Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  P1C7C49  Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure  


DESCRIPTION

This DTC is stored if there is insulation malfunction in the high-voltage circuit in the air conditioning system. Possible causes are poor insulation in the compressor with motor assembly, or mixing of any oil other than ND-OIL 11 in the refrigerant cycle.

A high-voltage motor is built into the compressor with motor assembly and is cooled directly with refrigerant. Compressor oil (ND-OIL 11) with high insulation performance is used because a leakage of electrical power may occur if regular compressor oil (ND-OIL 8) is used.

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure High voltage system insulation malfunction
·

Compressor oil

·

Refrigerant pipe line

·

Compressor with motor assembly

·

CAN communication system


Memorized EV B

WIRING DIAGRAM

E414323E05
3.51,0.781 4.125,0.979 0.615,0.198 10 false LIN3 3.219,0.615 3.833,0.813 0.615,0.198 10 false 13 3.427,1.281 4.042,1.479 0.615,0.198 10 false A17 3.448,1.458 4.552,1.667 1.104,0.208 10 false EV Control ECU 3.198,2.188 4.323,2.406 1.125,0.219 10 false from IG1 Relay 5.5,1.302 7.083,1.698 1.583,0.396 10 false Air Conditioning Amplifier Assembly 1.958,2.344 3.083,2.563 1.125,0.219 10 false R/B-IG1 NO.2 1.542,0.792 2.156,0.99 0.615,0.198 10 false B23 1.625,0.563 2.24,0.76 0.615,0.198 10 false 3 1.552,2.208 2.167,2.406 0.615,0.198 10 false B23 1.615,1.979 2.229,2.177 0.615,0.198 10 false 1 1.552,2.615 2.167,2.813 0.615,0.198 10 false D20 1.625,2.427 2.24,2.625 0.615,0.198 10 false 2 1.583,3.031 2.198,3.229 0.615,0.198 10 false b3 1.635,2.823 2.25,3.021 0.615,0.198 10 false 2 1.615,3.865 2.229,4.063 0.615,0.198 10 false b3 1.625,3.656 2.24,3.854 0.615,0.198 10 false 1 1.031,0.802 1.646,1 0.615,0.198 10 false DOUT 1.177,2.198 1.792,2.396 0.615,0.198 10 false IG1 1.104,2.625 1.719,2.823 0.615,0.198 10 false GND 1.281,3.052 1.896,3.25 0.615,0.198 10 false P 1.281,3.865 1.896,4.063 0.615,0.198 10 false N 5.135,3.719 5.75,3.917 0.615,0.198 10 false N 5.135,2.885 5.75,3.083 0.615,0.198 10 false P 0.313,4.729 1.427,5.115 1.115,0.385 10 false Compressor with Motor Assembly 2.5,4.698 4.458,4.885 1.958,0.188 10 false No. 1 EV Battery Pack Wire 4.958,4.885 7.031,5.146 2.073,0.26 10 false Inverter with Converter Assembly 4.948,4.719 6.917,4.979 1.969,0.26 10 false b4 0.76,5.406 2.99,5.604 2.229,0.198 10 false : CAN Communication Line 0.76,5.865 2.99,6.063 2.229,0.198 10 false : LIN Communication Line 0.771,6.333 3,6.531 2.229,0.198 10 false : High Voltage Line 3.229,3.542 3.844,3.74 0.615,0.198 10 false * 3.25,4.385 3.865,4.583 0.615,0.198 10 false * 2.792,5.385 3.781,5.583 0.99,0.198 10 false *: Shielded 4.938,2.885 5.552,3.083 0.615,0.198 10 false 2 4.927,3.719 5.542,3.917 0.615,0.198 10 false 1

CAUTION / NOTICE / HINT

CAUTION:
·

After removing the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

·

After removing the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Electrical insulation performance may decrease significantly if even a small amount of oil other than ND-OIL 11 is used (or enters) in the refrigerant cycle, causing a DTC to be output.

·

If other oil is accidentally used and a DTC is output, collect as much oil in the refrigerant cycle into the compressor with motor assembly as possible and replace it with ND-OIL 11 to increase the ND-OIL 11 ratio amount.

·

Replace the main components of the air conditioning cycle (evaporator, condenser, and compressor) if a large amount of oil other than ND-OIL 11 enters the system. Failing to do so may cause electrical insulation performance to remain low, causing a DTC to be output.

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.



HINT:

If it can be confirmed that any compressor oil other than ND-OIL 11 has been used in the vehicle, replace the main components of the air conditioning cycle.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

HINT:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK COMPRESSOR OIL

B

2.CHECK COMPRESSOR OIL
a.

Check that no types of compressor oil other than ND-OIL 11 (such as ND-OIL 8, etc.) were used in the past.

HINT:
·

Electrical insulation performance may decrease significantly if even a small amount of oil other than ND-OIL 11 is used (or enters) in the refrigerant cycle, causing a DTC to be output.

·

Replace the main components of the refrigerant cycle (evaporator, condenser, and compressor) if a large amount of oil other than ND-OIL 11 enters the system. Failing to do so may cause electrical insulation performance to remain low, causing a DTC to be stored.




Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPLACE MAIN COMPONENTS OF REFRIGERANT CYCLE

3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > EV > Trouble Codes
50001 397

Result:
Proceed to
NEXT



NEXT

4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Because the compressor with motor assembly has a high-voltage circuit, wear insulated gloves and pull out the service plug grip to cut off the high-voltage circuit before inspection.


Pre-procedure1

a.

Turn the ignition switch to ON (READY).


b.

Prepare the vehicle according to the table below for 3 minutes.

Item Condition
Blower speed HI
Temperature setting MAX COLD
A/C switch On


c.

Turn the ignition switch off.


d.

Remove the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL



CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the ignition switch ON (READY) may cause a malfunction. Do not turn the ignition switch to ON (READY) with the service plug grip removed.


e.
E437396C05
1.531,0.25 1.948,0.5 0.417,0.25 2.333,1.583 2.083,1.583 2.083,1.583 1.917,1.177 true 2.396,1.51 2.646,1.729 0.25,0.219 10 false N 0.271,0.219 0.583,0.417 0.313,0.198 10 false *a 1.667,0.313 1.979,0.51 0.313,0.198 10 false b3
*a Component without harness connected
(Compressor with Motor Assembly)


Disconnect the b3 compressor with motor assembly connector.


Procedure1

f.

Using a megohmmeter, measure the resistance according to the value(s) in the table below.

Standard Resistance:
for AWD:
Tester Connection Condition Specified Condition

Click Location & Routing(b3)Location & Routing

Click Connector(b3)Engine Compartment>FC Cooling Water Pump Cable>Compressor with Motor Assembly

b3-1 (N) - Body ground Always 3 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

g.

None



OK

5.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

5.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Because the compressor with motor assembly has a high-voltage circuit, wear insulated gloves and pull out the service plug grip to cut off the high-voltage circuit before inspection.


Pre-procedure1

a.

Turn the ignition switch to ON (READY).


b.

Prepare the vehicle according to the table below for 3 minutes.

Item Condition
Blower speed HI
Temperature setting MAX COLD
A/C switch On


c.

Turn the ignition switch off.


d.

Remove the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL



CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the ignition switch to ON (READY) with the service plug grip removed.


e.
E437396C06
1.531,0.25 1.948,0.5 0.417,0.25 1.167,1.583 1.417,1.583 1.417,1.583 1.563,1.219 true 1.052,1.5 1.385,1.698 0.333,0.198 10 false P 0.271,0.219 0.583,0.417 0.313,0.198 10 false *a 1.677,0.313 1.99,0.51 0.313,0.198 10 false b3
*a Component without harness connected
(Compressor with Motor Assembly)


Disconnect the b3 compressor with motor assembly connector.


Procedure1

f.

Using a megohmmeter, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b3)Location & Routing

Click Connector(b3)Engine Compartment>FC Cooling Water Pump Cable>Compressor with Motor Assembly

b3-2 (P) - Body ground Always 3 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

g.

None



OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPLACE AIR CONDITIONING CYCLE