Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › PEDESTRIAN PROTECTION SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0454682 PEDESTRIAN PROTECTION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  PEDESTRIAN PROTECTION SYSTEM  B16A200  RH Sensor for Pedestrian Protection System Signal Plausibility Failure (Detection for Sensor)  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B16A200 RH Sensor for Pedestrian Protection System Signal Plausibility Failure (Detection for Sensor) Either condition is met:
·

A pedestrian detection chamber assembly (pedestrian protection sensor) malfunction

·

An airbag ECU assembly malfunction


·

Pedestrian detection chamber assembly (pedestrian protection sensor)

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C370759E88
1.167,0.896 1.604,1.052 0.438,0.156 10 false PSR+ 1.208,2.104 1.604,2.271 0.396,0.167 10 false PSR- 1.708,1.958 2.063,2.115 0.354,0.156 10 false 2 1.708,0.781 2.063,0.938 0.354,0.156 10 false 1 0.135,2.823 0.49,2.979 0.354,0.156 10 false A24 0.146,2.979 2.688,3.333 2.542,0.354 10 false Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor) 5.271,0.771 5.49,0.958 0.219,0.188 10 false 21 5.292,1.958 5.521,2.135 0.229,0.177 10 false 22 5.5,2.813 5.854,2.969 0.354,0.156 10 false G64 5.51,2.979 7.104,3.469 1.594,0.49 10 false Airbag ECU Assembly 5.646,0.885 6.156,1.042 0.51,0.156 10 false PSR+ 5.646,2.083 6.115,2.26 0.469,0.177 10 false PSR-

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.REPLACE PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Replace the pedestrian detection chamber assembly (pedestrian protection sensor) with a new one.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>POP UP HOOD SENSOR>REMOVAL



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B16A200 is output A
B16A200 is not output B


Post-procedure1

a.

None



A

B

END (PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR) WAS DEFECTIVE)