Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0448330 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E456050N01
6.375,0.25 6.844,0.25 false 1.563,0.302 2.031,0.302 false 0.604,2.073 0.865,2.073 0.865,2.073 1.115,1.677 false 2.979,2.135 2.698,2.135 2.698,2.135 2.521,1.781 false 0.396,0.198 0.708,0.396 0.313,0.198 10 false x 6 1.875,0.844 2.188,1.042 0.313,0.198 10 false x 6 3.583,0.667 3.896,0.865 0.313,0.198 10 false x 6 2.104,0.156 2.385,0.51 0.281,0.354 18 false 2 3.052,1.969 3.333,2.323 0.281,0.354 18 false 1 0.427,1.917 0.708,2.271 0.281,0.354 18 false 3 6.208,0.104 6.49,0.458 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 UPPER RADIATOR SUPPORT SEAL 53292A - - -
2 RADIATOR COVER PLATE 53291B - - -
3 LOWER RADIATOR AIR DEFLECTOR 53295 - - -
4 REFRIGERANT FROM REFRIGERATION SYSTEM - (Click here) - -

E458063N05
1.698,0.813 2.146,0.813 false 1.49,0.667 1.865,1.104 0.375,0.438 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

5 SERVICE PLUG GRIP G3834 - - -

E458104N02
5.104,1.542 6.177,1.771 1.073,0.229 2.635,0.771 3.385,0.771 false 4.885,2.563 5.396,2.563 false 6.552,0.229 6.844,0.229 false 4.552,2.073 4.552,1.656 4.552,1.656 5.094,1.656 false 4.865,2.052 4.865,1.667 false 2.76,4.208 4.208,4.208 4.208,4.208 4.896,4.844 true 2.583,4.052 2.865,4.406 0.281,0.354 18 false 7 3.469,0.635 3.75,0.99 0.281,0.354 18 false 6 6.375,0.083 6.656,0.438 0.281,0.354 18 false 9 5.719,2.406 6.427,2.823 0.708,0.417 18 false 8, 10 5.521,3.115 5.802,3.469 0.281,0.354 10 false x 2 5.177,1.573 6.156,1.771 0.979,0.198 8 false 8.0 (82, 71 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

6 FC STACK COVER SUB-ASSEMBLY 1A906 - - -
7 FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) G9200A (Click here) - -
8 REMOVE CONNECTOR COVER ASSEMBLY - (Click here) - -
9 TERMINAL VOLTAGE - (Click here) - -
10 INSTALL CONNECTOR COVER ASSEMBLY - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

E458061N03
1.313,1.604 1.865,1.604 false 1.167,2.708 1.604,2.708 false 3.302,1.958 3.573,1.958 false 3.698,3.167 4.063,3.167 4.063,3.167 4.198,2.958 false 6.208,2.521 6.406,2.375 6.406,2.375 6.615,2.375 false 2.115,2.146 2.115,1.906 false 6.344,3.438 6.344,3.198 false 1.99,2.979 1.99,2.74 false 2.188,3.5 2.49,3.5 2.49,3.5 2.594,3.365 false 2.521,0.948 2.792,0.948 false 6.271,3.417 6.552,3.615 0.281,0.198 10 false ●★ 5.656,3.281 5.969,3.479 0.313,0.198 10 false x 3 6.458,3.052 6.771,3.25 0.313,0.198 10 false x 7 4.5,3.354 4.813,3.552 0.313,0.198 10 false x 12 2.281,0.385 2.594,0.583 0.313,0.198 10 false x 2 3.135,2.552 3.448,2.75 0.313,0.198 10 false x 2 2.531,1.656 2.844,1.854 0.313,0.198 10 false x 2 2.802,2.677 3.115,2.875 0.313,0.198 10 false x 2 2.083,2.125 2.24,2.323 0.156,0.198 10 false ● 1.948,2.969 2.104,3.167 0.156,0.198 10 false ● 3.396,3.01 3.833,3.292 0.438,0.281 18 false 11 6.656,2.208 7.094,2.49 0.438,0.281 18 false 12 1.875,3.333 2.313,3.615 0.438,0.281 18 false 13 0.875,2.563 1.313,2.844 0.438,0.281 18 false 14 1.021,1.448 1.458,1.729 0.438,0.281 18 false 15 3.865,1.802 4.302,2.083 0.438,0.281 18 false 16 2.229,0.802 2.667,1.083 0.438,0.281 18 false 17

Procedure Part Name Code
Z101186

Z101188

Z101187

11 FRONT COMPARTMENT UNDER COVER 51441N - - -
12 FRONT LOWER SUSPENSION MEMBER PROTECTOR 51219 - - -
13 NO. 15 FC INVERTER COOLING HOSE G91CF - - -
14 NO. 1 DISCHARGE HOSE SUB-ASSEMBLY 88703A (Click here) - -
15 SUCTION HOSE SUB-ASSEMBLY A 88704A (Click here) - -
16 COMPRESSOR WITH MOTOR ASSEMBLY 88370 (Click here) - -
17 NO. 2 FC COOLING WATER PUMP CABLE BRACKET 16A1BB - - -

● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the compressor with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 53292A 1.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 53291B 2.REMOVE RADIATOR COVER PLATE

Hide 53295 3.REMOVE LOWER RADIATOR AIR DEFLECTOR

Hide 4.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 1A906 6.REMOVE FC STACK COVER SUB-ASSEMBLY

Hide G9200A 7.DISCONNECT FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY)

Z101186

Click here(Click here)

Hide 8.REMOVE CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 9.CHECK TERMINAL VOLTAGE

Z101186

Click here(Click here)

Hide 10.INSTALL CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 51441N 11.REMOVE FRONT COMPARTMENT UNDER COVER

Hide 51219 12.REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR

Hide G91CF 13.DISCONNECT NO. 15 FC INVERTER COOLING HOSE

a.
E450306


Hide 88703A 14.DISCONNECT NO. 1 DISCHARGE HOSE SUB-ASSEMBLY

a.
E450307C01
1.458,1.271 1.594,1.552 0.135,0.281 18 true i 4.271,0.094 4.552,0.448 0.281,0.354 18 false iii 1.615,1.542 1.844,1.708 0.229,0.167 10 true *a 2.521,0.656 2.75,0.823 0.229,0.167 10 true *b 2.302,0.854 2.458,1.146 0.156,0.292 18 true ii
*a Bolt (A) *b Bolt (B)


i.

Remove the bolt (A).


ii.

Remove the bolt (B) and disconnect the No. 1 discharge hose sub-assembly.


iii.

Remove the O-ring from the No. 1 discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.




Hide 88704A 15.REMOVE SUCTION HOSE SUB-ASSEMBLY A

a.
E450308N01
0.448,0.115 0.729,0.469 0.281,0.354 18 false i 4.365,0.115 4.646,0.469 0.281,0.354 18 false ii

i.

Remove the bolt (B) and disconnect the suction hose sub-assembly A.


ii.

Remove the O-ring from the suction hose sub-assembly A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.




Hide 88370 16.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

a.
E456051N01
0.271,0.135 0.552,0.49 0.281,0.354 18 false i

i.

Detach the clamp.



b.
E456052N01
0.563,0.094 0.74,0.385 0.177,0.292 18 true i 4.333,0.125 4.51,0.417 0.177,0.292 18 true ii

i.

Remove the 2 bolts and 2 nuts.


ii.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.



c.
E456053C01
1.719,1.198 2,0.833 2,0.833 2.167,0.833 true 1.083,0.51 1.365,0.865 0.281,0.354 18 false i 5.24,0.813 5.417,1.104 0.177,0.292 18 true ii 4.99,1.063 5.198,1.25 0.208,0.188 10 true *b 4.469,1.146 4.646,1.323 0.177,0.177 10 true *a 2.208,0.729 2.385,0.906 0.177,0.177 10 false *c
*a Connector (A) *b Connector (B)
*c Green-colored Lock - -
V113147

Slide - -


i.

While holding the compressor with motor assembly, slide the green-colored lock of the connector (A) as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulating gloves.


NOTICE:

Insulate the disconnected terminals and connector with vinyl tape.



ii.

Disconnect the connector (B) and remove the compressor with motor assembly.



Hide 16A1BB 17.REMOVE NO. 2 FC COOLING WATER PUMP CABLE BRACKET

a.
E450312