|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Adhesive 1324 | ★ | Precoated part |
| *A | for Front Passenger Side | *B | for Driver Side |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
MP grease | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
MP grease |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 30 | SIDE AIR BAG PRESSURE SENSOR ASSEMBLY | 8983AA | - | - | - |
| 31 | FRONT DOOR SERVICE HOLE COVER | 67832 | - | - | - |
| 32 | OUTER REAR VIEW MIRROR ASSEMBLY | 87940 | - | - | - |
| 33 | FRONT DOOR NO. 2 SERVICE HOLE COVER | 67834 | - | - | - |
| 34 | HOLE PLUG | - | - | - | - |
| 35 | MULTIPLEX NETWORK FRONT DOOR ECU | 89223 | - | - | - |
| 36 | FRONT NO. 1 SPEAKER ASSEMBLY | 86160 | - | - | - |
| 37 | FRONT DOOR BELT FRONT SEAL | 68193C | - | - | - |
| 38 | FRONT DOOR BELT REAR SEAL | 68195B | - | - | - |
| 39 | FRONT DOOR GLASS WEATHERSTRIP INNER | 68172A | - | - | - |
| 40 | FRONT DOOR LOWER FRAME BRACKET GARNISH | 67492A | - | - | - |
| *A | for Front Passenger Side | *B | for Driver Side |
| *C | w/ Seat Memory Switch | - | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
67866F
1.INSTALL FRONT DOOR NO. 3 WEATHERSTRIP
|
Install in this Direction | - | - |
Remove the clips from a new No. 3 front door weatherstrip.
Clean the surface of the front door.
Remove any remaining double-sided tape from the front door.
Wipe off any adhesive residue with cleaner.
Using a heat light, heat a new No. 1 luggage compartment upper cover and the front door surface.
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
| Part | Temperature |
|---|---|
| Front door No. 3 weatherstrip | 20 to 30°C (68 to 86°F) |
Remove the peeling paper from the face of the No. 3 front door weatherstrip.
Attach the clip and install the No. 1 luggage compartment upper cover as shown in the illustration.
75986B
3.INSTALL FRONT DOOR NO. 3 STRIPE
67001A
4.INSTALL FRONT DOOR PANEL CUSHION
67864B
5.INSTALL FRONT DOOR NO. 2 WEATHERSTRIP
67496C
7.INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER
67862
10.INSTALL FRONT DOOR WEATHERSTRIP
Clean the front door panel surface.
1. Remove the double-sided tape from the front door weatherstrip and front door panel.
2. Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the front door panel and front door weather strip.
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| Front Door Weatherstrip | 20 to 30°C (68 to 86°F) |
Remove the peeling paper from the front door weatherstrip.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Engage the clips and install the front door weatherstrip with the double-sided tape.
67664
11.INSTALL UPPER DOOR FRAME GARNISH
68610
12.INSTALL FRONT DOOR CHECK ASSEMBLY
|
Nut |
|
Bolt |
When reusing a bolt:
1. Clean the threads of the bolt.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
Install the front door check assembly with the 2 nuts and bolt.
69318C
13.INSTALL DOOR LOCK WIRING HARNESS SEAL
69750E
14.INSTALL LOCK / UNLOCK KNOB FRONT DOOR INSIDE LOCKING CABLE
69710D
15.INSTALL OPEN LEVER FRONT DOOR LOCK REMOTE CONTROL CABLE
69036A
16.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY
69202A
19.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.
Engage the guides to install the front door outside handle frame sub-assembly as shown in the illustration.
Engage the clamp to install the wire harness.
Using a T30 "TORX" socket wrench, tighten the screw.
Engage the snap and install the front door lock open rod LH as shown in the illustration.
69241H
20.INSTALL FRONT DOOR OUTSIDE HANDLE PAD FRONT
69242E
21.INSTALL FRONT DOOR OUTSIDE HANDLE PAD REAR
69510
22.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Using a T30 "TORX" socket wrench, tighten the screw.
Install the hole plug.
69217D
23.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Using a T30 "TORX" socket wrench, tighten the screw.
Install the hole plug.
69210
24.INSTALL FRONT DOOR HANDLE OUTSIDE ASSEMBLY
69802
25.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
|
Nut |
|
Connector |
Apply MP grease to the sliding parts of the front door window regulator assembly.
Install the front door window regulator assembly with the 7 nuts.
Connect the connector.
67402F
26.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
67404F
27.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
68151C
28.INSTALL FRONT DOOR GLASS RUN
68102
29.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
Connect the multiplex network door computer FR RH.
For Driver Side:
1. Connect the multiplex network master switch assembly.
For Front Passenger Side:
1. Connect the power window regulator switch assembly.
Connect the connectors to install the front door trim board sub-assembly LH.
Connect the cable to the negative (-) battery terminal and turn the ignition switch on.
Move the front door glass sub-assembly so that the door glass bolt holes can be seen turn the ignition switch off.
Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.
Be careful not to damage the front door glass sub-assembly.
Install the front door glass sub-assembly with the 2 bolts.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an SRS part is accidentally deployed, it may cause a serious injury.
Disconnect the connectors to remove the front door trim board sub-assembly.
For Driver Side:
1. Disconnect the multiplex network master switch assembly
For Front Passenger Side:
1. Disconnect the power window regulator switch assembly.
Disconnect the multiplex network door computer FR RH.
67832
31.INSTALL FRONT DOOR SERVICE HOLE COVER
67834
33.INSTALL FRONT DOOR NO. 2 SERVICE HOLE COVER
34.INSTALL HOLE PLUG
89223
35.INSTALL MULTIPLEX NETWORK FRONT DOOR ECU
68193C
37.INSTALL FRONT DOOR BELT FRONT SEAL
68195B
38.INSTALL FRONT DOOR BELT REAR SEAL
68172A
39.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP
67492A
40.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH
69206B
41.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
81080V
42.INSTALL NO.2 INTERIOR ILLUMINATION LIGHT ASSEMBLY
84927C
43.INSTALL SEAT MEMORY SWITCH LH
81230
44.INSTALL COURTESY LIGHT ASSEMBLY
67602
45.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
46.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
47.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
69284C
48.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
49.INSPECT FITTING OF FRONT DOOR
50.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
51. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
52.CHECK SRS WARNING LIGHT
53.INSPECT DOOR LOCK OPERATION
54. PERFORM DIAGNOSTIC SYSTEM CHECK
55.INITIALIZE POWER WINDOW CONTROL SYSTEM
56.CHECK POWER WINDOW CONTROL SYSTEM
57. CHECK POWER DOOR LOCK CONTROL SYSTEM
58.INSPECT OUTER REAR VIEW MIRROR OPERATION