Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM37H0E _59 Vehicle Exterior _095305 WINDOW / GLASS _0448200 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E453922N01
2.458,0.99 2.781,0.542 2.781,0.542 3.042,0.542 false 2.729,2.281 2.833,2.396 2.833,2.396 3.219,2.396 false 2.385,2.083 2.573,2.083 false 3.073,0.417 3.375,0.698 0.302,0.281 18 false 1 3.542,2.25 3.813,2.51 0.271,0.26 18 false 2 1.531,0.771 1.823,0.948 0.292,0.177 10 false x 6 1.656,2.219 1.969,2.417 0.313,0.198 10 false x 2 2.604,2.031 2.917,2.229 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 UPPER RADIATOR SUPPORT SEAL 53292A - - -
2 FRONT FENDER UPPER PROTECTOR LH 53826A (Click here) - -

*1 CENTER HOOD CUSHION - -

E455809N03
3.635,0.542 3,0.542 false 6.302,1.885 5.688,1.885 false 4.969,3.094 5.479,3.094 false 3.115,2.75 3.115,3.01 false 4.448,3.344 4.448,3.74 false 4.667,5.198 4.667,5.479 false 4.208,4.552 4.677,4.552 false 1.448,3.302 1.448,3.667 false 2.927,2.125 2.917,1.802 2.917,1.802 3.479,1.802 false 6.583,1.771 6.885,2.01 0.302,0.24 18 false 9 2.677,0.417 2.99,0.677 0.313,0.26 18 false 10 5.74,2.979 5.99,3.24 0.25,0.26 18 false 3 3.698,1.688 3.927,1.938 0.229,0.25 18 false 3 4.635,3.719 4.917,4 0.281,0.281 18 false 4 3.281,3.01 3.5,3.26 0.219,0.25 18 false 5 1.396,3.698 1.667,4 0.271,0.302 18 false 6 4.969,4.417 5.438,4.719 0.469,0.302 18 false 8 4.615,5.49 4.906,5.781 0.292,0.292 18 false 7 2.448,2.927 2.906,3.125 0.458,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

3 FRONT WIPER ARM HEAD CAP 85292B (Click here) - -
4 FRONT WIPER ARM AND BLADE ASSEMBLY LH - (Click here) - -
5 FRONT WIPER ARM AND BLADE ASSEMBLY RH - (Click here) - -
6 COWL TOP VENTILATOR LOUVER PROTECTOR RH 55782 - - -
7 COWL TOP VENTILATOR LOUVER PROTECTOR LH 55783 - - -
8 COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY 55708 (Click here) - -
9 LOWER WINDSHIELD MOULDING OUTSIDE LH 75536D (Click here) - -
10 LOWER WINDSHIELD MOULDING OUTSIDE 75535A (Click here) - -

E455811N01
4.594,1.76 4.594,2.49 false 4.469,2.5 5.021,2.854 0.552,0.354 18 false 11

Procedure Part Name Code
Z101186

Z101188

Z101187

11 ROOF HEADLINING ASSEMBLY 63310 - - -

E463033N03
0.167,0.75 7,2.5 6.833,1.75 2.333,1.802 2.333,2.083 false 5.01,4.458 5.01,3.917 false 3.583,0.75 3.583,2.5 false 4.917,1.75 4.917,2.083 false 2.594,4.438 2.594,3.896 false 4.885,4.458 5.438,4.813 0.552,0.354 18 false 12 2.198,2.083 2.75,2.438 0.552,0.354 18 false 13 3.625,0.844 4,1.083 0.375,0.24 12 false *B 0.292,0.833 0.667,1.073 0.375,0.24 12 false *A 4.781,2.083 5.333,2.438 0.552,0.354 18 false 14 2.469,4.448 3.021,4.802 0.552,0.354 18 false 15

Procedure Part Name Code
Z101186

Z101188

Z101187

12 FORWARD RECOGNITION CAMERA 8646C - - -
13 INNER REAR VIEW MIRROR ASSEMBLY 87810 - - -
14 INNER REAR VIEW MIRROR ASSEMBLY 87810 - - -
15 RAIN SENSOR 89941 - - -

*A for Digital Inner Mirror *B for EC Inner Mirror

E463891N01
0.479,0.104 6.292,1.073 5.813,0.969 5.177,1.781 5.177,1.417 5.177,1.417 5.823,1.417 false 5.51,2.49 6.229,2.49 false 3.146,0.104 3.146,1.073 false 2.344,0.927 1.583,0.927 false 4.781,0.813 4.781,0.677 4.781,0.677 4.24,0.677 false 4.313,0.24 5.375,0.24 false 5.208,0.74 5.208,0.24 false 3.938,0.333 4.406,0.333 4.406,0.333 4.406,0.667 false 1.49,0.417 2.188,0.417 2.188,0.417 2.188,0.927 false 2.406,1.594 2.906,1.594 false 5.479,3.708 5.958,3.708 false 3.073,4.958 3.073,4.76 3.073,4.76 3.792,4.76 false 2.563,5.604 3,5.604 false 3.688,4.219 3.688,4.052 3.688,4.052 4.208,4.052 false 1.917,3.74 1.563,3.74 false 3.365,4.563 3.104,4.563 false 5.656,4.677 6.115,4.677 false 1.375,2.594 1.375,2.885 1.375,2.885 1.74,2.885 false 0.5,4.74 0.323,4.74 0.323,4.74 0.323,5.333 false 0.656,4.958 0.323,4.958 false 0.885,5.177 0.323,5.177 false 6.208,1.302 6.76,1.656 0.552,0.354 18 false 20 6.094,1.333 6.25,1.531 0.156,0.198 10 false ● 6.438,2.365 6.771,2.615 0.333,0.25 18 false 16 6.333,3.604 6.625,3.875 0.292,0.271 18 false 22 3.208,0.135 3.583,0.375 0.375,0.24 12 false *B 0.542,0.146 0.917,0.385 0.375,0.24 12 false *A 1.292,0.802 1.844,1.156 0.552,0.354 18 false 17 5.875,0.135 6.427,0.49 0.552,0.354 18 false 19 3.917,0.563 4.24,0.813 0.323,0.25 18 false 18 1.25,3.594 1.802,3.948 0.552,0.354 18 false 26 4.156,4.656 4.5,4.917 0.344,0.26 18 false 22 4.031,4.698 4.188,4.896 0.156,0.198 10 false ● 1.198,0.833 1.354,1.031 0.156,0.198 10 false ● 3.802,0.635 3.958,0.833 0.156,0.198 10 false ● 5.74,0.167 5.896,0.365 0.156,0.198 10 false ● 6.208,3.635 6.365,3.833 0.156,0.198 10 false ● 0.604,5.354 0.948,5.615 0.344,0.26 18 false 24 4.531,3.948 4.875,4.208 0.344,0.26 18 false 21 4.438,3.979 4.594,4.177 0.156,0.198 10 false ● 3.292,5.5 3.448,5.698 0.156,0.198 10 false ● 2,1.5 2.156,1.698 0.156,0.198 10 false ● 2.115,1.469 2.406,1.74 0.292,0.271 18 false 22 1.135,3.615 1.292,3.813 0.156,0.198 10 false ● 2.813,4.396 3.365,4.75 0.552,0.354 18 false 26 2.698,4.417 2.854,4.615 0.156,0.198 10 false ● 6.49,4.573 6.813,4.844 0.323,0.271 18 false 23 6.365,4.594 6.521,4.792 0.156,0.198 10 false ● 2.094,2.75 2.417,3.021 0.323,0.271 18 false 23 1.969,2.781 2.125,2.979 0.156,0.198 10 false ● 3.396,5.469 3.74,5.729 0.344,0.26 18 false 25 0.479,5.385 0.635,5.583 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

16 WINDSHIELD GLASS 56111 (Click here) - -
17 NO. 1 WINDSHIELD GLASS STOPPER 56115A (Click here) - -
18 NO. 2 WINDSHIELD GLASS STOPPER 56116C (Click here) - -
19 NO. 1 WINDSHIELD GLASS STOPPER 56115A (Click here) - -
20 WINDSHIELD OUTSIDE MOULDING 75533G (Click here) - -
21 COWL TOP SILENCER PAD 55783A (Click here) - -
22 WINDOW GLASS ADHESIVE DAM 56117A (Click here) - -
23 NO. 2 WINDOW GLASS ADHESIVE DAM 56118A (Click here) - -
24 WINDOW DEFOGGER WIRE GUIDE 67398A (Click here) - -
25 FRONT WINDOW INNER CENTER MOULDING 56153C (Click here) - -
26 WINDSHIELD GLASS RETAINER 56114 (Click here) - -

*A for 1-piece Type *B for 2-piece Type
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the windshield glass removal/installation are shown below.

Necessary Procedure after parts Removed/Installed/Replaced
Replacement Part or Procedures Necessary Procedure Effect/Inoperative when are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Forward recognition camera

·

Windshield glass (Including removal and installation)


Adjust forward recognition camera
·

Dynamic radar cruise control system

·

Front camera system

·

Lane tracing assist system

·

Road sign assist system

·

Pre-collision system

·

Adaptive high beam system

·

Automatic high beam system


One Time Recognition:
(Click here)
Sequential Recognition:
(Click here)
Driving Adjustment:
(Click here)

NOTICE:
·

When replacing the windshield glass of a vehicle equipped with a forward recognition camera make sure to use genuine windshield glass for the forward recognition camera. A windshield glass other than a genuine windshield glass for the forward recognition camera does not have installation brackets for the forward recognition camera. Therefore, the forward recognition camera be installed. If the forward recognition camera are mounted on a windshield glass that is not a genuine windshield glass for the forward recognition camera, the systems using the forward recognition camera may not operate properly because of the transmittance of the windshield glass and the shape of the black ceramic parts.

·

Be sure to use the windshield glass adhesive (specialized for high-rigidity specification vehicles) as the adhesive for replacing the windshield glass.

·

Be sure to use the windshield glass adhesive (specialized for high-rigidity specification vehicles) as the adhesive for adjusting the windshield glass.



PROCEDURE

Hide 53292A 1.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 53826A 2.REMOVE FRONT FENDER UPPER PROTECTOR LH

Z101186

Click here(Click here)

Hide 85292B 3.REMOVE FRONT WIPER ARM HEAD CAP

Z101186

Click here(Click here)

Hide 4.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Z101186

Click here(Click here)

Hide 5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Z101186

Click here(Click here)

Hide 55782 6.REMOVE COWL TOP VENTILATOR LOUVER PROTECTOR RH

Hide 55783 7.REMOVE COWL TOP VENTILATOR LOUVER PROTECTOR LH

Hide 55708 8.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 75536D 9.REMOVE LOWER WINDSHIELD MOULDING OUTSIDE LH

Z101186

Click here(Click here)

Hide 75535A 10.REMOVE LOWER WINDSHIELD MOULDING OUTSIDE

Z101186

Use the same procedure described for the LH side.

Hide 63310 11.REMOVE ROOF HEADLINING ASSEMBLY

Hide 8646C 12.REMOVE FORWARD RECOGNITION CAMERA

Hide 87810 13.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (for Digital Inner Mirror)

Hide 87810 14.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (for EC Inner Mirror)

Hide 89941 15.REMOVE RAIN SENSOR

Hide 56111 16.REMOVE WINDSHIELD GLASS

Z101186

NOTICE:
·

The windshield glass may fall during work. Therefore, use suction cups to hold the windshield glass from outside the vehicle.

·

Be careful not to damage the windshield glass when cutting as the No. 1 windshield glass stopper and No. 2 windshield glass stopper are installed to the windshield glass.

·

When removing the windshield glass from the body, do not damage the front window inner center moulding. (When reusing a front window inner center moulding)

·

When removing the windshield glass from the body, do not damage the windshield deicer wire harness. (When reusing a windshield glass with windshield deicer)

·

When replacing the front window inner center moulding, cellophane tape can be used as a substitute for the harness clamp. (w/ Windshield Deicer)



HINT:

Depending on the vehicle, 1-piece type or 2-piece type windshield glass stoppers may be installed.



a.
E453928C01
4.896,1.385 4.563,1.24 4.563,1.24 5.021,1.198 true 0.927,0.271 1.365,0.552 0.438,0.281 10 false *a 4.094,0.271 4.406,0.427 0.313,0.156 10 false *b 0.469,0.083 0.75,0.438 0.281,0.354 18 false i 4.333,1.156 4.552,1.344 0.219,0.188 10 true *c
*a When new the Windshield Glass *b When reusing the Windshield Glass
*c Matchmarks - -


i.

Apply protective tape on the body surface around the outer edge of the windshield glass.

NOTICE:

When reusing the windshield glass, apply adhesive tape to the windshield glass and body panel, and place matchmarks using a pen before removing.




b.
E453927C01
4.115,0.583 4.542,0.646 false 5.49,0.615 5.917,0.677 false 0.438,0.094 0.719,0.448 0.281,0.354 18 false i 3.958,0.5 4.24,0.854 0.281,0.354 10 false *a 5.323,0.531 5.604,0.885 0.281,0.354 10 false *a 3.667,0.198 4.042,0.438 0.375,0.24 12 false *A 5.333,0.198 5.708,0.438 0.375,0.24 12 false *B
*A for Normal Roof *B for Panoramic Moon Roof
*a Cut - -


i.

Using a utility knife, cut the windshield outside moulding.

NOTICE:
·

Do not damage the windshield glass or body surface.

·

If the body panel is damaged, perform rust-prevention treatment after removing the windshield glass.





c.

w/ windshield deicer:

E455816N01
2.063,0.146 2.344,0.5 0.281,0.354 18 false i

i.

Disconnect the connector.



d.
E453930C01
3.094,0.594 2.469,0.323 true 4,0.896 5.26,0.49 true 0.448,0.083 0.729,0.438 0.281,0.354 18 false i 2.313,0.24 2.625,0.438 0.313,0.198 10 false *a 5.302,0.406 5.615,0.604 0.313,0.198 10 false *a
*a Suction Cups - -


i.

Install the suction cups to the windshield glass.



e.
E459255C01
3.125,0.865 3.615,0.458 3.615,0.458 4.052,0.885 true 2.854,1.75 3.573,2.146 3.573,2.146 4.323,1.74 true 2.698,1.771 2.146,1.917 2.146,1.917 2.865,1.948 true 3.552,0.292 3.865,0.49 0.313,0.198 10 false *1 3.51,2.167 3.823,2.365 0.313,0.198 10 false *2 1.99,1.844 2.302,2.042 0.313,0.198 10 false *a 0.406,0.094 0.688,0.448 0.281,0.354 18 false i
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper
*a Piano Wire - -


i.

When using a piano wire, perform the following procedure.

1. Pass the piano wire (0.6 mm is appropriate) and install both ends on the mighty puller as shown in the illustration.

2. Pull the piano wire back and forth and cut through the adhesive of the windshield glass leaving the windshield glass stopper.

NOTICE:
·

When working near the instrument panel, place a plastic sheet so that the piano wire does not damage the instrument panel.

·

When working near the curtain shield airbag, be careful not to damage it with the piano wire.

·

Do not forcefully allow the piano wire to come to contact with the edges of the windshield glass.

·

Be careful as the piano wire will break if it crosses itself.





f.
E459256C01
1.938,0.781 2.104,0.854 false 5.448,0.833 5.677,0.906 false 5.125,0.635 4.938,0.875 false 5.604,3.344 5.875,3.344 false 2.156,3.344 2.333,3.344 false 0.958,0.146 1.385,0.469 0.427,0.323 12 false *A 4.438,0.146 4.865,0.469 0.427,0.323 12 false *B 2.146,0.813 2.5,1.125 0.354,0.313 10 false *1 5.719,0.865 6.073,1.177 0.354,0.313 10 false *1 4.875,0.885 5.229,1.198 0.354,0.313 10 false *2 5.917,3.292 6.271,3.604 0.354,0.313 10 false *3 2.354,3.292 2.708,3.604 0.354,0.313 10 false *3 0.396,0.063 0.677,0.417 0.281,0.354 18 false i
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper
*3 Windshield Glass Retainer - -


i.

Holding the suction cups, detach the 2 windshield glass stoppers and 2 windshield glass retainers, and remove the windshield glass.

NOTICE:

Be careful not to drop the windshield glass.




Hide 56115A 17.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

When reusing the windshield glass:

E455818C01
2.229,0.063 2.542,0.26 0.313,0.198 10 false *a 0.427,0.063 0.708,0.417 0.281,0.354 18 false i
*a Backside - -


i.

Using a scraper, remove the 2 No. 1 windshield glass stoppers.

NOTICE:
·

Do not damage the windshield glass.

·

Always replace the installed No. 1 windshield glass stopper with a new 2-piece type No. 1 windshield glass stopper.





Hide 56116C 18.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

When reusing the windshield glass:

E455819C01
2.271,0.063 2.583,0.26 0.313,0.198 10 false *a 0.396,0.094 0.677,0.448 0.281,0.354 18 false i
*a Backside - -


i.

Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:
·

Do not damage the windshield glass.

·

Always replace the installed No. 2 windshield glass stopper with a new 2-piece type No. 2 windshield glass stopper.





Hide 56115A 19.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
E453936C01
0.448,0.073 0.729,0.427 0.281,0.354 18 false i

i.

Remove the 2 No. 1 window glass stoppers from the body.

NOTICE:

Always replace the installed No. 1 windshield glass stopper with a new 2-piece type No. 1 windshield glass stoppers.




Hide 75533G 20.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

When reusing the windshield glass:

E459247C02
0.323,0.042 0.604,0.396 0.281,0.354 18 false i 2.177,0.104 2.49,0.302 0.313,0.198 10 false *a
*a Backside - -


i.

Using a scraper, remove the windshield outside moulding.

NOTICE:
·

Do not damage the windshield glass.

·

Always replace the installed windshield outside moulding with a new windshield outside moulding.





Hide 55783A 21.REMOVE COWL TOP SILENCER PAD

a.

When reusing the windshield glass:

E459248C01
0.323,0.042 0.604,0.396 0.281,0.354 18 false i 2.156,0.063 2.469,0.26 0.313,0.198 10 false *a
*a Backside - -


i.

Using a scraper, remove the cowl top silencer pad.

NOTICE:
·

Do not damage the windshield glass.

·

Always replace the installed cowl top silencer pad with a new cowl top silencer pad.





Hide 56117A 22.REMOVE WINDOW GLASS ADHESIVE DAM

a.

When reusing the windshield glass: (for Lower side of windshield glass)

E459249C01
2.26,0.094 2.573,0.292 0.313,0.198 10 false *a 0.385,0.073 0.667,0.427 0.281,0.354 18 false i
*a Backside - -


i.

Using a scraper, remove the window glass adhesive dam.

NOTICE:
·

Do not damage the windshield glass.

·

Always replace the installed windshield glass adhesive dam with a new windshield glass adhesive dam.





b.

When reusing the windshield glass: (for Both sides of windshield glass)

E459250C01
0.333,0.042 0.615,0.396 0.281,0.354 18 false i 2.083,0.052 2.396,0.25 0.313,0.198 10 false *a
*a Backside - -


i.

Using a scraper, remove the 2 window glass adhesive dams.

NOTICE:
·

Do not damage the windshield glass.

·

Always replace the installed windshield glass adhesive dam with a new windshield glass adhesive dam.





Hide 56118A 23.REMOVE NO. 2 WINDOW GLASS ADHESIVE DAM

a.

When reusing the windshield glass:

E459253C01
0.385,0.083 0.667,0.438 0.281,0.354 18 false i 1.74,0.417 2.052,0.615 0.313,0.198 10 false *a
*a Backside - -


i.

Using a scraper, remove the 2 No. 2 window glass adhesive dams.

NOTICE:
·

Using a scraper, remove the No. 2 window glass adhesive dam.

·

Always replace the installed No. 2 window glass adhesive dam with a new No. 2 window glass adhesive dam.





Hide 67398A 24.REMOVE WINDOW DEFOGGER WIRE GUIDE

HINT:

Perform the following procedures if replacing the window defogger wire guide.


a.

When reusing the windshield glass:

E463894C01
0.406,0.073 0.688,0.427 0.281,0.354 18 false i 1.781,0.167 2.094,0.365 0.313,0.198 10 false *a
*a Backside - -


i.

Using a scraper, remove the window defogger wire guide.



Hide 56153C 25.REMOVE FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedures if replacing the front window inner center moulding.


a.

When reusing the windshield glass:

E459251C01
2.135,0.031 2.448,0.229 0.313,0.198 10 false *a
*a Backside - -


i.

Using a scraper, remove the front window inner center moulding.

NOTICE:
·

Do not damage the windshield glass.

·

Always replace the installed front window inner center moulding with a new front window inner center moulding.





Hide 56114 26.REMOVE WINDSHIELD GLASS RETAINER

a.

When reusing the windshield glass:

E459252C01
0.333,0.052 0.615,0.406 0.281,0.354 18 false i 2.083,0.021 2.396,0.219 0.313,0.198 10 false *a
*a Backside - -


i.

Using a scraper, remove the windshield glass retainer.

NOTICE:
·

Do not damage the windshield glass.

·

Always replace the installed windshield glass retainer with a new windshield glass retainer.