Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM J

FC CONTROL  FC CONTROL SYSTEM  FC Water Release Switch Circuit  


DESCRIPTION

When the FC water release switch is operated, the drainage processing command signal is sent to the EV control ECU and FC control ECU. When conditions are met, drainage processing is performed. In addition, when the FC water release switch is operated, a drainage processing operation signal is sent to the combination meter assembly from the EV control ECU and the multi-information display is turned on.

This procedure assumes that the multi-information display will not turn on when the FC water release switch is pressed in any state other than when the ignition switch is off.

WIRING DIAGRAM

A479979E02
5.76,1.563 7,1.844 1.24,0.281 10 false FC Control ECU 0.708,4.313 2.75,4.583 2.042,0.271 10 false : CAN Communication Line 3.156,4 4.448,4.427 1.292,0.427 10 false EV Control ECU 5.302,3.656 7.115,3.938 1.813,0.281 10 false Combination Meter Assembly 0.75,2.073 2.51,2.396 1.76,0.323 10 false FC Water Release Switch 3.146,3.823 3.5,4.063 0.354,0.24 10 false A8*1 2.74,1.385 2.969,1.552 0.229,0.167 10 false 11 0.75,1.906 1.188,2.094 0.438,0.188 10 false D107 3.021,1.396 3.667,1.583 0.646,0.188 10 false WDRN 2.25,1.396 2.427,1.552 0.177,0.156 10 false 5 0.729,1.396 0.917,1.563 0.188,0.167 10 false 4 1.906,1.406 2.198,1.563 0.292,0.156 10 false SW 0.917,1.396 1.073,1.563 0.156,0.167 10 false E 3.49,0.813 3.708,0.979 0.219,0.167 10 false +B 3.521,3.833 4,4.094 0.479,0.26 10 false D15*2 0.615,3.625 1.906,4.052 1.292,0.427 10 false *1: for LHD 0.604,3.958 1.896,4.385 1.292,0.427 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
Multi-information Display On/Off Conditions
- FC Water Release Switch Multi-information Display Tester Display (EV)
FC Water Release Switch
Ignition switch off ON Off -
Ignition switch ON ON On* ON
Ignition switch ON (READY) ON On ON

*: Does not turn on for 1 second immediately after turning the ignition switch to ON.


Produced water is allowed to come out from the FC exhaust tailpipe when the FC water release switch is pressed with the following conditions met.

·

Ignition switch ON (READY)

·

The Data List that "FC Work Mode" is Working*

·

FC stack drainage conditions are met

*: When the FC water release switch is pressed with the "FC Work Mode" of the Data List in the Startup, drainage will begin after the "FC Work Mode" enters the Working.




PROCEDURE

1.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Perform the Health Check using the GTS.


b.

Check for DTCs.

Result:
Result Proceed to
DTCs are not output A
DTCs are output. B



c.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (FC WATER RELEASE SWITCH)

B

GO TO DTC CHART

2.READ VALUE USING GTS (FC WATER RELEASE SWITCH)
a.

Turn the ignition switch to ON (READY).


b.

Press the FC water release switch.


c.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
FC Water Release Switch
50003 397 1000
Result:
Result Proceed to
Data List display does change in accordance with the switch operation A
Data List display does not change in accordance with the switch operation B



d.

Turn the ignition switch off.



A

B

3.CHECK EV CONTROL ECU (FC WATER RELEASE SWITCH SIGNAL)
3.CHECK EV CONTROL ECU (FC WATER RELEASE SWITCH SIGNAL)
a.

Disconnect the FC water release switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D107)Location & Routing

Click Connector(D107)Instrument Panel>Instrument Panel Wire>FC Water Release Switch

D107-5 (SW) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Reconnect the FC water release switch connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT FC WATER RELEASE SWITCH

NG

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC WATER RELEASE SWITCH)
4.INSPECT FC WATER RELEASE SWITCH

OK

5.CHECK HARNESS AND CONNECTOR (FC WATER RELEASE SWITCH - BODY GROUND)

NG

REPLACE FC WATER RELEASE SWITCH

5.CHECK HARNESS AND CONNECTOR (FC WATER RELEASE SWITCH - BODY GROUND)
a.

Disconnect the FC water release switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D107)Location & Routing

Click Connector(D107)Instrument Panel>Instrument Panel Wire>FC Water Release Switch

D107-4 (E) - Body ground Always Below 1 Ω



c.

Reconnect the FC water release switch connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC WATER RELEASE SWITCH)
a.

Disconnect the EV control ECU connector.


b.

Disconnect the FC water release switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition

Click Location & Routing(A8,D107)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D107)Instrument Panel>Instrument Panel Wire>FC Water Release Switch

A8-11 (WDRN) - D107-5 (SW) Always Below 1 Ω
A8-11 (WDRN) or D107-5 (SW) - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition

Click Location & Routing(D15,D107)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

Click Connector(D107)Instrument Panel>Instrument Panel Wire>FC Water Release Switch

D15-11 (WDRN) - D107-5 (SW) Always Below 1 Ω
D15-11 (WDRN) or D107-5 (SW) - Body ground Always 10 kΩ or higher



d.

Reconnect the FC water release switch connector.


e.

Reconnect the EV control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR