Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DCA31  Hydrogen Detector (Motor Room) No Signal  


DESCRIPTION

One hydrogen detector each is positioned on the upper fuel injector assembly in the front compartment, between the No. 1 hydrogen tank assembly and No. 2 hydrogen tank assembly in the under floor, and in the upper No. 3 hydrogen tank assembly, to detect hydrogen leaks from the vehicle pipe joints and output the hydrogen concentration of these to the EV control ECU.

Concentration detection begins when approximately 5 seconds have elapsed after the ignition switch is turned from off to ON. When a detected concentration is above 2%, a warning light is illuminated to indicate it to the driver, and when it is above 3%, the FC system is forced to shut down.

The sensor actuation circuit has the bridge circuit shown in the illustration below, and the detection and compensation elements are designed to be equal in resistance when they are exposed to air without hydrogen gas. As a result, RS x R1 = RR x R2 is maintained, and the bridge circuit is in equilibrium, causing a sensor output to be 0 V. However, if the detection element is exposed to air that includes hydrogen gas, it burns and the resistance will increase due to the heat, causing the bridge circuit to become unbalanced, as a result, the sensor output will also increase. This sensor output is proportional to the concentration of hydrogen gas.

A335397E02
1.469,0.385 2.427,0.75 0.958,0.365 10 false Detection element RS 3.063,0.385 3.979,0.74 0.917,0.354 10 false Compensation element RR 4.354,1 5.323,1.229 0.969,0.229 10 false Sensor output 3.052,1.417 3.667,1.615 0.615,0.198 10 false R1 2.052,1.417 2.667,1.615 0.615,0.198 10 false R2

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DCA31 Hydrogen Detector (Motor Room) No Signal All of the following conditions are met, and the output frequency of the hydrogen detector (for front compartment side) is less than 0.75 kHz and such a frequency continues for 3 seconds or more:
·

+B voltage is not low

·

2 seconds or more after starting the EV control ECU


(1 trip detection logic)
·

Hydrogen detector (for front compartment side)

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on EV A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

Related Data List
DTC No. Data List
P1DCA31 Hydrogen Detector (Motor Room) Frequency

WIRING DIAGRAM

A477028E05
4.781,2.948 5.24,3.146 0.458,0.198 10 false A16 4.771,3.115 6.125,3.448 1.354,0.333 10 false EV Control ECU 4.771,2.167 5.229,2.365 0.458,0.198 10 false EDMR 4.49,2.167 4.802,2.365 0.313,0.198 10 false 30 4.771,1.667 5.219,1.875 0.448,0.208 10 false HDMR 4.5,1.667 4.958,1.865 0.458,0.198 10 false 31 4.781,1.073 5.396,1.271 0.615,0.198 10 false VDMR 4.5,1.073 4.813,1.271 0.313,0.198 10 false 32 0.792,2.719 1.25,2.917 0.458,0.198 10 false B20 0.781,2.885 3.938,3.125 3.156,0.24 10 false Hydrogen Detector (for Front Compartment Side) 2.875,2.188 3.031,2.385 0.156,0.198 10 false 4 2.438,2.188 2.896,2.385 0.458,0.198 10 false GND 2.885,1.646 3.042,1.844 0.156,0.198 10 false 1 2.333,1.646 2.74,1.844 0.406,0.198 10 false HDMR 2.875,1.073 3.063,1.313 0.188,0.24 10 false 3 2.333,1.198 2.75,1.385 0.417,0.188 10 false VDMR 5.479,0.823 5.938,1.021 0.458,0.198 10 false 5 V 5.458,1.406 5.917,1.604 0.458,0.198 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 30 seconds or more.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HYDROGEN DETECTOR (FOR FRONT COMPARTMENT SIDE))

Pre-procedure1

a.
A476957

Disconnect the hydrogen detector (for front compartment side) connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>No. 2 Stack Wire>Hydrogen Detector (Motor Room)

B20-3 (VDMR) - B20-4 (GND) Ignition switch ON 4.8 to 5.2 V
B20-1 (HDMR) - B20-4 (GND) Ignition switch ON 4.8 to 5.2 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the hydrogen detector (for front compartment side) connector.



OK

2.REPLACE HYDROGEN DETECTOR (FOR FRONT COMPARTMENT SIDE)

NG

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - HYDROGEN DETECTOR (FOR FRONT COMPARTMENT SIDE))
2.REPLACE HYDROGEN DETECTOR (FOR FRONT COMPARTMENT SIDE)

NEXT

3.CLEAR DTC
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1DCA31 is output A
DTCs are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

B

END

5.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - HYDROGEN DETECTOR (FOR FRONT COMPARTMENT SIDE))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the hydrogen detector (for front compartment side) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,B20)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B20)Engine Compartment>No. 2 Stack Wire>Hydrogen Detector (Motor Room)

A16-32 (VDMR) - B20-3 (VDMR) Always Below 1 Ω
A16-31 (HDMR) - B20-1 (HDMR) Always Below 1 Ω
A16-30 (EDMR) - B20-4 (GND) Always Below 1 Ω
A16-32 (VDMR) or B20-3 (VDMR) - Body ground and other terminals Always 10 kΩ or higher
A16-31 (HDMR) or B20-1 (HDMR) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the hydrogen detector (for front compartment side) connector.


b.

Reconnect the EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR