| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B16A783 | LH Sensor for Pedestrian Protection System Value of Signal Protection Calculation Incorrect | One of the following conditions is met:
·
The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the pedestrian detection chamber assembly (pedestrian protection sensor) for 2 seconds ·
A pedestrian detection chamber assembly (pedestrian protection sensor) malfunction ·
An airbag ECU assembly malfunction |
·
Pedestrian detection chamber assembly (pedestrian protection sensor) ·
Airbag ECU assembly |
Comes on | SRS Airbag | A | Not applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the airbag ECU assembly and pedestrian detection chamber assembly (pedestrian protection sensor).
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the pedestrian detection chamber assembly (pedestrian protection sensor) connector.
Procedure1
Check that the connectors (on the airbag ECU assembly side and pedestrian detection chamber assembly (pedestrian protection sensor) side) are not damaged.
The connectors are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A23)Location & Routingewd_type=routing;type=c;code=A23 |
||
| A23-1 (PSL+) - A23-2 (PSL-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Using a service wire, connect terminals 20 (PSL+) and 19 (PSL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A23)Location & Routingewd_type=routing;type=c;code=A23 |
||
| A23-1 (PSL+) - A23-2 (PSL-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Disconnect the service wire from connector B.
OK
NG
| *1 | Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A23)Location & Routingewd_type=routing;type=c;code=A23 |
||
| A23-1 (PSL+) - Body ground | Always | 1 MΩ or higher |
| A23-2 (PSL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)) |
| *b | Front view of wire harness connector
(to Airbag ECU Assembly) |
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A23)Location & Routingewd_type=routing;type=c;code=A23 |
||
| A23-1 (PSL+) - Body ground | Ignition switch ON | Below 1 V |
| A23-2 (PSL-) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
OK
NG
Replace the pedestrian detection chamber assembly (pedestrian protection sensor) with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor) |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Connect the G43 airbag ECU assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B16A783 is output | A |
| B16A783 is not output | B |
Post-procedure1
None
A
B