Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WINDSHIELD OUTSIDE MOULDING
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448290 WINDSHIELD OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  WINDSHIELD OUTSIDE MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B604651N02
3.552,1.417 3.802,1.417 3.802,1.417 3.885,1.583 false 2.167,0.74 2.25,0.573 2.25,0.573 2.375,0.573 false 4.604,1.479 4.719,1.052 4.719,1.052 4.948,1.052 false 4.958,1.667 5.01,1.49 5.01,1.49 5.188,1.49 false 3.385,1.302 3.667,1.656 0.281,0.354 18 false 1 5.156,0.917 5.375,1.188 0.219,0.271 18 false 2 2.719,0.438 3,0.792 0.281,0.354 18 false 3 5.021,0.958 5.177,1.156 0.156,0.198 10 false ● 5.656,1.354 5.938,1.708 0.281,0.354 18 false 4 5.521,1.396 5.677,1.594 0.156,0.198 10 false ● 4.698,1.354 5.156,1.552 0.458,0.198 10 false x 5 5.146,1.688 5.604,1.885 0.458,0.198 10 false x 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 LOWER WINDSHIELD MOULDING OUTSIDE LH 75536D (Click here) - -
2 NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP 75545B - - -
3 WINDSHIELD GLASS 56111 (Click here) - -
4 NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP 75547C (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 3 windshield outside moulding clip removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link

Windshield glass (Including removal and installation)


Adjust forward recognition camera
·

Dynamic radar cruise control system

·

Front camera system

·

Lane tracing assist system

·

Road sign assist system

·

Pre-collision system

·

Adaptive high beam system

·

Automatic high beam system


One Time Recognition:
(Click here)
Sequential Recognition:
(Click here)
Driving Adjustment:
(Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75536D 1.REMOVE LOWER WINDSHIELD MOULDING OUTSIDE LH

a.
B599509N02
2.813,0.156 3.094,0.51 0.281,0.354 18 false i 0.104,0.104 0.271,0.385 0.167,0.281 18 true ii 3.771,0.51 3.938,0.792 0.167,0.281 18 true ii

i.

Put protective tape around the lower windshield moulding outside LH.


ii.

Detach the claw and remove the lower windshield moulding outside LH.



Hide 75545B 2.REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

a.
B599510


Hide 56111 3.REMOVE WINDSHIELD GLASS

Z101186

HINT:

Perform the following procedure only when replacement of the No. 3 windshield outside moulding clip is necessary.

Click here(Click here)



Hide 75547C 4.REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

Z101186

HINT:

Perform the following procedure only when replacement of the No. 3 windshield outside moulding clip is necessary.



a.
B604652C02
0.927,0.979 0.615,0.635 false 6.323,0.438 6.5,0.375 false 0.427,1.063 0.583,1.26 0.156,0.198 10 false A 0.958,0.99 1.271,1.188 0.313,0.198 10 false *a 6.531,0.292 6.844,0.49 0.313,0.198 10 false *b 0.531,0.104 1.156,0.438 0.625,0.333 18 false i, ii 5.229,0.219 5.51,0.573 0.281,0.354 18 false iii
*a Tape *b Flange


i.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


ii.

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement Area Measurement
A 5.0 mm (0.197 in.) - -


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the No. 3 windshield outside moulding clips to drill off the No. 3 windshield outside moulding clip flanges, and remove the 5 No. 3 windshield outside moulding clips.

CAUTION:

Be careful of the drilled No. 3 windshield outside moulding clips, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

·

Prying the No. 3 windshield outside moulding clips with the drill may damage the No. 3 windshield outside moulding clip installation holes or drill bit.