Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Front Door)
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448295 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B604622N07
2.427,3.031 3.417,3.219 0.99,0.188 0.198,3.438 0.458,2.833 0.458,2.833 0.708,2.833 false 4.469,4.865 4.552,5.031 4.552,5.031 4.802,5.031 false 4.313,4.615 4.396,4.448 4.396,4.448 4.646,4.448 false 2.146,3.865 2.229,3.698 2.229,3.698 2.479,3.698 false 2.5,2.302 2.583,2.135 2.583,2.135 2.75,2.135 false 5.656,1.021 5.74,0.854 5.74,0.854 5.99,0.854 false 4.49,1.156 4.573,1.323 4.573,1.323 4.823,1.323 false 2.813,0.76 2.896,0.594 2.896,0.594 3.146,0.594 false 6.49,0.219 6.823,0.219 false 1.948,2.958 2.031,3.125 2.031,3.125 2.427,3.125 false 2.052,2.906 2.365,3.104 0.313,0.198 10 false x 2 3.104,2.01 3.385,2.365 0.281,0.354 18 false 7 3.24,0.427 3.521,0.781 0.281,0.354 18 false 6 0.771,2.708 1.052,3.063 0.281,0.354 18 false 5 2.552,3.563 2.833,3.917 0.281,0.354 18 false 4 6.208,0.729 6.49,1.083 0.281,0.354 18 false 3 5.052,1.188 5.333,1.542 0.281,0.354 18 false 2 6.313,0.094 6.802,0.354 0.49,0.26 18 false 1 6.073,0.771 6.229,0.969 0.156,0.198 10 false ● 4.896,4.896 5.177,5.25 0.281,0.354 18 false 8 4.708,4.323 5.063,4.615 0.354,0.292 18 false 9 3.542,5.115 3.854,5.313 0.313,0.198 10 false x 3 4.906,1.229 5.063,1.427 0.156,0.198 10 false ● 2.479,3.052 4.688,3.208 2.208,0.156 8 false 8.0 (82, 71 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REPAIR INSTRUCTION - (Click here) - -
2 FRONT DOOR NO. 3 STRIPE LH 75986B - - -
3 FRONT DOOR NO. 4 STRIPE LH 75966B - - -
4 FRONT DOOR WEATHERSTRIP LH 67862 - - -
5 UPPER DOOR FRAME GARNISH LH 67664 - - -
6 FRONT DOOR GLASS RUN LH 68151C - - -
7 FRONT DOOR GLASS SUB-ASSEMBLY LH 68102 (Click here) - -
8 HOLE PLUG - - - -
9 FRONT DOOR SERVICE HOLE COVER LH 67832 - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

B599856N06
0.167,4.583 3.833,5.667 3.667,1.083 0.354,0.229 0.583,0.229 false 0.302,0.604 0.583,0.604 false 2,4.583 2,5.667 false 2.875,5.083 2.958,5.25 2.958,5.25 3.208,5.25 false 0.698,5.271 0.948,5.271 0.948,5.271 1.031,5.104 false 1.333,3.969 1.583,3.969 1.583,3.969 1.667,4.135 false 3.083,3.042 3.167,2.875 3.167,2.875 3.417,2.875 false 4.688,3.052 4.938,3.052 4.938,3.052 5.021,2.885 false 5.781,3.135 5.865,3.302 5.865,3.302 6.115,3.302 false 0.354,1 0.583,1 false 3.698,2.354 3.781,2.188 3.781,2.188 4.031,2.188 false 0.677,0.49 1.531,0.938 0.854,0.448 18 false 19 0.688,0.094 1.406,0.531 0.719,0.438 18 false 17 1.719,3.021 2.031,3.219 0.313,0.198 10 false x 2 0.24,4.635 0.615,4.875 0.375,0.24 12 false *A 2.063,4.625 2.438,4.865 0.375,0.24 12 false *B 4.104,2.063 4.906,2.5 0.802,0.438 18 false 11 0.354,5.156 1.073,5.573 0.719,0.417 18 false 14 3.25,5.115 4.115,5.5 0.865,0.385 18 false 15 3.49,2.719 4.458,3.5 0.969,0.781 18 false 13 6.167,3.177 6.708,3.906 0.542,0.729 18 false 12 1,3.854 1.979,4.365 0.979,0.51 18 false 16 4.365,2.938 5.052,3.656 0.688,0.719 18 false 10 0.656,0.875 1.74,1.427 1.083,0.552 18 false 18, 20

Procedure Part Name Code
Z101186

Z101188

Z101187

10 FRONT DOOR FRONT BELT SEAL LH 68193C - - -
11 FRONT DOOR INNER GLASS WEATHERSTRIP LH 68172A - - -
12 FRONT DOOR LOWER FRAME BRACKET GARNISH LH 67492A - - -
13 FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH 67602 - - -
14 POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL - - - -
15 POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL - - - -
16 FRONT DOOR INSIDE HANDLE BEZEL PLUG LH 69284C - - -
17 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
18 INITIALIZATION POWER WINDOW CONTROL SYSTEM - - - (Click here)
19 CHECK POWER WINDOW OPERATION - (Click here) - -
20 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

*A for Driver Side *B for Front Passenger Side

HINT:
·

Use the same procedure for both the RH and LH side.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.
B599854C03
6.396,0.854 6.49,0.698 false 6.667,1.385 6.76,1.229 false 1.146,2.583 1.24,2.427 false 2.844,3.073 3,3.208 false 4.885,3.542 5.094,3.542 false 3.531,3.729 3.625,3.844 false 1.667,3.74 1.781,3.865 false 0.865,4.844 0.823,4.927 false 0.323,0.802 0.281,0.885 false 5.677,3.615 5.792,3.74 false 1.688,5.469 1.813,5.344 false 4.688,5.281 4.875,5.073 true 2.865,3.552 3.094,3.646 false 1.115,3.375 1.344,3.469 false 0.896,1.865 1.219,2.115 0.323,0.25 12 false *A 2.927,1.854 3.25,2.104 0.323,0.25 12 false *B 0.49,0.198 0.813,0.448 0.323,0.25 18 false i 2.521,0.208 2.844,0.458 0.323,0.25 18 false ii 3.729,0.198 4.052,0.448 0.323,0.25 18 false iii 6.063,0.188 6.385,0.438 0.323,0.25 18 false iv 0.542,1.823 0.865,2.073 0.323,0.25 18 false v 4.698,1.823 5.021,2.073 0.323,0.25 18 false vi 0.427,4.302 0.75,4.552 0.323,0.25 18 false vii 4.719,4.333 5.042,4.583 0.323,0.25 18 false viii 6.49,0.573 6.802,0.771 0.313,0.198 10 false *1 6.49,1.333 6.802,1.531 0.313,0.198 10 false *1 5.792,0.646 6.104,0.844 0.313,0.198 10 false *a 5.802,1.063 6.115,1.26 0.313,0.198 10 false *b 4.042,0.208 4.354,0.406 0.313,0.198 10 false *b 4.865,0.208 5.177,0.406 0.313,0.198 10 false *a 5.938,4.448 6.25,4.646 0.313,0.198 10 false *b 5.938,4.865 6.25,5.063 0.313,0.198 10 false *b 5.938,5.271 6.25,5.469 0.313,0.198 10 false *a 1.021,2.594 1.333,2.792 0.313,0.198 10 false *c 2.677,2.938 2.99,3.135 0.313,0.198 10 false *c 4.729,3.458 5.042,3.656 0.313,0.198 10 false *c 1.75,3.875 2.063,4.073 0.313,0.198 10 false *d 3.594,3.865 3.906,4.063 0.313,0.198 10 false *d 5.979,3.354 6.292,3.552 0.313,0.198 10 false *e 1.688,4.531 2,4.729 0.313,0.198 10 false *f 0.729,4.917 1.042,5.115 0.313,0.198 10 false *g 0.198,0.875 0.51,1.073 0.313,0.198 10 false *g 1.646,2.125 1.958,2.323 0.313,0.198 10 false *i 3.323,3.521 3.635,3.719 0.313,0.198 10 false *j 2.25,2.865 2.573,3.063 0.323,0.198 10 false *l 3.979,2.885 4.302,3.083 0.323,0.198 10 false *l 5.833,3.698 6.146,3.896 0.313,0.198 10 false *1 0.677,2.594 0.99,2.792 0.313,0.198 10 false *k 2.885,2.583 3.198,2.781 0.313,0.198 10 false *k 1.531,5.427 1.844,5.625 0.313,0.198 10 false *1 4.875,4.927 5.188,5.125 0.313,0.198 10 false *1 0.938,3.292 1.25,3.49 0.313,0.198 10 false *1 2.688,3.458 3,3.656 0.313,0.198 10 false *1 2.927,0.76 3.24,0.958 0.313,0.198 10 false *h
*A Pressing Forward *B Pulling
*1 Black Out Tape - -
*a Correct *b Incorrect
*c Squeegee *d Release Paper
*e Hem *f Corner
*g Heat Light *h 20 to 30°C (68 to 86°F)
*i 40 to 50° (for pressing forward) *j 30 to 45° (for pulling)
*k 30 to 70 mm/sec. (1.19 to 2.75 in./sec.) *l 10 to 20 mm (0.394 to 0.787 in.)


i.

Clean the vehicle body surface

1. Using a heat light, heat the vehicle body surface.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


2. Wipe off any tape adhesive residue with cleaner.


ii.

Installation temperature

1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 to 30°C (68 to 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 to 30°C (68 to 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape becomes stiff and comes off easily. When the temperature is high, the tape elasticity increases.




iii.

Before installation

1. Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.



iv.

Key points for handling the tape

1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

NOTICE:

Do not bend the tape or leave it in high temperature places.



v.

Key points for installation of the tape (How to use a squeegee and installation procedure for flat surfaces)

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body prematurely. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 30 to 70 mm (1.19 to 2.75 in.) per second.

NOTICE:
·

Position the tape accurately to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms after removal.

·

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.



HINT:
·

Either angle of the squeegee (pressing forward or pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.




vi.

Key points for installation of the tape (How to use a squeegee and installation procedure for hemmed surfaces)

1. If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.



vii.

Key points for installation of the tape (How to use a squeegee and installation procedure for corners)

1. Remove the release paper and apply the tape carefully with your fingers.

2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.


viii.

Check after installation

After completing the installation, check if the tape is installed neatly. If the tape is not installed neatly, install a new tape.

NOTICE:

Do not reuse the tape.




Hide 75986B 2.INSTALL FRONT DOOR NO. 3 STRIPE LH

a.
B599575C01
3.521,1.313 3.656,1.094 false 4.583,0.958 4.781,0.875 false 6.875,3.698 7,3.698 7,3.698 7,4.146 false 5.542,2.833 5.781,2.635 true 4.01,0.208 4.385,0.448 0.375,0.24 12 false *A 4.531,0.208 4.906,0.448 0.375,0.24 12 false *B 3.635,0.927 3.823,1.135 0.188,0.208 10 true *a 0.385,2.75 0.49,2.917 0.104,0.167 10 true a 0.688,2.677 0.844,2.875 0.156,0.198 10 false a 0.552,3.729 0.729,3.906 0.177,0.177 10 true b 1.01,3.531 1.167,3.729 0.156,0.198 10 true b 4.896,5.635 5.385,5.823 0.49,0.188 10 false a - a 4.479,3.844 4.958,4 0.479,0.156 10 false b - b 1.854,0.875 2.01,1.073 0.156,0.198 10 false A 1.969,5.208 2.115,5.375 0.146,0.167 10 true B 3.917,2.688 4.073,2.854 0.156,0.167 10 false C 5.948,2.813 6.104,2.979 0.156,0.167 10 false D 4.198,5.25 4.354,5.417 0.156,0.167 10 false E 6.49,4.333 6.646,4.5 0.156,0.167 10 false F 4.042,2.885 4.229,3.094 0.188,0.208 10 true *c 5.781,2.521 5.969,2.688 0.188,0.167 10 false *b 2.198,5.292 2.385,5.5 0.188,0.208 10 true *c 6.927,4.188 7.073,4.344 0.146,0.156 10 false *b 4.76,0.75 4.948,0.958 0.188,0.208 10 true *a 1.771,1.198 1.958,1.406 0.188,0.208 10 true *d 0.042,0.021 0.354,0.177 0.313,0.156 10 false *e
*A for RH Side *B for LH Side
*a Point A *b Point B
*c Dimensions to Overlap with Front Door Weatherstrip LH *d Dimensions to Overlap with Upper Door Frame Garnish LH
*e Reference - -


Standard Measurement
Area Dimensions Area Dimensions
A 8.8 mm (0.346 in.) B 3.4 mm (0.134 in.)
C 4.1 mm (0.161 in.) D -1.0 to 1.0 mm (-0.0394 to 0.0394 in.)
E 1.2 mm (0.0472 in.) F 1.2 mm (0.0472 in.)


Hide 75966B 3.INSTALL FRONT DOOR NO. 4 STRIPE LH

a.
B599577C01
3.365,1.438 3.115,1.25 false 3.979,1.417 3.656,1.49 false 6.052,0.896 6.448,1.01 true 5.917,1.25 6.302,1.25 false 4.833,4.313 5.333,4.167 true 5.635,4.938 5.698,5.115 true 4.021,0.208 4.396,0.448 0.375,0.24 12 false *A 4.542,0.208 4.917,0.448 0.375,0.24 12 false *B 3.448,1.469 3.76,1.667 0.313,0.198 10 false *a 5.156,4.49 5.771,4.688 0.615,0.198 10 false a - a 2.906,2.521 3.063,2.719 0.156,0.198 10 false a 2.75,2.885 2.906,3.083 0.156,0.198 10 false a 6.333,1.167 6.51,1.344 0.177,0.177 10 true *b 6.49,0.927 6.896,1.094 0.406,0.167 10 true *b, *e 1.573,0.531 1.76,0.688 0.188,0.156 10 true *d 1.938,4.958 2.135,5.135 0.198,0.177 10 true *c 1.365,0.531 1.479,0.688 0.115,0.156 10 true A 2.094,5.104 2.208,5.24 0.115,0.135 10 true B 4.667,3.667 4.792,3.833 0.125,0.167 10 false D 5.354,5.313 5.479,5.479 0.125,0.167 10 false E 5.521,4.781 5.833,4.979 0.313,0.198 10 false *e 2,5.448 2.125,5.615 0.125,0.167 10 true C 4.625,4.271 4.938,4.469 0.313,0.198 10 false *e 0.052,0.042 0.365,0.24 0.313,0.198 10 false *f
*A for RH Side *B for LH Side
*a Point A *b Point B
*c Dimensions to Overlap with Front Door Weatherstrip LH *d Dimensions to Overlap with Upper Door Frame Garnish LH
*e Edge of Curved Surface *f Reference


Standard Measurement
Area Dimensions Area Dimensions
A 21.7 mm (0.854 in.) B 5.0 mm (0.197 in.)
C 11.0 mm (0.433 in.) D 2.6 mm (0.102 in.)
E 1.0 mm (0.0394 in.) - -


Hide 67862 4.CONNECT FRONT DOOR WEATHERSTRIP LH

Hide 67664 5.INSTALL UPPER DOOR FRAME GARNISH LH

Hide 68151C 6.INSTALL FRONT DOOR GLASS RUN LH

Hide 68102 7.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

Z101186

Click here(Click here)

Hide 8.INSTALL HOLE PLUG

Hide 67832 9.INSTALL FRONT DOOR SERVICE HOLE COVER LH

Hide 68193C 10.INSTALL FRONT DOOR FRONT BELT SEAL LH

Hide 68172A 11.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

Hide 67492A 12.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

Hide 67602 13.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 14.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 15.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 69284C 16.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 17.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 18. INITIALIZATION POWER WINDOW CONTROL SYSTEM

Hide 19.CHECK POWER WINDOW OPERATION

Z101186

Click here(Click here)

Hide 20. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART