Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › PEDESTRIAN PROTECTION SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0454682 PEDESTRIAN PROTECTION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  PEDESTRIAN PROTECTION SYSTEM  B16A287  RH Sensor for Pedestrian Protection System Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B16A287 RH Sensor for Pedestrian Protection System Missing Message One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the pedestrian detection chamber assembly (pedestrian protection sensor) for 2 seconds

·

A pedestrian detection chamber assembly (pedestrian protection sensor) malfunction

·

An airbag ECU assembly malfunction


·

Pedestrian detection chamber assembly (pedestrian protection sensor)

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C370759E88
1.167,0.896 1.604,1.052 0.438,0.156 10 false PSR+ 1.208,2.104 1.604,2.271 0.396,0.167 10 false PSR- 1.708,1.958 2.063,2.115 0.354,0.156 10 false 2 1.708,0.781 2.063,0.938 0.354,0.156 10 false 1 0.135,2.823 0.49,2.979 0.354,0.156 10 false A24 0.146,2.979 2.688,3.333 2.542,0.354 10 false Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor) 5.271,0.771 5.49,0.958 0.219,0.188 10 false 21 5.292,1.958 5.521,2.135 0.229,0.177 10 false 22 5.5,2.813 5.854,2.969 0.354,0.156 10 false G64 5.51,2.979 7.104,3.469 1.594,0.49 10 false Airbag ECU Assembly 5.646,0.885 6.156,1.042 0.51,0.156 10 false PSR+ 5.646,2.083 6.115,2.26 0.469,0.177 10 false PSR-

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the airbag ECU assembly and pedestrian detection chamber assembly (pedestrian protection sensor).

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

2.CHECK CONNECTOR

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTOR

Pre-procedure1

a.
C208245C43
0.646,1.75 0.958,1.948 0.313,0.198 10 false *1 2.573,1.542 2.885,1.74 0.313,0.198 10 false *2 1.51,0.958 1.823,1.156 0.313,0.198 10 false *3
*1 Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the pedestrian detection chamber assembly (pedestrian protection sensor) connector.


Procedure1

a.

Check that the connectors (on the airbag ECU assembly side and pedestrian detection chamber assembly (pedestrian protection sensor) side) are not damaged.

OK:

The connectors are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)
a.
E441551C05
1.26,3.667 1.677,3.917 0.417,0.25 0.375,0.844 0.792,1.094 0.417,0.25 1.917,4.448 2.167,4.448 2.167,4.448 2.313,3.927 true 2.75,4.448 2.5,4.448 2.5,4.448 2.406,3.948 true 0.854,1.469 1.104,1.469 1.104,1.469 1.24,0.979 true 1.938,1.469 1.688,1.469 1.688,1.469 1.458,0.979 true 0.385,2.896 0.573,3.063 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.01,2.417 1.198,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.396,2.406 2.583,2.573 0.188,0.167 10 false A 2.844,2.698 3.031,2.865 0.188,0.167 10 false *2 0.469,0.896 0.771,1.052 0.302,0.156 10 false A24 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.51,1.396 1.021,1.573 0.51,0.177 10 false PSR+ 1.99,1.385 2.469,1.552 0.479,0.167 10 false PSR- 1.552,4.375 1.979,4.573 0.427,0.198 10 false PSR+ 2.781,4.375 3.167,4.531 0.385,0.156 10 false PSR- 1.354,3.719 1.677,3.896 0.323,0.177 10 false G64 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.594 1.719,2.75 0.229,0.156 10 false *3
*1 Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor))
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A24)Location & Routing

Click Connector(A24)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Pedestrian Detection Chamber Assembly RH

A24-1 (PSR+) - A24-2 (PSR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

a.
E449137C02
1.26,3.667 1.677,3.917 0.417,0.25 0.375,0.844 0.792,1.094 0.417,0.25 1.594,4.344 1.844,4.344 1.844,4.344 2.323,3.875 true 2.823,3.177 2.573,3.177 2.573,3.177 2.417,3.865 true 0.854,1.469 1.104,1.469 1.104,1.469 1.24,0.979 true 1.938,1.469 1.688,1.469 1.688,1.469 1.458,0.979 true 2.948,4.479 2.698,4.479 2.698,4.479 2.51,4.354 true 0.385,2.896 0.573,3.063 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.01,2.417 1.198,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.396,2.406 2.583,2.573 0.188,0.167 10 false A 2.781,2.719 2.969,2.885 0.188,0.167 10 false *2 0.469,0.896 0.771,1.052 0.302,0.156 10 false A24 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.51,1.396 1.021,1.573 0.51,0.177 10 false PSR+ 2.021,1.375 2.5,1.542 0.479,0.167 10 false PSR- 1.219,4.302 1.646,4.5 0.427,0.198 10 false PSR+ 2.854,3.115 3.24,3.271 0.385,0.156 10 false PSR- 1.354,3.719 1.677,3.896 0.323,0.177 10 false G64 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.458,2.615 1.688,2.771 0.229,0.156 10 false *3 2.979,4.385 3.229,4.552 0.25,0.167 10 false *4
*1 Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)
*2 Airbag ECU Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor))
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Using a service wire, connect terminals 21 (PSR+) and 22 (PSR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A24)Location & Routing

Click Connector(A24)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Pedestrian Detection Chamber Assembly RH

A24-1 (PSR+) - A24-2 (PSR-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the service wire from connector B.



OK

5.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)
a.
E441551C05
1.26,3.667 1.677,3.917 0.417,0.25 0.375,0.844 0.792,1.094 0.417,0.25 1.917,4.448 2.167,4.448 2.167,4.448 2.313,3.927 true 2.75,4.448 2.5,4.448 2.5,4.448 2.406,3.948 true 0.854,1.469 1.104,1.469 1.104,1.469 1.24,0.979 true 1.938,1.469 1.688,1.469 1.688,1.469 1.458,0.979 true 0.385,2.896 0.573,3.063 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.01,2.417 1.198,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.396,2.406 2.583,2.573 0.188,0.167 10 false A 2.844,2.698 3.031,2.865 0.188,0.167 10 false *2 0.469,0.896 0.771,1.052 0.302,0.156 10 false A24 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.51,1.396 1.021,1.573 0.51,0.177 10 false PSR+ 1.99,1.385 2.469,1.552 0.479,0.167 10 false PSR- 1.552,4.375 1.979,4.573 0.427,0.198 10 false PSR+ 2.781,4.375 3.167,4.531 0.385,0.156 10 false PSR- 1.354,3.719 1.677,3.896 0.323,0.177 10 false G64 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.594 1.719,2.75 0.229,0.156 10 false *3
*1 Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor))
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A24)Location & Routing

Click Connector(A24)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Pedestrian Detection Chamber Assembly RH

A24-1 (PSR+) - Body ground Always 1 MΩ or higher
A24-2 (PSR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

6.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

a.
E441551C05
1.26,3.667 1.677,3.917 0.417,0.25 0.375,0.844 0.792,1.094 0.417,0.25 1.917,4.448 2.167,4.448 2.167,4.448 2.313,3.927 true 2.75,4.448 2.5,4.448 2.5,4.448 2.406,3.948 true 0.854,1.469 1.104,1.469 1.104,1.469 1.24,0.979 true 1.938,1.469 1.688,1.469 1.688,1.469 1.458,0.979 true 0.385,2.896 0.573,3.063 0.188,0.167 10 false *1 0.708,2.417 0.896,2.583 0.188,0.167 10 false D 1.01,2.417 1.198,2.583 0.188,0.167 10 false C 2.063,2.417 2.25,2.583 0.188,0.167 10 false B 2.396,2.406 2.583,2.573 0.188,0.167 10 false A 2.844,2.698 3.031,2.865 0.188,0.167 10 false *2 0.469,0.896 0.771,1.052 0.302,0.156 10 false A24 0.25,0.25 0.438,0.417 0.188,0.167 10 false *a 0.51,1.396 1.021,1.573 0.51,0.177 10 false PSR+ 1.99,1.385 2.469,1.552 0.479,0.167 10 false PSR- 1.552,4.375 1.979,4.573 0.427,0.198 10 false PSR+ 2.781,4.375 3.167,4.531 0.385,0.156 10 false PSR- 1.354,3.719 1.677,3.896 0.323,0.177 10 false G64 1.167,3.146 1.354,3.313 0.188,0.167 10 false *b 1.49,2.594 1.719,2.75 0.229,0.156 10 false *3
*1 Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor))
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A24)Location & Routing

Click Connector(A24)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Pedestrian Detection Chamber Assembly RH

A24-1 (PSR+) - Body ground Ignition switch ON Below 1 V
A24-2 (PSR-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.



OK

7.REPLACE PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

7.REPLACE PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR)
a.

Replace the pedestrian detection chamber assembly (pedestrian protection sensor) with a new one.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>POP UP HOOD SENSOR>REMOVAL



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.
C374693C33
0.979,1.531 1.292,1.729 0.313,0.198 10 false *1 2.458,1.375 2.771,1.573 0.313,0.198 10 false *2 1.677,0.958 1.99,1.156 0.313,0.198 10 false *3
*1 Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the G64 airbag ECU assembly connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

9.CHECK DTC
9.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B16A287 is output A
B16A287 is not output B


Post-procedure1

a.

None



A

B

END (PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR) IS DEFECTIVE)