Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › PEDESTRIAN PROTECTION SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0454682 PEDESTRIAN PROTECTION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  PEDESTRIAN PROTECTION SYSTEM  B198012  Right Side Pop-up Hood Squib Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B198012 Right Side Pop-up Hood Squib Circuit Short to Battery One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit to B+ signal in the pop up hood squib RH circuit for 0.5 seconds

·

A pop up hood lifter assembly RH malfunction

·

An airbag ECU assembly malfunction


·

Wire harness

·

Pop up hood lifter assembly RH

·

Airbag ECU assembly


Comes on SRS Airbag A Applicable

WIRING DIAGRAM

C409207E73
5.354,1.677 5.688,1.865 0.333,0.188 10 false G64 5.323,0.323 5.802,0.573 0.479,0.25 10 false 8 5.333,1.083 5.667,1.292 0.333,0.208 10 false 7 1.74,0.333 1.917,0.5 0.177,0.167 10 false 2 1.75,1.094 1.969,1.323 0.219,0.229 10 false 1 5.625,1.198 6.083,1.396 0.458,0.198 10 false PUR- 1.177,0.323 1.656,0.51 0.479,0.188 10 false PLR+ 5.354,1.823 6.885,2.135 1.531,0.313 10 false Airbag ECU Assembly 0.063,1.677 0.708,1.854 0.646,0.177 10 false A47 0.073,1.823 2.219,2.052 2.146,0.229 10 false Pop Up Hood Lifter Assembly RH 5.615,0.438 6.094,0.625 0.479,0.188 10 false PUR+ 1.198,1.104 1.656,1.302 0.458,0.198 10 false PLR-

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>PEDESTRIAN PROTECTION SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>PEDESTRIAN PROTECTION SYSTEM>DATA LIST / ACTIVE TEST).


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B198012 is output A
History B198012 is output B


Post-procedure1

a.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the pop up hood lifter assembly RH and airbag ECU assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
E449121C01
0.656,1.563 0.969,1.719 0.313,0.156 10 false *1 2.198,1.604 2.51,1.76 0.313,0.156 10 false *2 1.271,1.542 1.583,1.698 0.313,0.156 10 false *3
*1 Pop Up Hood Lifter Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the pop up hood lifter assembly RH connector.


Procedure1

a.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



b.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CHECK POP UP HOOD LIFTER ASSEMBLY RH

NG

REPAIR OR REPLACE WIRE HARNESS

4.CHECK POP UP HOOD LIFTER ASSEMBLY RH
a.
C395623C25
0.521,2.229 0.969,2.5 0.448,0.271 2.01,2.677 2.219,3.01 2.219,3.01 2.375,3.01 true 1.667,2.26 2.083,1.844 2.083,1.844 2.208,1.844 true 1.49,2.26 1.021,1.844 1.021,1.844 0.885,1.844 true 0.615,1.135 0.927,1.292 0.313,0.156 10 false *1 2.396,1.26 2.708,1.417 0.313,0.156 10 false *2 2.427,2.938 2.74,3.094 0.313,0.156 10 false *4 0.333,1.604 0.646,1.76 0.313,0.156 10 false *a 0.646,2.281 0.958,2.438 0.313,0.156 10 false A47 0.74,0.906 1.052,1.063 0.313,0.156 10 false D 1.104,0.896 1.417,1.052 0.313,0.156 10 false C 1.865,0.896 2.177,1.052 0.313,0.156 10 false B 2.021,0.896 2.333,1.052 0.313,0.156 10 false A 2.292,1.802 2.708,2 0.417,0.198 10 false PLR+ 0.563,1.792 1.01,1.969 0.448,0.177 10 false PLR- 1.427,1.073 1.74,1.229 0.313,0.156 10 false *3
*1 Pop Up Hood Lifter Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 SST
*a Front view of wire harness connector
(to Pop Up Hood Lifter Assembly RH)


Connect the G64 airbag ECU assembly connector.


b.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the pop up hood lifter assembly RH for measurement, as this may lead to a serious injury due to pop up hood lifter deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK POP UP HOOD LIFTER ASSEMBLY RH
5.CHECK POP UP HOOD LIFTER ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B198012 is not output A
B198012 is output B


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Disconnect SST from connector C.



A

REPLACE POP UP HOOD LIFTER ASSEMBLY RH

B

6.CHECK POP UP HOOD LIFTER ASSEMBLY RH CIRCUIT
6.CHECK POP UP HOOD LIFTER ASSEMBLY RH CIRCUIT

Pre-procedure1

a.
E449125C03
0.385,2.25 0.802,2.5 0.417,0.25 0.75,2.833 1,2.833 1,2.833 1.188,2.458 true 1.813,2.833 1.563,2.833 1.563,2.833 1.354,2.438 true 0.75,1.167 1.063,1.323 0.313,0.156 10 false *1 2.781,1.25 3.094,1.406 0.313,0.156 10 false *2 0.229,1.625 0.542,1.781 0.313,0.156 10 false *a 2.021,0.948 2.333,1.104 0.313,0.156 10 false B 2.385,0.948 2.698,1.104 0.313,0.156 10 false A 1.438,0.948 1.75,1.104 0.313,0.156 10 false C 0.906,0.948 1.219,1.104 0.313,0.156 10 false D 0.479,2.302 0.792,2.458 0.313,0.156 10 false A47 0.417,2.76 0.823,2.917 0.406,0.156 10 false PLR- 1.844,2.771 2.25,2.927 0.406,0.156 10 false PLR+ 1.698,1.146 2.01,1.302 0.313,0.156 10 false *3
*1 Pop Up Hood Lifter Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Pop Up Hood Lifter Assembly RH)


Disconnect the G64 airbag ECU assembly connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A47)Location & Routing

Click Connector(A47)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Pop Up Hood Lifter Assembly RH

A47-2 (PLR+) - Body ground Ignition switch ON Below 1 V
A47-1 (PLR-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the igniton switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE WIRE HARNESS

7.CLEAR DTC
a.
C238241C37
0.688,1.073 1,1.229 0.313,0.156 10 false *1 2.438,1.604 2.75,1.76 0.313,0.156 10 false *2 1.302,1.104 1.615,1.26 0.313,0.156 10 false *3
*1 Pop Up Hood Lifter Assembly RH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the pop up hood lifter assembly RH connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B198012 is not output A
B198012 is output B


Post-procedure1

a.

None



A

USE SIMULATION METHOD TO CHECK

B