Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › PEDESTRIAN PROTECTION SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0454682 PEDESTRIAN PROTECTION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  PEDESTRIAN PROTECTION SYSTEM  B198511  Left Side Pop-up Hood Squib Circuit Short to Ground  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B198511 Left Side Pop-up Hood Squib Circuit Short to Ground One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit to ground signal in the pop up hood squib LH circuit for 0.5 seconds

·

A pop up hood lifter assembly LH malfunction

·

An airbag ECU assembly malfunction


·

Wire harness

·

Pop up hood lifter assembly LH

·

Airbag ECU assembly


Comes on SRS Airbag A Applicable

WIRING DIAGRAM

C409207E74
5.354,1.677 5.688,1.865 0.333,0.188 10 false G43 5.323,0.323 5.802,0.573 0.479,0.25 10 false 1 5.333,1.083 5.667,1.292 0.333,0.208 10 false 2 1.74,0.333 1.917,0.5 0.177,0.167 10 false 2 1.75,1.094 1.969,1.323 0.219,0.229 10 false 1 5.625,1.198 6.083,1.396 0.458,0.198 10 false PUL- 1.177,0.323 1.656,0.51 0.479,0.188 10 false PLL+ 5.354,1.823 6.885,2.135 1.531,0.313 10 false Airbag ECU Assembly 0.063,1.677 0.708,1.854 0.646,0.177 10 false A46 0.073,1.823 2.208,2.063 2.135,0.24 10 false Pop Up Hood Lifter Assembly LH 5.615,0.438 6.094,0.625 0.479,0.188 10 false PUL+ 1.208,1.104 1.667,1.302 0.458,0.198 10 false PLL-

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>PEDESTRIAN PROTECTION SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B198511 is output A
History B198511 is output B


Post-procedure1

a.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the pop up hood lifter assembly LH and airbag ECU assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
E449123C01
0.656,0.969 0.969,1.125 0.313,0.156 10 false *1 2.177,1.583 2.49,1.74 0.313,0.156 10 false *2 1.26,0.958 1.573,1.115 0.313,0.156 10 false *3
*1 Pop Up Hood Lifter Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the pop up hood lifter assembly LH connector.


Procedure1

a.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



b.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CHECK POP UP HOOD LIFTER ASSEMBLY LH

NG

REPAIR OR REPLACE WIRE HARNESS

4.CHECK POP UP HOOD LIFTER ASSEMBLY LH
a.
C395624C27
0.521,2.26 0.958,2.542 0.438,0.281 2.031,2.635 2.24,2.969 2.24,2.969 2.396,2.969 true 1.656,2.292 1.938,1.75 1.938,1.75 2.156,1.75 true 1.542,2.292 1.302,1.771 1.302,1.771 1.083,1.771 true 0.646,0.49 0.958,0.646 0.313,0.156 10 false *1 2.469,1.229 2.781,1.385 0.313,0.156 10 false *2 2.448,2.917 2.76,3.073 0.313,0.156 10 false *4 0.333,1.604 0.646,1.76 0.313,0.156 10 false *a 0.604,2.323 0.917,2.479 0.313,0.156 10 false A46 0.74,0.271 1.052,0.427 0.313,0.156 10 false D 1.104,0.26 1.417,0.417 0.313,0.156 10 false C 1.865,0.26 2.177,0.417 0.313,0.156 10 false B 2.021,0.26 2.333,0.417 0.313,0.156 10 false A 2.219,1.677 2.635,1.875 0.417,0.198 10 false PLL+ 0.719,1.708 1.167,1.885 0.448,0.177 10 false PLL- 1.406,0.448 1.719,0.604 0.313,0.156 10 false *3
*1 Pop Up Hood Lifter Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness
*4 SST
*a Front view of wire harness connector
(to Pop Up Hood Lifter Assembly LH)


Connect the G43 airbag ECU assembly connector.


b.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the pop up hood lifter assembly LH for measurement, as this may lead to a serious injury due to pop up hood lifter deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK POP UP HOOD LIFTER ASSEMBLY LH
5.CHECK POP UP HOOD LIFTER ASSEMBLY LH

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B198511 is not output A
B198511 is output B


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Disconnect SST from connector C.



A

REPLACE POP UP HOOD LIFTER ASSEMBLY LH

B

6.CHECK POP UP HOOD LIFTER ASSEMBLY LH CIRCUIT
6.CHECK POP UP HOOD LIFTER ASSEMBLY LH CIRCUIT

Pre-procedure1

a.
E449126C04
0.396,2.219 0.813,2.469 0.417,0.25 0.708,2.833 0.958,2.833 0.958,2.833 1.177,2.448 true 1.896,2.833 1.646,2.833 1.646,2.833 1.365,2.448 true 0.771,0.583 1.083,0.74 0.313,0.156 10 false *1 2.781,1.24 3.094,1.396 0.313,0.156 10 false *2 0.313,1.771 0.625,1.927 0.313,0.156 10 false *a 2.01,0.354 2.323,0.51 0.313,0.156 10 false B 2.385,0.365 2.698,0.521 0.313,0.156 10 false A 1.427,0.365 1.74,0.521 0.313,0.156 10 false C 0.927,0.365 1.24,0.521 0.313,0.156 10 false D 0.5,2.271 0.813,2.427 0.313,0.156 10 false A46 0.365,2.771 0.771,2.927 0.406,0.156 10 false PLL- 1.927,2.75 2.333,2.906 0.406,0.156 10 false PLL+ 1.677,0.573 1.99,0.729 0.313,0.156 10 false *3
*1 Pop Up Hood Lifter Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Pop Up Hood Lifter Assembly LH)


Disconnect the G43 airbag ECU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A46)Location & Routing

Click Connector(A46)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Pop Up Hood Lifter Assembly LH

A46-2 (PLL+) - Body ground Always 1 MΩ or higher
A46-1 (PLL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE WIRE HARNESS

7.CLEAR DTC
a.
E449128C01
0.667,0.969 0.979,1.125 0.313,0.156 10 false *1 2.146,1.594 2.458,1.75 0.313,0.156 10 false *2 1.25,0.969 1.563,1.125 0.313,0.156 10 false *3
*1 Pop Up Hood Lifter Assembly LH
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the pop up hood lifter assembly LH connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B198511 is not output A
B198511 is output B


Post-procedure1

a.

None



A

USE SIMULATION METHOD TO CHECK

B