3.229 0.365,0.188 10 false D47 5.469,3.208 7.052,3.698 1.583,0.49 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, shake each connector of the airbag system or drive the vehicle on various types of road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the airbag ECU assembly and airbag cutoff switch cylinder sub-assembly.


Result:
Result Proceed to
The connectors are properly connected A
The connectors are not properly connected B


Post-procedure1

a.

None



A

2.CHECK CONNECTORS

B

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
C215710C06
0.625,1.427 0.938,1.583 0.313,0.156 10 *1 2.531,1.563 2.844,1.719 0.313,0.156 10 *2 1.49,1.104 1.802,1.26 0.313,0.156 10 *3
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the airbag cutoff switch cylinder sub-assembly connector.


Procedure1

a.

Check that the connectors (on the airbag ECU assembly side and airbag cutoff switch cylinder sub-assembly side) are not damaged.


Result:
Result Proceed to
The connectors are not deformed or damaged A
The connectors are deformed or damaged B


Post-procedure1

a.

None



A

3.INSPECT AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR

NG

4.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
C412276C06
2.417,3.688 2.865,3.938 0.448,0.25 0.531,0.583 0.979,0.833 0.448,0.25 0.969,3.698 1.167,3.698 1.167,3.698 1.594,3.979 true 1.073,3.375 1.271,3.375 1.271,3.375 1.677,3.969 true 0.917,1.375 1.115,1.375 1.115,1.375 1.385,1.156 true 1.688,1.156 1.979,1.323 1.979,1.323 2.188,1.323 true 1.76,4.344 1.854,4.469 1.854,4.469 2.063,4.469 true 0.438,2.594 0.75,2.75 0.313,0.156 10 false *1 2.813,2.698 3.125,2.854 0.313,0.156 10 false *2 1.51,1.927 1.823,2.083 0.313,0.156 10 false *3 2.115,4.406 2.427,4.563 0.313,0.156 10 false *4 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 0.531,3.125 0.844,3.281 0.313,0.156 10 false *b 0.594,3.292 1.104,3.573 0.51,0.281 10 false MSW+ 0.552,3.604 1.063,3.885 0.51,0.281 10 false MSW- 2.51,3.729 3.021,4.01 0.51,0.281 10 false D10 2.26,1.198 2.771,1.479 0.51,0.281 10 false PMC+ 0.5,1.25 1.01,1.531 0.51,0.281 10 false PMC- 0.604,0.635 1.115,0.917 0.51,0.281 10 false D47 0.698,2.104 0.896,2.313 0.198,0.208 10 false D 1.01,2.104 1.208,2.313 0.198,0.208 10 false C 2.385,2.115 2.583,2.323 0.198,0.208 10 false A 2.063,2.115 2.26,2.323 0.198,0.208 10 false B
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Cutoff Switch Cylinder Sub-assembly)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Using a service wire, connect terminals 22 (MSW+) and 21 (MSW-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D47)Location & Routing

Click Connector(D47)Instrument Panel>Instrument Panel Wire>Airbag Cut Off Switch Cylinder Sub-Assembly

D47-2 (PMC+) - D47-1 (PMC-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the service wire from connector B.



OK

5.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CLEAR DTC
a.
C391328C04
1.01,1.26 1.323,1.458 0.313,0.198 10 false *1 1.823,1.375 2.135,1.573 0.313,0.198 10 false *2 1.427,0.99 1.74,1.188 0.313,0.198 10 false *3
*1 Airbag Cutoff Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the airbag cutoff switch cylinder sub-assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B00DF13 is output A
B00DF13 is not output B


Post-procedure1

a.

None



A

B