Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D8387  Lost Communication with Hydrogen Pump Inverter Missing Message  


DESCRIPTION

The EV control ECU detects serial communication malfunctions with the FC hydrogen pump inverter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D8387 Lost Communication with Hydrogen Pump Inverter Missing Message When hydrogen pump LIN communication control is ON, there is a communication stop between the EV control ECU and hydrogen pump inverter for 1.5 seconds or more continuously.
(1 trip detection logic)
·

FC hydrogen pump inverter assembly

·

EV control ECU

·

IGCT NO. 2 relay

·

Wire harness or connector


Master Warning: Comes on EV A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - ○ ○ ○ ○ -

HINT:

By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1D8387 -

WIRING DIAGRAM

A480725E03
0.563,2.792 1.865,3.094 1.302,0.302 10 false Auxiliary Battery 0.385,2.042 1.302,2.24 0.917,0.198 10 false R/B RR# 2 0.354,1.406 1.271,1.604 0.917,0.198 10 false IGCT NO. 2 1.063,1.052 1.979,1.25 0.917,0.198 10 false IGCT NO. 2 3.042,2.01 3.583,2.26 0.542,0.25 10 false MREL 2.219,1.99 2.76,2.24 0.542,0.25 10 false A8*1 2.281,1.792 2.823,2.042 0.542,0.25 10 false 21 3.219,3.167 4.854,3.354 1.635,0.188 10 false EV Control ECU 4.094,1.219 4.458,1.469 0.365,0.25 10 false LIN1 4.49,1.333 5.031,1.583 0.542,0.25 10 false A15 4.552,1.135 5.094,1.385 0.542,0.25 10 false 9 5.469,2.417 6.719,2.927 1.25,0.51 10 false FC Hydrogen Pump Inverter Assembly 5.49,3.167 7.01,3.448 1.521,0.281 10 false FC Converter Assembly 5.448,1.354 5.813,1.604 0.365,0.25 10 false HLIN 5.448,0.385 5.813,0.635 0.365,0.25 10 false H+B1 5.458,2.01 6.031,2.208 0.573,0.198 10 false HGND 5.458,2.271 6,2.521 0.542,0.25 10 false B3 0.99,0.281 1.156,0.469 0.167,0.188 10 false 3 1.781,0.281 1.948,0.469 0.167,0.188 10 false 5 1.781,0.635 1.948,0.823 0.167,0.188 10 false 2 0.99,0.625 1.156,0.813 0.167,0.188 10 false 1 5.26,0.271 5.427,0.458 0.167,0.188 10 false 1 5.26,1.865 5.427,2.052 0.167,0.188 10 false 2 5.24,1.24 5.406,1.427 0.167,0.188 10 false 3 4.49,1.698 5.031,1.948 0.542,0.25 10 false A15 4.521,1.531 5.063,1.781 0.542,0.25 10 false 10 3.99,1.708 4.99,2.156 1,0.448 10 false DRN7 2.813,0.563 3.729,0.76 0.917,0.198 10 false IGCT NO. 9 4.01,0.563 4.927,0.76 0.917,0.198 10 false FC IGCT 2.594,1.99 3.135,2.24 0.542,0.25 10 false D15*2 2.719,1.792 3.26,2.042 0.542,0.25 10 false 21 1.833,2.99 2.792,3.188 0.958,0.198 10 false *1: for LHD 1.833,3.281 2.792,3.479 0.958,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Working Mode" is Startup or Working. Then, wait for 2 minutes or more.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FC HYDROGEN PUMP INVERTER ASSEMBLY)

Pre-procedure1

a.
A479002

Disconnect the FC hydrogen pump inverter assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B3)Location & Routing

Click Connector(B3)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

B3-1 (H+B1) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC hydrogen pump inverter assembly connector.



OK

2.CHECK HARNESS AND CONNECTOR (FC HYDROGEN PUMP INVERTER ASSEMBLY - BODY GROUND)

NG

8.CHECK HARNESS AND CONNECTOR (FC HYDROGEN PUMP INVERTER ASSEMBLY - IGCT NO. 2 RELAY)
2.CHECK HARNESS AND CONNECTOR (FC HYDROGEN PUMP INVERTER ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the FC hydrogen pump inverter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B3)Location & Routing

Click Connector(B3)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

B3-2 (HGND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC hydrogen pump inverter assembly connector.



OK

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC HYDROGEN PUMP INVERTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC HYDROGEN PUMP INVERTER ASSEMBLY)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the FC hydrogen pump inverter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A15,B3)Location & Routing

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B3)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

A15-9 (LIN1) - B3-3 (HLIN) Always Below 1 Ω
A15-9 (LIN1) or B3-3 (HLIN) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC hydrogen pump inverter assembly connector.


b.

Reconnect the EV control ECU connector.



OK

4.REPLACE FC HYDROGEN PUMP INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE FC HYDROGEN PUMP INVERTER ASSEMBLY
HINT:

Replace both the FC cooling water pump inverter assembly and FC hydrogen pump inverter assembly at the same time

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

6.SIMULATION TEST
6.SIMULATION TEST
a.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Startup or Working. Then, wait for 2 minutes or more.

Powertrain > EV > Data List
Tester Display
FC Work Mode
50003 397 962

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1D8387 is output A
DTCs are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

B

END

8.CHECK HARNESS AND CONNECTOR (FC HYDROGEN PUMP INVERTER ASSEMBLY - IGCT NO. 2 RELAY)

Pre-procedure1

a.

Disconnect the FC hydrogen pump inverter assembly connector.


b.

Remove the IGCT NO. 2 relay from the No. 1 front compartment relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B3)Location & Routing

Click Connector(B3)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

B3-1 (H+B1) - 5 (IGCT NO. 2 relay holder) Always Below 1 Ω
B3-1 (H+B1) or 5 (IGCT NO. 2 relay holder) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reinstall the IGCT NO. 2 relay.


b.

Reconnect the FC hydrogen pump inverter assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR