Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROCKER PANEL MOULDING
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448287 ROCKER PANEL MOULDING A

EXTERIOR PANELS / TRIM  ROCKER PANEL MOULDING  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
B599601N04
4.073,1.01 4.292,1.125 4.292,1.125 5.052,1.125 false 4.479,0.885 4.938,1.125 false 2.469,2.01 2.667,2.115 false 1.229,1.74 1.448,1.854 1.448,1.854 1.635,1.854 false 0.667,1.292 1,0.594 1,0.594 1.156,0.594 false 1.177,1.104 1.24,0.979 1.24,0.979 1.396,0.979 false 4.073,0.448 4.156,0.292 4.156,0.292 4.313,0.292 false 4.167,2.625 4.385,2.74 4.385,2.74 4.74,2.74 false 2.823,3.49 3.042,3.604 3.042,3.604 3.396,3.604 false 2.75,2.115 2.083,2.115 false 1.958,1.75 2.115,1.948 0.156,0.198 10 false ● 5.406,1 5.563,1.198 0.156,0.198 10 false ● 3.094,2.01 3.25,2.208 0.156,0.198 10 false ● 1.719,0.885 1.875,1.083 0.156,0.198 10 false ● 4.698,0.177 4.854,0.375 0.156,0.198 10 false ● 1.49,0.49 1.646,0.688 0.156,0.198 10 false ● 3.76,3.438 4.042,3.792 0.281,0.354 18 false 1 3.229,1.969 3.51,2.323 0.281,0.354 18 false 2 2.083,1.708 2.365,2.063 0.281,0.354 18 false 3 1.833,0.854 2.115,1.208 0.281,0.354 18 false 4 4.813,0.135 5.094,0.49 0.281,0.354 18 false 5 4.833,2.677 5.146,2.875 0.313,0.198 10 false *1 3.656,3.479 3.813,3.677 0.156,0.198 10 false ● 5.51,0.958 5.792,1.313 0.281,0.354 18 false 3 1.615,0.448 1.896,0.802 0.281,0.354 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ROCKER PANEL MOULDING EMBLEM 75374A (Click here) - -
2 ROCKER PANEL MOULDING PAD 75861C (Click here) - -
3 NO. 3 MOULDING TAPE 75897B (Click here) - -
4 SIDE MUDGUARD PROTECTOR LH 76926F (Click here) - -
5 NO. 4 ROCKER PANEL MOULDING PROTECTOR 75864B (Click here) - -
6 ROCKER PANEL MOULDING COVER LH 75858A (Click here) - -

*1 ROCKER PANEL MOULDING LH - -
● Non-reusable part - -

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75374A 1.INSTALL ROCKER PANEL MOULDING EMBLEM

Z101186

Click here(Click here)

Hide 75861C 2.INSTALL ROCKER PANEL MOULDING PAD

a.
B599502C04
5.531,2.198 5.865,2.198 false 5.896,2.125 6.219,2.323 0.323,0.198 10 false *a 0.469,0.125 0.75,0.479 0.281,0.354 18 false i 0.49,0.76 0.771,1.115 0.281,0.354 18 false ii 0.469,1.865 0.75,2.219 0.281,0.354 18 false iii
*a Mark-off Line - -
V100144

Installation Area - -


i.

Clean the rocker panel moulding LH surface:

1. When reusing the rocker panel moulding LH, remove remaining double-sided tape from the rocker panel moulding LH.

2. Using a heat light, heat the rocker panel moulding LH surface.

Standard Value:
Part Temperature
Rocker Panel Moulding LH 20 to 30°C (68 to 86°F)
Rocker Panel Moulding Pad 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rocker panel moulding LH excessively.


3. Remove any remaining double-sided tape from the rocker panel moulding LH and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the rocker panel moulding pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rocker panel moulding LH surface.




ii.

Using a heat light, heat the rocker panel moulding LH and a new rocker panel moulding pad.

NOTICE:

Do not heat the rocker panel moulding LH and rocker panel moulding pad excessively.



iii.

Install the 2 rocker panel moulding pads in the position shown in the illustration.

NOTICE:

The application strength of the rocker panel moulding pad will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rocker panel moulding LH.




Hide 75897B 3.INSTALL NO. 3 MOULDING TAPE

a.
B599503C03
5.365,1.313 5.448,1.146 5.448,1.146 5.698,1.146 false 6.031,2.854 6.115,2.688 6.115,2.688 6.365,2.688 false 1.406,2.854 1.729,2.854 false 6.438,2.615 6.75,2.813 0.313,0.198 10 false *1 5.76,1.073 6.073,1.271 0.313,0.198 10 false *2 0.521,0.531 0.802,0.885 0.281,0.354 18 false i 0.5,1.49 0.781,1.844 0.281,0.354 18 false ii 0.479,2.458 0.76,2.813 0.281,0.354 18 false iii 1.771,2.771 2.083,2.969 0.313,0.198 10 false *a
*1 No. 4 Rocker Panel Moulding Protector *2 Rocker Panel Moulding Cover LH
*a Mark-off Line - -
V100144

Installation Area - -


i.

Clean the installation area surface.


ii.

Using a heat light, heat the installation area and a new No. 3 moulding tape.

Standard Value:
Part Temperature
No. 4 Rocker Panel Moulding Protector 20 to 30°C (68 to 86°F)
Rocker Panel Moulding Cover LH 20 to 30°C (68 to 86°F)
No. 3 Moulding Tape 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the installation area and No. 3 moulding tape excessively.



iii.

Install the 3 No. 3 moulding tapes in the position shown in the illustration.

NOTICE:

The application strength of the No. 3 moulding tape will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the installation area.




Hide 76926F 4.INSTALL SIDE MUDGUARD PROTECTOR LH

a.
B599504C02
4.01,4.417 4.646,4.219 true 0.469,0.24 0.75,0.594 0.281,0.354 18 false i 5.208,2.198 5.49,2.552 0.281,0.354 18 false ii 3.781,5.281 4.063,5.635 0.281,0.354 18 false iii 4.698,4.146 5.01,4.344 0.313,0.198 10 false *a
*a Mark-off Line - -
V100144

Installation Area - -


i.

Clean the rocker panel moulding LH surface:

1. When reusing the rocker panel moulding LH, remove remaining double-sided tape from the rocker panel moulding LH.

2. Using a heat light, heat the rocker panel moulding LH surface.

Standard Value:
Part Temperature
Rocker Panel Moulding LH 20 to 30°C (68 to 86°F)
Side Moulding Protector LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rocker panel moulding LH excessively.


3. Remove any remaining double-sided tape from the rocker panel moulding LH and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the side moulding protector LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rocker panel moulding LH surface.




ii.

Using a heat light, heat the rocker panel moulding LH and a new side moulding protector LH.

NOTICE:

Do not heat the rocker panel moulding LH and side moulding protector LH excessively.



iii.

Install the side moulding protector LH in the position shown in the illustration.

NOTICE:

The application strength of the side moulding protector LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rocker panel moulding LH.




Hide 75864B 5.INSTALL NO. 4 ROCKER PANEL MOULDING PROTECTOR

a.
B599505C02
3.844,4.542 4.698,4.167 true 0.469,0.219 0.75,0.573 0.281,0.354 18 false i 5.198,2.198 5.479,2.552 0.281,0.354 18 false ii 3.125,5.229 3.406,5.583 0.281,0.354 18 false iii 4.771,4.052 5.083,4.25 0.313,0.198 10 false *a
*a Mark-off Line - -
V100144

Installation Area - -


i.

Clean the rocker panel moulding LH surface:

1. When reusing the rocker panel moulding LH, remove remaining double-sided tape from the rocker panel moulding LH.

2. Using a heat light, heat the rocker panel moulding LH surface.

Standard Value:
Part Temperature
Rocker Panel Moulding LH 20 to 30°C (68 to 86°F)
No. 4 Rocker Panel Moulding Protector 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rocker panel moulding LH excessively.


3. Remove any remaining double-sided tape from the rocker panel moulding LH and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the No. 4 rocker panel moulding protector with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rocker panel moulding LH surface.




ii.

Using a heat light, heat the rocker panel moulding LH and a new No. 4 rocker panel moulding protector.

NOTICE:

Do not heat the rocker panel moulding LH and No. 4 rocker panel moulding protector excessively.



iii.

Install the No. 4 rocker panel moulding protector in the position shown in the illustration.

NOTICE:

The application strength of the No. 4 rocker panel moulding protector will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rocker panel moulding LH.




Hide 75858A 6.INSTALL ROCKER PANEL MOULDING COVER LH

a.
B599506C02
3.813,4.573 4.229,4.427 true 0.458,0.219 0.74,0.573 0.281,0.354 18 false i 5.208,2.188 5.49,2.542 0.281,0.354 18 false ii 3.25,5.365 3.531,5.719 0.281,0.354 18 false iii 4.313,4.333 4.625,4.531 0.313,0.198 10 false *a
*a Mark-off Line - -
V100144

Installation Area - -


i.

Clean the rocker panel moulding LH surface:

1. When reusing the rocker panel moulding LH, remove remaining double-sided tape from the rocker panel moulding LH.

2. Using a heat light, heat the rocker panel moulding LH surface.

Standard Value:
Part Temperature
Rocker Panel Moulding LH 20 to 30°C (68 to 86°F)
Rocker Panel Moulding Cover LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rocker panel moulding LH excessively.


3. Remove any remaining double-sided tape from the rocker panel moulding LH and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the rocker panel moulding cover LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rocker panel moulding LH surface.




ii.

Using a heat light, heat the rocker panel moulding LH and a new rocker panel moulding cover LH.

NOTICE:

Do not heat the rocker panel moulding LH and rocker panel moulding cover LH excessively.



iii.

Install the rocker panel moulding cover LH in the position shown in the illustration.

NOTICE:

The application strength of the rocker panel moulding cover LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rocker panel moulding LH.