Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DB01C  High-Range Hydrogen Pressure Sensor Circuit Voltage Out of Range  


DESCRIPTION

The hydrogen system of the FC system feeds the FC stack with hydrogen, so that the FC stack can generate power. The hydrogen tank pressure sensor measures hydrogen pressure in the high-range pressure area including the hydrogen tank, and it transmits measured values to the meter as the remaining amount of hydrogen.

When hydrogen is filled at a hydrogen station, the maximum output value of the hydrogen tank pressure sensor (for Inlet Side) during filling is stored. When the FC system is started next time, if the hydrogen tank pressure sensor (for Outlet Side) value when the tank shut valve is opened and the pressure value stored at the time of filling completion deviate by a specified value or more, the DTC is stored as a characteristic abnormality.

A459252C02
6.375,2.104 6.688,2.302 0.313,0.198 10 false *1 6.469,0.927 6.781,1.125 0.313,0.198 10 false *2 4.969,0.948 5.281,1.146 0.313,0.198 10 false *3 6,4.656 6.313,4.854 0.313,0.198 10 false *4 5.104,4.656 5.417,4.854 0.313,0.198 10 false *5 4.25,4.646 4.563,4.844 0.313,0.198 10 false *6 5.938,4.042 6.25,4.24 0.313,0.198 10 false *7 5.094,4.031 5.406,4.229 0.313,0.198 10 false *8 4.208,4.042 4.521,4.24 0.313,0.198 10 false *9 5.865,2.969 6.177,3.167 0.313,0.198 10 false *10 5.042,2.979 5.354,3.177 0.313,0.198 10 false *11 4.167,2.969 4.479,3.167 0.313,0.198 10 false *12 3.438,1.49 3.75,1.698 0.313,0.208 10 false *13 2.792,1.052 3.104,1.25 0.313,0.198 10 false *14 2.396,1.708 2.708,1.906 0.313,0.198 10 false *15 1.958,2.281 2.271,2.479 0.313,0.198 10 false *18 0.906,2.063 1.219,2.26 0.313,0.198 10 false *17 1.906,3.083 2.219,3.281 0.313,0.198 10 false *19 1.5,3.625 1.813,3.823 0.313,0.198 10 false *20 0.427,3.427 0.74,3.625 0.313,0.198 10 false *21 0.958,4.458 1.271,4.656 0.313,0.198 10 false *22 2.031,1.052 2.344,1.25 0.313,0.198 10 false *23 3.063,1.052 3.375,1.25 0.313,0.198 10 false *23 4.167,3.323 4.479,3.521 0.313,0.198 10 false *24 5.042,3.323 5.354,3.521 0.313,0.198 10 false *24 5.875,3.323 6.188,3.521 0.313,0.198 10 false *24 4.167,3.51 4.479,3.708 0.313,0.198 10 false *25 5.031,3.5 5.344,3.698 0.313,0.198 10 false *25 5.896,3.479 6.208,3.677 0.313,0.198 10 false *25 3.49,0.521 3.802,0.719 0.313,0.198 10 false *e 5.177,5.979 5.49,6.177 0.313,0.198 10 false *b 0.656,5.896 0.969,6.094 0.313,0.198 10 false *c 1.344,5.885 1.656,6.083 0.313,0.198 10 false *d 1.729,1.042 2.042,1.24 0.313,0.198 10 false *16 5.156,5.615 5.469,5.813 0.313,0.198 10 false *a
*1 Hydrogen Inlet Receptacle Assembly *2 Hydrogen Tank Pressure Sensor (for Inlet Side)
*3 Hydrogen Tank Pressure Sensor (for Outlet Side) *4 No. 1 Hydrogen Tank Assembly
*5 No. 2 Hydrogen Tank Assembly *6 No. 3 Hydrogen Tank Assembly
*7 Hydrogen Tank Temperature Sensor 1 *8 Hydrogen Tank Temperature Sensor 2
*9 Hydrogen Tank Temperature Sensor 3 *10 Tank Shut Valve 1
*11 Tank Shut Valve 2 *12 Tank Shut Valve 3
*13 Hydrogen Supply Regulator Assembly *14 Hydrogen Primary Pressure Sensor
*15 Fuel Injector Assembly *16 Hydrogen Secondary Pressure Sensor
*17 FC Stack *18 Hydrogen Recirculation Pump Assembly
*19 Exhaust Drainage Valve (Hydrogen Recirculation Separator Assembly) *20 FC Air Pressure Regulator Assembly (Air Pressure Regulating Valve)
*21 FC Air Pressure Regulator Assembly (Air Sealing Valve) *22 FC Air By-pass Valve Assembly (Air Shunt Valve)
*23 Pressure Relief Valve *24 Manual Valve
*25 Pressure Relief Device - -
*a Hydrogen System *b Air System
*c From the FC Air Compressor with Motor Assembly *d To the Exhaust Drainage Pipe
*e High-range Pressure Area - -


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DB01C High-Range Hydrogen Pressure Sensor Circuit Voltage Out of Range Following diagnostic checks are conducted when the ignition switch is turned to ON (READY) the first time after filling at a hydrogen station.
If the difference between the following 2 pressure values is above a threshold, it is interpreted that a hydrogen tank pressure sensor is malfunctioning:
·

Hydrogen Filling System High Pressure after completion of hydrogen filling, which is stored in the hydrogen fuel control ECU

·

Smoothed Value of High-range Hydrogen Pressure when the ignition switch is turned to ON (READY) after filling


(3 trip detection logic)*1
·

Hydrogen tank pressure sensor (for inlet side)

·

Hydrogen tank pressure sensor (for outlet side)

·

Hydrogen fuel control transmitter

·

Hydrogen fuel control ECU assembly

·

Wire harness or connector


Master Warning: Comes on EV B

*1: Filling hydrogen and then turning the ignition switch to ON (READY) is counted as 1 trip.


Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - ○ - - - -

HINT:

By accessing the "FC Work Mode" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1DB01C
·

High-Range Hydrogen Pressure (Filtered Value)

·

Hydrogen Intake Pressure Sensor Value

·

Tank Shut Valve 1 Drive Status

·

Tank Shut Valve 2 Drive Status

·

Tank Shut Valve 3 Drive Status

·

Hydrogen Tank 1 Temperature (Filtered Value)

·

Hydrogen Tank 2 Temperature (Filtered Value)

·

Hydrogen Tank 3 Temperature (Filtered Value)

·

Hydrogen Tank 1 Temperature at Hydrogen Filling

·

Hydrogen Tank 2 Temperature at Hydrogen Filling

·

Hydrogen Tank 3 Temperature at Hydrogen Filling



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

Hydrogen filling has to be conducted 3 times, so do not fill the tank full at the 1st or 2nd filling.

1.

Open the fuel lid, and fill the tank at a hydrogen station.

2.

Close the fuel lid.

3.

Turn the ignition switch to ON (READY) and wait for 1 minute or more.

HINT:

The "High-Range Hydrogen Pressure (Filtered Value)" and "Hydrogen Intake Pressure Sensor Value" of the Data List will be almost the same values.


4.

Turn the ignition switch off and wait for 10 minutes or more.

5.

Open the fuel lid, and fill the tank at a hydrogen station.

6.

Close the fuel lid.

7.

Turn the ignition switch to ON (READY) and wait for 1 minute or more.

8.

Turn the ignition switch off and wait for 10 minutes or more.

9.

Open the fuel lid, and fill the tank at a hydrogen station.

10.

Close the fuel lid.

11.

Turn the ignition switch to ON (READY) and wait for 1 minute or more.



PROCEDURE

1.CHECK DTC OUTPUT
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

According to the display on the GTS, check for DTCs in the Health Check.


Result:
Result Proceed to
Only P1DB01C is output A
P1DB01C is output and DTCs other than the DTCs in the table below are output B
P1DB01C is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1DFA11 (Hydrogen Filling Control) Hydrogen Intake Pressure Sensor Circuit Short to Ground
P1DFA15 (Hydrogen Filling Control) Hydrogen Intake Pressure Sensor Circuit Short to Battery or Open
P1E0012 (Hydrogen Filling Control) Tank Shut Valve 1 Circuit Short to Battery
P1E0014 (Hydrogen Filling Control) Tank Shut Valve 1 Circuit Short to Ground or Open
P1E1012 (Hydrogen Filling Control) Tank Shut Valve 2 Circuit Short to Battery
P1E1014 (Hydrogen Filling Control) Tank Shut Valve 2 Circuit Short to Ground or Open
P1E5A12 (Hydrogen Filling Control) Tank Shut Valve 3 Circuit Short to Battery
P1E5A14 (Hydrogen Filling Control) Tank Shut Valve 3 Circuit Short to Ground or Open
P1E1996 (Hydrogen Filling Control) Infrared Transmitter Component Internal Failure
System malfunction P1DE51C (EV) Hydrogen Tank 1 Temperature Sensor Circuit Voltage Out of Range
P1DEA1C (EV) Hydrogen Tank 2 Temperature Sensor Circuit Voltage Out of Range
P1E4A1C (EV) Hydrogen Tank 3 Temperature Sensor Circuit Voltage Out of Range
P1E367E (EV) Tank Shut Valve 1 Actuator Stuck On


HINT:

DTC P1DB01C may be store due to problems that cause the DTCs shown above to be output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order of the listed DTCs shown in the table above.


Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

2.CLEAR DTC

C

GO TO DTC CHART

2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

3.CHECK DTC OUTPUT (HYDROGEN FILLING CONTROL)
3.CHECK DTC OUTPUT (HYDROGEN FILLING CONTROL)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Press the fuel lid opener switch.


c.

Fully open the fuel lid and wait for 10 seconds.


d.

With the fuel lid fully opened, turn the ignition switch to ON.


Procedure1

a.

Check for DTCs.

Powertrain > Hydrogen Filling Control > Trouble Codes
50001 494
Result:
Result Proceed to
DTCs are not output A
P1E1996 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

4.READ VALUE USING GTS (HYDROGEN INTAKE PRESSURE VALUE, HIGH-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

B

4.READ VALUE USING GTS (HYDROGEN INTAKE PRESSURE VALUE, HIGH-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

Pre-procedure1

a.

Open the fuel lid.


Procedure1

a.

Using the GTS snapshot, record the values of the Data List items listed below.

Powertrain > EV > Data List
Tester Display
Hydrogen Intake Pressure Sensor Value
High-Range Hydrogen Pressure (Filtered Value)
50003 397 809,1030

b.

Fill the tank with hydrogen.


c.

Check the recorded snapshot data.

Result:
Result Proceed to
"Hydrogen Intake Pressure Sensor Value" value in the Data List does increase during filling A
"Hydrogen Intake Pressure Sensor Value" value in the Data List does not increase during filling B


HINT:

DTCs may be output. Clear them with the GTS.



Post-procedure1

a.

Turn the ignition switch off.



A

5.READ VALUE USING GTS (HIGH-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

B

REPLACE HYDROGEN TANK TUBE JOINT ASSEMBLY (HYDROGEN TANK PRESSURE SENSOR (FOR INLET SIDE))

5.READ VALUE USING GTS (HIGH-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

Pre-procedure1

a.

None


Procedure1

a.

Turn the ignition switch to ON.


b.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
High-Range Hydrogen Pressure (Filtered Value)
50003 397 1030

c.

Turn the ignition switch to ON (READY).


Result:
Result Proceed to
When the ignition switch is turned to ON (READY) and the FC system starts, "Hydrogen Intake Pressure Sensor Value" increases. A
When the ignition switch is turned to ON (READY) and the FC system starts, "Hydrogen Intake Pressure Sensor Value" does not increase. B


Post-procedure1

a.

Turn the ignition switch off.



A

6.READ VALUE USING GTS (HYDROGEN INTAKE PRESSURE VALUE, HIGH-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

B

REPLACE HYDROGEN TANK TUBE JOINT ASSEMBLY (HYDROGEN TANK PRESSURE SENSOR (FOR OUTLET SIDE))

6.READ VALUE USING GTS (HYDROGEN INTAKE PRESSURE VALUE, HIGH-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

Pre-procedure1

a.

Remove the hydrogen tank tube joint assembly (hydrogen tank pressure sensor (for outlet side)).

HINT:

Click hereEngine / Hybrid System>FUEL>TUBE JOINT (for Outlet Side)>REMOVAL



b.

Reconnect the hydrogen tank pressure sensor (for outlet side) connector.


c.

Remove the hydrogen tank tube joint assembly (hydrogen tank pressure sensor (for inlet side)).

HINT:

Click hereEngine / Hybrid System>FUEL>TUBE JOINT (for Inlet Side)>REMOVAL



d.

Reconnect the hydrogen tank pressure sensor (for inlet side) connector.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Hydrogen Intake Pressure Sensor Value
High-Range Hydrogen Pressure (Filtered Value)
50003 397 809,1030

b.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa (15 psi).

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.1 psi). This varies by weather.




c.

Compare the "Hydrogen Intake Pressure Sensor Value" and "High-Range Hydrogen Pressure (Filtered Value)" values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Difference between "Hydrogen Intake Pressure Sensor Value" in Data List and normal atmospheric pressure value is 2450 kPa or more. A
Difference between "High-Range Hydrogen Pressure (Filtered Value)" in Data List and normal atmospheric pressure value is 2450 kPa or more. B
Other than above. C



Post-procedure1

a.

Turn the ignition switch off.


b.

Install the hydrogen tank tube joint assembly (hydrogen tank pressure sensor (for outlet side)).


c.

Install the hydrogen tank tube joint assembly (hydrogen tank pressure sensor (for inlet side)).



A

REPLACE HYDROGEN TANK TUBE JOINT ASSEMBLY (HYDROGEN TANK PRESSURE SENSOR (FOR INLET SIDE))

B

REPLACE HYDROGEN TANK TUBE JOINT ASSEMBLY (HYDROGEN TANK PRESSURE SENSOR (FOR OUTLET SIDE))

C